Apc BK500EI Handleiding

Apc Server BK500EI

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BK500EI (2 pagina's) in de categorie Server. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

USB

RJ-45

In situations where the Back-UPS or connected equipment appears too sensitive to input voltage, it may be

necessary to adjust the transfer voltage. This is a simple task requiring use of the front panel pushbutton. To

adjust the transfer voltage, proceed as follows:

1. Plug the Back-UPS into the utility power source. The Back-UPS will be in a Standby Mode (no indicators lit).

2. Press the front panel pushbutton fully inward for 10 seconds. All indicators on the Back-UPS will flash to

acknowledge going into Programming Mode.

3. The Back-UPS will then indicate its current Sensitivity Setting, as shown in the following table.

4. To select the Low Sensitivity setting, press the pushbutton until the yellow indicator is flashing.

5. To select the Medium Sensitivity setting, press the pushbutton until the yellow and red indicators (second and

third from the top) are flashing.

6. To select the High Sensitivity setting, press the pushbutton until yellow and both red indicators (bottom three)

are flashing.

7. To exit without changing the Sensitivity Setting, press the pushbutton until the green indicator is flashing.

8. Once in Programming Mode, if the pushbutton is not pressed within 5 seconds, the Back-UPS will exit

Programming Mode; all indicators will extinguish.

Indicators

Flashing

Sensitivity

Setting

Input Voltage

Range

(for utility

operation)

Use When

(yellow)

Low 160 - 278 Vac Input voltage is extremely low or

high. Not recommended for computer

loads.

(yellow, and red)

Medium

(factory default)

180 - 266 Vac Back-UPS frequently goes On

Battery.

(yellow, red, and red)

High 196 - 256 Vac Connected equipment is sensitive to

voltage fluctuations (recommended).

Back-UPS™

350/500/650

User’s Manual

990-9237 3/04

Installation

2Connect Equipment

The rear panel of the Back-UPS consists of the

following elements:

Battery Back Up Outlets (qty. of 3). These

outlets provide battery back-up, surge protection,

and Electro-magnetic Interference (EMI) filtering.

In case of power outage, battery power is

automatically provided to these outlets. Power

(utility or battery) is not supplied to these outlets

when the Back-UPS is switched Off. Connect a

computer, monitor, and external disk or CD-ROM

drive to these outlets.

Surge Only Outlet. This outlet is always On

(when utility power is available) and is not

controlled by the On/Off switch. This outlet does

not provide power during a power outage. Connect

a printer, fax machine or scanner to this outlet.

Note: Allow the Back-UPS to charge for a full eight

hours prior to use.

Press the push-button on the front panel of the Back-

UPS.

Observe that the following events occur after

pressing and releasing the push-button:

• The green On-Line indicator flashes.

• The yellow On Battery indicator lights while

the Self-Test is being performed.

• When Self-Test has successfully completed,

only the green On Line indicator will be lit.

• If the internal battery is not connected, (see Step

1 above) the green On Line indicator and red

Replace Battery indicator will light. The Back-

UPS will also emit a chirping sound.

ON LINE

ON BATTERY

OVERLOAD

REPLACE BATTERY

5Connect USB Cable

There are four status indicators (lights) on the front

panel of the Back-UPS (On Line, On Battery,

Overload, and Replace Battery).

On Line (green) - is lit whenever utility

power is powering the Battery Backup

outlets.

ON LINE

ON BATTERY

OVERLOAD

REPLACE BATTERY

On Battery (yellow) - is lit whenever

the battery of the Back-UPS is powering

equipment connected to the Battery

Backup Outlets.

Four Beeps Every 30 Seconds - this

alarm is sounded whenever the Back-

UPS is running On Battery. Consider

saving work in progress.

Continuous Beeping - this alarm is

sounded whenever a low battery

condition is reached. Battery run-time

is very low. Promptly save any work

in progress and exit all open

applications. Shutdown the operating

system, computer and the Back-UPS.

Overload (red) - is lit whenever

power demand has exceeded the capac-

ity of the Back-UPS.

Continuous Tone - this alarm is

sounded whenever the Battery Backup

outlets are overloaded.

Circuit Breaker - the circuit

breaker button located on the rear

panel of the Back-UPS will stick

out if an overload condition forces

the Back-UPS to disconnect itself

from utility power. If the button

sticks out, disconnect non-

essential equipment. Reset the

circuit breaker by pushing the

button inward.

1Placement / Power 3Connect the Phone

Line to Surge Protection

Avoid placing the Back-UPS in:

• Direct sunlight

• Excessive heat

• Excessive humidity or in contact with fluids

of any type

Plug the Back-UPS into a wall outlet, as shown.

• The Back-UPS charges the internal battery

any time it is connected to a wall outlet.

Your computer’s power cord.

The telephone ports provide lightning surge

protection for any device connected to the telephone

line (computer, modem, fax or telephone). The

telephone ports are compatible with Home Phoneline

Networking Alliance (HPNA) and Digital Subscriber

Line (DSL) standards, as well as all modem data

rates. Connect as shown.

Wall Outlet

Modem/Phone/Fax

Replace Battery (red) - is lit when-

ever the battery is near the end of its use-

ful life, or if the battery is not connected

(see above). A battery that is near the

end of its useful life has insufficient run-

time and should be replaced.

Chirps for 1 Minute Every 5 Hours -

this alarm is sounded whenever the

battery has failed the automatic

diagnostic test.

to the Back-UPS

4Switch on the

Back-UPS

Replace the Internal Battery

To replace the internal battery, proceed as follows:

Note: Replacing the battery is a safe procedure. However, small sparks may occur

during the process. This is normal.

Place the unit on its side. Slide the battery

compartment cover upward and off of the UPS.

3 4

Align the battery compartment cover with the

grooves in the UPS. Slide the cover down

until it locks.

Pull the battery out, exposing the battery

terminals and wires. Disconnect the wires from

the terminals.

Slide the new battery into the battery

compartment. Connect the battery wires to the

terminals as follows:

Black wire to Ground (-) terminal

Red wire to Positive (+) terminal

and Install Software

(optional)

NOTE: Macintosh Users - for full USB

performance, use Mac OS 10.1.5 or higher.

If Autoplay is not enabled on the computer,

proceed as follows:

1. On the computer desktop of the display,

double-click on My Computer.

2. Double-click on the CD-ROM drive icon and

follow the on-screen instructions.

Follow the

on-screen

instructions.

Status Indicators and Alarms

Order Replacement Battery

The typical battery lifetime is 3-6 years (depending on the number of discharge cycles and operating

temperature). A replacement battery can be ordered over the phone from APC, or the battery can be ordered

on-line from the APC web site (http://www.apc.com, a valid credit card is required).

When ordering, please specify Battery Cartridge RBC2 (Back-UPS 350/500) or RBC17 (Back-UPS 650).

Transfer Voltage and Sensitivity Adjustment (optional)

APC, Back-UPS, and PowerChute are registered trademarks of American Power Conversion.

All other trademarks are property of their respective owners.

Back-UPS does not power computer/monitor/external drive during an outage

Internal battery is not connected.

Computer, monitor or external disk/

CD-ROM drive is plugged into a

Surge Only outlet.

Check the battery connections

Move computer, monitor, or external drive power cord plug to the

Battery Backup outlets.

Back-UPS operates on battery although normal utility voltage exists

Back-UPS circuit breaker “tripped”.

The wall outlet that the Back-UPS is

connected to does not supply utility

power to the unit.

Disconnect non-essential equipment from the

Back-UPS. Reset the circuit breaker (located

on the rear panel of the Back-UPS) by push-

ing the circuit breaker button fully inward

until it catches.

Back-UPS does not provide expected backup time

Back-UPS is excessively loaded.

Back-UPS battery is weak due to

recent outage and has not had time

to recharge.

Battery requires replacement.

Unplug non-essential Battery Backup connected equipment, such as

printers and plug them into Surge Only outlets.

Note: Devices that have motors or dimmer switches (laser printers,

heaters, fans, lamps, and vacuum cleaners, for example) should not be

connected to the Battery Backup outlets.

Charge the battery. The battery charges whenever the Back-UPS is

connected to a wall outlet. Typically, eight hours of charging time are

needed to fully charge the battery from total discharge. Back-UPS

run-time is reduced until the battery is fully charged.

Replace battery (see Order Replacement Battery). Batteries typically

last 3-6 years, shorter if subjected to frequent power outages or ele-

vated temperatures.

A red indicator is lit

Battery is not connected properly.

The Overload indicator is lit if

equipment connected to the Battery

Backup outlets is drawing more

power than the Back-UPS can pro-

vide.

Battery requires replacement.

Check the battery connections.

Move one or more equipment power plugs to the Surge Only outlets.

The battery should be replaced within two weeks (see "Order

Replacement Battery"). Failure to replace the battery will result in

reduced run-time during a power outage.

Connect the Back-UPS to another wall outlet or have a qualified

electrician check the building wiring.

Red indicators are flashing

Back-UPS failure. Call APC for service.

Service

1. Consult the Troubleshooting section to eliminate common problems.

2. Determine if the circuit breaker is tripped. If the circuit breaker is tripped, reset the breaker and

determine if the problem still exists.

3. If the problem persists, consult the APC Worldwide Web site (www.apcc.com) or call customer

service.

• Record the model number of the UPS, the serial number, and the date purchased. Be prepared to

troubleshoot the problem over the telephone with a technician. If this is not successful, the

technician will issue a Return Merchandise Authorization Number (RMA#) and a shipping

address.

• If the UPS is under warranty, repairs are free. If not, there is a repair charge.

4. Pack the UPS in its original packaging. If the original packing is not available, ask customer service

about obtaining a new set. Pack the UPS properly to avoid damage in transit.

5. Write the RMA# on the outside of the package.

6. Return the UPS by insured, prepaid carrier to the address provided by customer service.

Note: If the UPS requires service, do not return it to the dealer. The following steps should

be taken:

Note: Never use StyrofoamTM beads for packaging. Damage sustained in transit is

not covered under warranty (insuring the package for full value is recommended).

Warranty

The standard warranty is two (2) years from the date of purchase. APC’s standard procedure is to replace

the original unit with a factory reconditioned unit. Customers who must have the original unit back due

to assigned asset tags and set depreciation schedules must declare such a need at first contact with an

APC Technical Support representative. APC will ship the replacement unit once the defective unit has

been received by the repair department, or cross ship upon the receipt of a valid credit card number. The

customer pays for shipping the unit to APC. APC pays ground freight transportation costs to ship the

replacement to the customer.

APC Contact Information

Replace Battery indicator lit and an alarm sounds when the Back-UPS is turned on

Internal battery not connected. Check the battery connections.

USA/Canada

Mexico

Brazil

Worldwide

Internet

Technical Support

1.800.800.4272

292.0253 / 292.0255

0800.12.72.1

1.401.789.5735

http:\\www.apc.com

http:\\www.apc.com/support

Troubleshooting

Use the tables below to solve minor Back-UPS installation and operation problems. Consult APC On-line

Technical Support or call APC Technical Support for assistance with problems that cannot be resolved using

this document:

Possible Cause Procedure

Back-UPS will not switch on

Back-UPS not connected to an AC

power source.

Back-UPS circuit breaker “tripped”.

Very low or no utility voltage.

Portable generator being used to

provide input voltage.

Check that the Back-UPS power plug is

securely connected to the wall outlet.

Disconnect non-essential equipment from the

Back-UPS. Reset the circuit breaker (located

on the rear panel of the Back-UPS) by push-

ing the circuit breaker button fully inward

until it catches. If the circuit breaker resets,

switch the Back-UPS on and reconnect the

equipment one-at-a-time. If the circuit

breaker trips again, it is likely that one of the

connected devices is causing the overload.

Check the wall outlet that supplies power to

the Back-UPS using a table lamp. If the lamp

bulb is very dim, have the utility voltage

checked by a qualified electrician.

Set the Transfer Voltage and Sensitivity

setting to Low (see Transfer Voltage and

Sensitivity Adjustment). By setting the Back-

UPS to Low sensitivity, it can accept a wider

range of input voltage.

Specifications

Input Voltage (on line)

Frequency Limits (on line)

On Battery Waveshape

Maximum Load

Typical Recharge Time

Operating Temperature

Storage Temperature

Operating and Storage

Relative Humidity

Size (H x W x D)

Weight

Shipping Weight

EMI Classification

On Battery Run-Time

Back-UPS Storage

Before storing, charge the Back-UPS for at least eight hours. Store the Back-UPS covered and upright in

a cool, dry location. During storage, recharge the battery in accordance with the following table:

Please contact APC Technical Support to troubleshoot the unit before returning it to APC.

Storage Temperature Recharge Frequency Charging Duration

-5o to 30oC (23o to 86oF)

30 o

to 45oC (86o to 113 oF)

Every 6 months

Every 3 months

8 hours

123

456

789

180 - 266 Vac (default setting)

47 - 63 Hz (auto-sensing)

Stepped Sine Wave

350 VA - 210 W 500 VA - 300 W 650 VA - 400 W

8 Hours

0o to 40oC (32o to 104oF)

-15 o

to 45oC (5o to 113oF)

5 to 95% non-condensing

16.5 x 9.2 x 28.5 cm (6.5 x 3.6 x 11.2 inches)

350 VA - 5.7 kg (12.5 lb) 500 VA - 5.9 kg (12.9 lb)

650 VA - 6.2 kg (13.6 lb.)

350 VA - 6.8 kg (14.9 lb) 500 VA - 7.0 kg (15.3 lb)

650 VA - 7.3 kg (16.1 lb.)

EN 55022, IEC 801-2 and 801-4 (level IV), and IEC 801-3 (level III)

350 VA - 13.2 minutes (typical) - computer and

17" (43.2 cm) monitor.

500 VA - 10.8 minutes (typical) - computer and

21" (53.3 cm) monitor.

650 VA - 17 minutes (typical) - computer and

21" (53.3 cm) monitor.

Product specificaties

Merk:	Apc
Categorie:	Server
Model:	BK500EI
Kleur van het product:	Beige
Gewicht:	6320 g
Breedte:	91 mm
Diepte:	284 mm
Hoogte:	165 mm
Snoerlengte:	1.83 m
Geluidsniveau:	40 dB
Gewicht verpakking:	7050 g
Breedte verpakking:	241 mm
Diepte verpakking:	368 mm
Hoogte verpakking:	178 mm
LED-indicatoren:	Batterijvervanging
Vormfactor:	Tower
USB-poort:	Ja
Meegeleverde kabels:	Phone (RJ-11), USB cable
Garantiekaart:	Ja
Accu/Batterij voltage:	12 V
Certificering:	C-tick, CE, EN 50091-1, EN 50091-2, GOST, VDE, REACH
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS, ENERGY STAR
Meegeleverde software:	PowerChute Personal Edition
Uitgangsvermogen:	300 W
Batterij capaciteit:	7 Ah
Accu/Batterij oplaadtijd:	8 uur
Temperatuur bij opslag:	-15 - 45 °C
Stroomspanning bescherming:	Overbelasting
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Filtratie:	Ja
Snelle installatiehandleiding:	Ja
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Stekker:	C14 stekker
Efficientie:	99 procent
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Producten per pallet:	48 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Code geharmoniseerd systeem (HS):	85078000
Surge energy rating:	310 J
Aantal AC uitgangen:	4 AC-uitgang(en)
Nominale input voltage:	230 V
Stopcontacttypes:	C13 stekker
Golf protectie functies:	Digital Subscriber Line (DSL), Fax, Modem, Telephone
Software-cd:	Ja
Output power capacity:	0.5 kVA
Ingang operation voltage (min):	160 V
Ingang operation voltage (max):	300 V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	- V
UPS-topologie:	Stand-by (Offline)
Typische backup tijd op halve lading:	13.8 min
Typische backup tijd op volledige lading:	3.8 min
Netspanning, in bedrijf:	230 V
Hoorbare alarmstanden:	Low battery alarm, Overload alarm
Spanningsbeveiliging:	Ja
Golfvorm:	Sinus
Uitgangsfrequentieregeling:	47 - 63 Hz
Number of output IEC jumpers:	2
Contacttijd (max):	10 ms
Contacttijd (min):	6 ms
Automatische batterij test:	Ja
Acculevensduur (max):	6 jaar