Apc BE650G Handleiding

Apc UPS BE650G

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BE650G (2 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Back-UPS ES 650

User’s Guide

Connect Battery

Equipment

Power On and

Install Software

All other trademarks are property of their respective owners.

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS ES is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into

these outlets.

Battery Back-up +Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS ES. Plug your computer,

monitor, CD-ROM drive and two other data-sensitive devices

such as an external disk or tape drive, or Home Phoneline

Networking Association (HPNA) device into these outlets.

Press the ON/OFF switch to power the unit

ON.

A single short beep and the green “Power On”

indicator confirms the Back-UPS ES is on and

ready to provide protection.

The Back-UPS ES should charge for at least 16

hours to ensure sufficient runtime. The unit is

being charged whenever it is connected to utility

power, whether the unit is turned ON or OFF.

If the red Building Wiring Fault indicator (located

on the end near the power cord) is lit, your

building wiring presents a shock hazard that

should be corrected by a qualified electrician.

Install the PowerChute® Personal Edition

software

Place the PowerChute Personal Edition CD-

ROM into your computer and follow the

installation instructions on the screen.

.apc.com

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

The Back-UPS ES indicates operating status using a combination of visual and audible indicators.

Use the following table to identify the status of the Back-UPS ES.

Status Visual Indications

(Power On - Green)

(Replace Battery - Red)

Audible Indication Alarm Terminates

When

Power On - UPS is supplying conditioned

utility power to the load. Power On pushbutton -

ON (lit) None Not applicable.

On Battery - UPS is supplying battery

power to the load connected to the Battery

outlets.

Power On pushbutton -

ON (off during beep) Beeping 4 times every

30 seconds UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is supplying

battery power to the load connected to the

battery outlets, and the battery is near

exhaustion.

Replace Battery indicator

is flashing Rapid beeping (every

1/2 second) UPS transfers back to

normal operation, or

when UPS is turned off.

Replace Battery - The battery is

disconnected.

The battery is in need of charging, or is at

the end of its usual life and must be

replaced.

Replace Battery indicator

is Flashing

Power On and Replace

Battery indicators -

flashing (alternating)

Constant tone

UPS is turned off with

the power switch.

Overload Shutdown - During On Battery

operation a battery power supplied outlet

overload was detected.

None Constant tone UPS is turned off with

the power switch.

Sleep Mode - During On Battery operation

the battery power has been completely

exhausted and the UPS is waiting for utility

power to return to normal.

None Beeping once every 4

seconds Utility power is restored,

or if utility power is not

restored within 32

seconds, or the UPS is

turned off.

Building Wiring Fault - Your building

wiring presents a shock hazard that should

be corrected by a licensed electrician.

Building Wiring Fault LED

(red) - ON None UPS is unplugged, or

UPS is plugged into a

properly wired outlet.

Status Indicators

See the Troubleshooting section for additional assistance.

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe

battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.

Turn the Back-UPS ES over and press in the

release tab. Slide the plastic battery cover

off of the Back-UPS.

Insert the battery back into the compartment.

Slide the plastic battery cover until the release

tab locks into place.

Connect the red battery wire firmly to

the positive (+) battery terminal.

1 2 3

Connect

Connect Modem / Phone / DSL / Fax / 10/100Base-T / HPNA / Cable Modem / CATV

or DSS to Surge Protection

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line -

DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, 10/100

Base-T Ethernet, or fax machines from surges when connected through the UPS as

shown in the drawing below.

The UPS also protects a cable modem, CATV converter, or DSS receiver from surges

when it is connected through the UPS coaxial connectors as shown in the drawing below.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not into a surge

protector or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of the

operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other end of the

cable to the USB port on your computer. The software will automatically find the

computer’s USB Port.

BATTERY DOOR

RELEASE TAB

Power On/Off

Switch & Indicator

Replace

Battery

Indicator

NOTE:

Replace Battery Indicator is only visible when illuminated.

Circuit Breaker

Push to Reset

From Wall

Outlet Dataline outpu to

em, Fa x, or

t DSL,

Mod Network

(10/100BASE-T)

Data Port

Cable output to Cable Modem,

CATV converter or DSS input

Cable i nput from Internet Service

Provider (ISP), CATV or DSS

Troubleshooting

Use the table below to solve minor Back-UPS ES installation or operation problems. Consult APC Online Technical Support or call APC

Technical Support for assistance with problems that cannot be resolved using the table below:

Back-UPS ES will not turn on.

No power available at the Surge Protection

outlets.

Back-UPS is on, but Replace Battery indicator

flashes, and unit emits a constant tone.

Connected equipment loses power.

The Power On indicator is lit and the Back-

UPS ES beeps four times every 30 seconds.

The Power On indicator flashes and the Back-

UPS beeps twice per second at the same time.

Building Wiring Fault indicator is lit.

Inadequate runtime.

No phone/fax/DSL/cable or network signal

from the Back-UPS.

Internet connection lost during power outage.

Connect the battery (see Connect Battery) and ensure power is available at the wall

outlet. If battery is connected and power is unavailable, the unit can be “cold

started” (operated on battery power) by holding the power button down until two

beeps are heard.

Reduce the amount of equipment plugged into the Surge Protection outlets.

Ensure the fuse or circuit breaker for the outlet is not tripped, and that the wall switch

controlling the outlet (if any) is in the ON position.

Connect the battery (see Connect Battery diagram).

Ensure the equipment you want to stay powered during a power failure is plugged

into the “Battery Backup plus Surge Protection” outlets and NOT the “Surge

Protection Only” outlets.

Make sure the equipment plugged into the outlets of the unit are not overloading its

capacity. Try removing some of the equipment and see if the problem continues.

The Back-UPS ES is operating normally.

The Back-UPS ES can only operate on battery power for a limited amount of time.

The unit will eventually turn off when the available battery power has been used.

Allow the unit to recharge for 16 hours before expecting maximum runtime.

The output waveform is designed for computers and computer-related equipment. It

is not designed for use with motor-type equipment.

Contact APC Technical Support for further troubleshooting.

The Back-UPS ES is operating normally, and using battery power. Once On Battery,

you may want to save your current work, power down your equipment, and turn the

unit OFF. Once normal power is restored, you may turn the unit back ON, and power

your equipment.

The Back-UPS ES is about to shut off due to a low battery charge condition! When

the unit beeps twice every second, the battery has about 2 minutes of power

remaining. Immediately power down your computer ,and turn the unit OFF. When

normal power returns, the unit will recharge the battery.

Call a qualified electrician for service.

Allow the unit to charge by leaving it plugged into the wall at least 16 hours.

As a battery ages, the amount of runtime available will decrease. You can replace

the battery by ordering one at www.apc.com. Batteries also age prematurely if the

Back-UPS ES is placed near excessive heat.

Make sure the data line from the wall outlet is connected to the jack labeled “Wall

Outlet”, or “Cable In” (Cable/DSS/CATV).

Plug the AC power cord of the modem into one of the four “Battery Back-up plus

Surge Protection” outlets.

Problem Probable Cause Solution

Specifications

Warranty

Service

APC Contact Information

Input Voltage 120 Vrms nominal

Frequency 50 - 60 Hz (auto-sensing)

Brownout Transfer 88 Vrms, typical

Over-voltage Transfer 139 Vrms, typical

Output UPS Capacity (4 outlets) 650 VA / 390 W

Total Amperage (8 outlets) 12 Amps (including UPS output)

Voltage - On Battery 115 Vrms + 8% (step-approximated sine wave)

Frequency - On Battery 50 - 60 Hz + 1 Hz

Transfer Time 6 ms typical, 10 ms maximum

Protection and

Filter AC Surge Protection Full time, 375 joules

Phone/fax/DSL Surge

Protection Single line (2-wire)

Cable/CATV/DSS Surge

Protection One Coax Input/Output

Network Surge Protection 10/100Base-T Ethernet

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery Type Sealed, maintenance-free lead acid

Average Life 3 - 5 years depending on the number of discharge cycles

and environmental temperature

Physical Net Weight 14.3 lb. (6.5 Kg.)

Size 3.54" (H) x 12.6" (W) x 6.97" (D)

(9.0 x 32.0 x 17.7 cm)

Operating Temperature +32oF to 104oF (0oC to 40oC)

Storage Temperature +5oF to 113oF (-15oC to 45oC)

Operating Relative Humidity 0 to 95% non-condensing

Operating Elevation 0 to 10,000 ft (0 to 3,000m)

Safety and

Regulatory Safety Approvals TUV C-US certified; UL 1778 standard per CSA

standard C22.2 No. 107.1, FCC part 68 &

FCC part 15 Class B, NOM certified

EMC Compliance Notice: This device complies with part 68 and part 15 of

the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any

interference received, including interference that may

cause undesired operation.

“On the bottom of this equipment is a label that contains,

among other information, the FCC registration number

and ringer equivalence number (REN) for this equipment.

If requested, this information must be provided to the

telephone company.”

Model BE650G

The standard warranty is 3 years from the date of purchase. APC’s standard

procedure is to replace the original unit with a factory reconditioned unit. Customers

who must have the original unit back due to assigned asset tags and set depreciation

schedules must declare such a need at first contact with APC Technical Support. APC

will ship the replacement unit once the defective unit is received by the repair

department or cross-ship upon the provision of a valid credit card number. The

customer pays for shipping to APC, and APC pays ground freight transportation costs

back to the customer.

Please DO NOT RETURN Back-UPS ES to the place of purchase under any

circumstances.

1. Consult the Troubleshooting section to eliminate common problems.

2. Verify the battery is connected (see Connect Battery) and that the Circuit Breaker is

not tripped (see Troubleshooting section).

If you still have problems or questions, please contact APC via the internet or at one of

the phone numbers listed below.

3. Before contacting APC, please be sure to record the date purchased, UPS model,

and serial number (on bottom of unit).

4. Be prepared to troubleshoot the problem over the telephone with a Technical

Support Representative. If this is not successful, the representative will issue a Return

Material Authorization Number (RMA#) and a shipping address.

5. Pack the unit in its original packaging. If the original packaging is not available, ask

APC Technical Support about obtaining a new set. Pack the unit properly to avoid

damage in transit. Never use foam beads for packaging. Damage sustained in transit is

not covered under warranty (insuring the package for full value is recommended).

6. Write the RMA# on the outside of the package.

7. Return the unit by insured carrier to the address given to you by APC Technical

Support.

Online Technical Support: http://support.apc.com

http://www.apc.com/support

esupport@apcc.com

Web Site: www.apc.com

USA/Canada: 1.800.800.4272

Mexico: +52.292.0253 / 52.292.0255

Brazil: +0800.12.72.1

Worldwide: +1.401.789.5735

Order Replacement Battery

Replace with an APC qualified battery. Replacement batteries can be ordered from

www.apc.com (valid credit card required). The replacement battery part number for

this Back-UPS is: RBC17.

The battery is disconnected, and either power is unavailable

at the wall outlet, or utility power is having a “brownout” or

an “over voltage” condition.

Surge Protection outlets were overloaded.

Utility power not available at the wall outlet.

Battery is disconnected.

Equipment is connected to the “Surge Protection” outlets.

The Back-UPS ES is overloaded.

PowerChute Personal Edition software has performed a

shutdown due to a power failure.

The Back-UPS ES has exhausted its available battery

power.

Connected equipment does not accept the step-

approximated sine waveform from the Back-UPS ES.

The Back-UPS ES may require service.

The Back-UPS ES is On Battery.

Battery capacity is low (about 2 minutes of use remaining).

Your building wiring presents a shock hazard. Using the

Back-UPS with this condition will void the warranty.

The battery is not fully charged.

Battery is near the end of useful life.

Data line from the ISP or wall outlet is connected to the

wrong jack on the Back-UPS.

Modem has lost AC Power.

Internet connection lost during power outage. Modem lost AC power. Plug the modem’s AC power cord into one of the “Battery Back-up Plus Surge Protec-

tion outlets”.

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	BE650G
Gewicht:	6500 g
Snoerlengte:	1.8 m
Gewicht verpakking:	7500 g
LED-indicatoren:	Ja
Afmetingen verpakking (BxDxH):	445 x 259 x 148 mm
Certificering:	FCC Part 15 Class B/FCC Part 68/TUV/UL 1778
Uitgangsvermogen:	390 W
Accu/Batterij oplaadtijd:	16 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	5 - 95 procent
Gewicht (imperiaal):	14.3 lbs
Bedrijfstemperatuur, bereik:	0 - 40 °F
Hoogte, in bedrijf:	0 - 3000 m
Relatieve luchtvochtigheid bij opslag (geen condensering):	0 - 95 procent
Afmetingen (B x D x H):	320 x 177 x 90 mm
Producten per pallet:	72 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Surge energy rating:	365 J
Nominale input voltage:	120 V
Input-connectietype:	NEMA 5-15P
Output power capacity:	0.65 kVA
Typische backup tijd op halve lading:	13.3 min
Typische backup tijd op volledige lading:	3.7 min
Hot-swap batterij:	Ja
Netspanning, in bedrijf:	120 V
Output-aansluitingen:	8 x NEMA 5-15R