Apc BE750G Handleiding

Apc UPS BE750G

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BE750G (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Back-UPS ES 750

User’s Guide

Connect Battery

Power On and Install

Software

Surge Protection

These outlets provide full-time protection from surges even if the Back-UPS ES

is switched OFF. Plug your printer, fax machine, scanner, or other peripherals

that do not need battery power into these outlets.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet;

not a surge protector or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of

the operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other end

of the cable to the USB port on your computer. The software will automatically

find the USB Port of your computer.

Battery Back-up + Surge Protection

These outlets are powered whenever the Back-UPS ES is switched ON. During

a power outage or other utility problems (brownouts, over-voltages), these

outlets will be powered for a limited time by the Back-UPS ES. Plug your

computer, monitor, CD-ROM drive and one other data-sensitive device such as

an external disk or tape drive, or Home Phoneline Networking Association

(HPNA) device into these outlets.

Press the ON/OFF switch to power the unit ON.

A single short beep and the green “Power On” indicator

confirms the Back-UPS ES is on and ready to provide

protection.

The Back-UPS ES should charge for at least 16 hours to ensure

sufficient runtime. The unit is being charged whenever it is

connected to utility power, whether the unit is turned ON or

OFF.

If the red Building Wiring Fault indicator (located on the end

near the power cord) is lit, your building wiring presents a shock

hazard that should be corrected by a qualified electrician.

Install the PowerChute® Personal Edition

software

Place the PowerChute Personal Edition CD-ROM into your

computer and follow the installation instructions on the screen.

.apc.com

The Back-UPS ES indicates operating status using a combination

of visual and audible indicators. Use the following table to identify

the status of the Back-UPS ES.

Status

Visual Indications

(Power On - Green)

(Replace Battery - Red) Audible Indication

Alarm Terminates

When

Power On - UPS is supplying conditioned utility

power to the load. Power On LED - ON None Not applicable.

On Battery - UPS is supplying battery power to

load connected to Battery outlets. Power On LED - ON (off

during beep) Beeping 4 times

every 30 seconds UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is supplying battery

power to the load connected to the Battery outlets

and the battery is near exhaustion.

Power On LED - flashing

(every 1/2 second) Rapid beeping

(every 1/2 second) UPS transfers back to

normal operation, or

when UPS is turned off.

Replace Battery - The battery is disconnected.

The battery is in need of charging or is at the end

of its usual life and must be replaced.

Power On and Replace

Battery LEDs- Flashing

(alternating)

Replace Battery LED -

flashing

Constant tone

UPS is turned off with

the power switch.

Overload Shutdown - During On Battery

operation a battery power supplied outlet

overload was detected.

None Constant tone UPS turned off with the

power switch.

Overload Alarm - Online power exceeded

Back-UPS capacity. Power On LED - ON Constant tone Equipment power plugs

are moved from Battery

Backup outlets to

Surge or Client outlets.

Sleep Mode - During On Battery operation the

battery power has been completely exhausted,

and the UPS is waiting for utility power to return

to normal.

None Beeping once every

4 seconds Utility power is

restored, or if utility

power is not restored

within 32 seconds, or

the UPS is turned off.

Building Wiring Fault - Your building wiring

presents a shock hazard that should be corrected

by a licensed electrician.

Building Wiring Fault LED

(red) - ON None UPS is unplugged, or is

plugged into a properly

wired outlet.

Status Indicators

See the Troubleshooting section for additional assistance.

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe battery terminal.

NOTE: Small sparks may occur during battery connection. This is normal.

Turn the Back-UPS ES over and press in the release tab.

Slide the plastic battery cover off the unit. Insert the battery back into the compartment. Slide the

plastic battery cover back in place until the tab locks.

Connect Equipment

BatteryCover

Release Tab

Battery

Terminals

Connect the battery wire firmly to the battery terminal.

Idle peripheral devices (printer/scanners, speakers) continue to draw power when not in use. To conserve

power, the Back-UPS uses “master controlled outlets”. The Master outlet senses when the master device

(computer) that is plugged into the Master outlet is no longer drawing current, and automatically shuts off

power to the Controlled outlets. Pressing the MASTER ENABLE button for one second enables and disables

this feature. When enabled, the green MASTER ENABLE LED is lit (on). When it is disabled, the LED is not

lit (off). The Back-UPS ships with MASTER ENABLE activated. Note: Do not connect peripherals to the

Controlled Outlets if you want them to continue to run when your computer is turned off.

Threshold Programming

When the computer is turned off, the Master outlet shuts off power to the Controlled outlets. However, when

the computer goes into “hibernation (sleep) mode” the Master outlet may not properly recognize the reduced

power level. To ensure the Master outlet shuts off power to the Controlled outlets properly, the threshold set-

ting may need to be adjusted from the “default value”. If the peripherals plugged into the Controlled outlets

do not turn off when the computer goes into hibernation mode, first ensure the MASTER ENABLE LED is lit,

and if so, then perform the procedure provided below to switch the threshold setting to High. Conversely, if

the computer has an extremely low power level, it may require that the threshold setting be set to Low if the

Controlled outlets automatically shut off, even when the computer is running. The Back-UPS automatically

exits this mode in five seconds if no buttons are pushed, or no operations are run. The three threshold set-

tings that can be selected are summarized in the table below.

Perform the following steps to change the threshold settings:

1. Plug the Back-UPS into the utility power source; do not turn power on. The unit will be in standby mode

(no LEDs are lit).

2. Press and hold down the MASTER ENABLE button for 10 seconds, until all indicators flash to show it has

entered threshold programming mode.

3. When the MASTER ENABLE button is released, the LEDs that are illuminated indicate the current thresh-

old setting (Low, Medium or High).

4. Press the MASTER ENABLE button to select a different threshold setting.

Indicators Flashing Threshold Setting

Input Wattage Range

(Hibernation Mode)

1. Master Enable LED Low 10 Watts

2. Master Enable LED, On Line LED Medium (default) 25 Watts

3. Master Enable, On Line, Replace Battery LEDs High 60 Watts

Master/Controlled Outlets

Battery Wires

Connect Modem / Phone / DSL / Fax / 10/100Base-T / HPNA /

Cable Modem / CATV or DSS to Surge Protection

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber

Line - DSL), Home Phoneline Networking Association (HPNA) type equipment,

modem, 10/100Base-T Ethernet, or fax machines from surges when connected

through the UPS as shown in the drawing. The UPS also protects a cable

modem, CATV converter, or DSS receiver from surges when it is connected

through the UPS coaxial connectors as shown in the drawing.

Master

Controlled by Master

Battery Backup+

Surge Protection

From Wall Jack

Dataline Output to

DSL Modem, Phone

Building Wiring

Fault Indicator

Cable Input

from Internet

Service

Cable Output

to Cable,

Modem, CATV

Converter,

or DSS Input

Circuit

Breaker

Troubleshooting

Use the table below to solve minor Back-UPS ES installation or operation problems. Consult APC Online Technical Support or call APC

Technical Support for assistance with problems that cannot be resolved using the table below:

Back-UPS ES will not turn on.

No power available at the Surge Protection

outlets.

Back-UPS turns on, but LED flashes and unit

emits a constant tone.

Connected equipment loses power.

The Power On indicator is lit and the Back-

UPS ES is beeping four times every 30

seconds.

The Power On indicator flashes and beeps

twice per second at the same time.

Building Wiring Fault indicator is lit.

Inadequate runtime.

No phone/fax/DSL/cable or network signal

from the Back-UPS.

Connect the battery (see Connect Battery) and ensure power is available at the wall

outlet. If battery is connected and power is unavailable, the unit can be “cold started”

(operated on battery power) by holding the power button down until two beeps are

heard.

Reduce the amount of equipment plugged into Surge Protection outlets.

Ensure the fuse or circuit breaker for the outlet is not tripped, and that the wall switch

controlling the outlet (if any) is in the ON position.

Connect the battery (see Connect Battery diagram).

Ensure the equipment you want to stay powered during a power failure is plugged

into the “Battery Backup plus Surge Protection” outlets and NOT the “Surge

Protection” outlets.

Make sure the equipment plugged into the outlets of the unit are not overloading its

capacity. Try removing some of the equipment and see if the problem continues.

The Back-UPS ES is operating normally.

The Back-UPS ES can only operate on battery power for a limited amount of time.

The unit will eventually turn oﬀ when the available battery power has been used.

Allow the unit to recharge for 16 hours before expecting maximum runtime.

The output waveform is designed for computers and computer-related equipment. It

is not designed for use with motor-type equipment.

Contact APC Technical Support for further troubleshooting.

The Back-UPS ES is operating normally and using battery power. Once On Battery,

you should save your current work, power down your equipment, and turn the unit

OFF. Once normal power is restored, you may turn the unit back ON and power your

equipment.

The Back-UPS ES is about to shut off due to a low battery charge condition! When

the unit beeps twice every second, the battery has about 2 minutes of power

remaining. Immediately power down your computer and turn the unit OFF. When

normal power returns, the unit will recharge the battery.

Call a qualified electrician for service.

Allow the unit to charge by leaving it plugged into the wall for at least 16 hours.

As a battery ages, the amount of runtime available will decrease. You can replace the

battery by ordering one at www.apc.com. Batteries also age prematurely if the Back-

UPS ES is placed near excessive heat.

Make sure the data line from the wall outlet is connected to the jack labeled “Wall

Outlet (Phone/Fax/DSL), or “Cable In” (Cable/DSS/CATV).

Problem Probable Cause Solution

Specifications

Warranty

Service

APC Contact Information

Input Voltage 120 Vrms Nominal

Frequency 50 - 60 Hz (auto-sensing)

Brownout Transfer 88 Vrms, typical

Over-voltage Transfer 142 Vrms, typical

Output UPS Capacity (5 outlets) 750 VA / 450 W

Total Amperage (10 outlets) 12 Amps (including UPS output)

Voltage

On Battery 115 Vrms + 8%

(step-approximated sine wave)

Frequency - On Battery 50-60 Hz + 1 Hz

Transfer Time 6 ms typical, 10 ms maximum

Protection and Filter AC Surge Protection Full time, 354 joules

Phone/Fax/DSL Surge

Protection Single line (2-wire)

Cable/CATV/DSS Surge

Protection One Coax Input/Output

Network Surge Protection 10/100Base-T Ethernet

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery Model RBC17

Type Sealed, maintenance-free lead acid

Average Life 3 - 5 years depending on the number of discharge

cycles and environmental temperature

Physical Net Weight 10.36 lb. (4.70 kg.)

Size 3.5" (H) x 13.5" (W) x 7.1" (D)

(88.3 x 342.7 x 180.0 mm)

Operating Temperature +32oF to 104oF (0oC to 40oC)

Storage Temperature +5oF to 113oF (-15oC to 45oC)

Operating Relative Humidity 0 to 95% non-condensing

Operating Elevation 0 to 10,000 ft (0 to 3,000m)

Safety/Regulatory Safety Approvals TUV C-US certified per UL Std. 1778 and CSA 22.2

No. 107.1, NOM-001

EMC Compliance Notice: This device complies with part 68 and

part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This device may

not cause harmful interference, and (2) This

device must accept any interference received,

including interference that may cause undesired

operation.

On the bottom of this equipment is a label that

contains, among other information, the FCC

registration number and ringer equivalence

number (REN) for this equipment.

If requested, this information must be provided

to the telephone company.

Model BE750G

The standard warranty is 3 years from the date of purchase. APC’s standard procedure

is to replace the original unit with a factory reconditioned unit. Customers who must

have the original unit back due to assigned asset tags and set depreciation schedules

must declare such a need at first contact with APC Technical Support. APC will ship the

replacement unit once the defective unit is received by the repair department or cross-

ship upon the provision of a valid credit card number. The customer pays for shipping

to APC, and APC pays ground freight transportation costs back to the customer.

Please DO NOT RETURN Back-UPS ES to the place of purchase under any

circumstances.

1. Consult the Troubleshooting section to eliminate common problems.

2. Verify the battery is connected (see Connect Battery) and that the Circuit Breaker is

not tripped (see Troubleshooting section).

If you still have problems or questions, please contact APC via the internet or at one of

the phone numbers listed below.

3. Before contacting APC, please be sure to record the date purchased, UPS model,

and serial number (on bottom of unit).

4. Be prepared to troubleshoot the problem over the telephone with a Technical

Support Representative. If this is not successful, the representative will issue a Return

Material Authorization Number (RMA#) and a shipping address.

5. Pack the unit in its original packaging. If the original packaging is not available, ask

APC Technical Support about obtaining a new set. Pack the unit properly to avoid

damage in transit. Never use foam beads for packaging. Damage sustained in transit is

not covered under warranty (insuring the package for full value is recommended).

6. Write the RMA# on the outside of the package.

7. Return the unit by insured carrier to you by APC Technical the address given to

Support.

Online Technical Support: http://support.apc.com

http://www.apc.com/support

esupport@apcc.com

Web Site: www.apc.com

USA/Canada: 1.800.800.4272

Mexico: +52.292.0253 / 52.292.0255

Brazil: +0800.12.72.1

Worldwide: +1.401.789.5735

Order Replacement Battery

Replace with an APC qualified battery. Replacement batteries can be ordered from

www.apc.com (valid credit card required). Have your Back-UPS ES model number

available when ordering. Your model number can be found on the bottom of the unit.

The battery is disconnected, and either power is

unavailable at the wall outlet, or utility power is having a

“brownout” or an “over voltage” condition.

Surge Protection outlets have been overloaded.

Utility power not available at the wall outlet.

Battery is disconnected.

Equipment is connected to the “Surge Protection” outlets.

The Back-UPS ES is overloaded.

PowerChute Personal Edition software has performed a

shutdown due to a power failure.

The Back-UPS ES has exhausted its available battery

power.

Connected equipment does not accept the step-

approximated sine waveform the Back-UPS ES.

The Back-UPS ES may require service.

The Back-UPS ES is using battery.

Battery capacity is low (about 2 minutes of use remaining).

Your building wiring presents a shock hazard. Using the

Back-UPS with this condition will void the warranty.

The battery is not fully charged.

Battery is near the end of useful life.

Data line from the ISP or wall outlet is connected to the

wrong jack on the Back-UPS.

Internet connection lost during power outage. Modem lost AC power. Plug the modem’s AC power cord into one of the “Battery Back-up plus Surge

Protection” outlets.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

All other trademarks are property of their respective owners.

990-3153A 9/07

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	BE750G
Kleur van het product:	Zwart
Gewicht:	4700 g
Snoerlengte:	1.8 m
Gewicht verpakking:	5700 g
LED-indicatoren:	Ja
Afmetingen verpakking (BxDxH):	258 x 452 x 151 mm
Certificering:	FCC Part 15 Class B/FCC Part 68/NOM/UL 1778
Uitgangsvermogen:	450 W
Accu/Batterij oplaadtijd:	16 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	5 - 95 procent
Gewicht (imperiaal):	10.34 lbs
Bedrijfstemperatuur, bereik:	0 - 40 °F
Hoogte, in bedrijf:	0 - 3000 m
Relatieve luchtvochtigheid bij opslag (geen condensering):	0 - 95 procent
Afmetingen (B x D x H):	180 x 343 x 88 mm
Producten per pallet:	72 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Surge energy rating:	365 J
Nominale input voltage:	120 V
Input-connectietype:	NEMA 5-15P
Output power capacity:	0.75 kVA
Typische backup tijd op halve lading:	11.3 min
Typische backup tijd op volledige lading:	2.3 min
Hot-swap batterij:	Ja
Netspanning, in bedrijf:	120 V
Output-aansluitingen:	10 x NEMA 5-15R