Apc BE550G Handleiding

Apc UPS BE550G

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BE550G (4 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

User Manual Back-UPS

BE550G/BE700G

Caution

• For safety, the Back-UPS ES is shipped with one battery wire disconnected. Small sparks may occur during battery

connection.

• Do not install the unit in direct sunlight, in excessive heat or humidity, or in contact with fluids.

• Connect the power cord directly to a wall outlet; not a surge protector or power strip. The outlet

must be located near the equipment and easily accessible.

Connect the Battery

Overview

Turn on the Back-UPS

Press the ON/OFF switch to turn the unit ON. A single short beep and the green “Power On” indicator confirms that

Back-UPS ES is on and ready to provide protection. The UPS will automatically perform a self-test when power is

applied to the unit, the green LED will flash during the self-test.

Note: Prior to first use, charge the Back-UPS for at least 16 hours to ensure sufficient runtime. The unit is charging

whenever it is connected to utility power, whether the unit is turned ON or OFF.

Master Outlet—Connect a master device, such as a computer. See

“Using the power-saving outlets” on page 2.

Battery Backup and Surge Protection—These outlets receive

power whenever the unit is ON. During a power outage or other

utility problems (brownouts, over-voltages), these outlets will

receive power from the unit for a limited time. Connect a computer,

monitor, and two other data-sensitive devices into these outlets.

Note that one of these outlets is the Master outlet. See “Using the

power-saving outlets” on page 2.

Controlled Outlets—Connect peripheral devices. See “Using the

power-saving outlets” on page 2.

Surge Protection—These outlets provide full-time protection from

surges even if the unit is OFF, but will only supply power when the

unit is ON. Connect a printer, fax machine, scanner, or other

peripherals that do not need battery power during power outages.

Note that if the power-saving feature is enabled, three of these

outlets are controlled by the Master outlet.

Data Port—Use the supplied RJ45/USB cable to connect the Back-

UPS unit to a computer to install the software. See “Install the

PowerChute® Personal Edition software” on page 2.

Circuit Breaker—Push to re-set the circuit breaker.

Modem/Phone/Fax—Connect a DSL or dial-up modem, phone,

fax machine, or 10/100 Base-T ethernet equipment. Note: Do not

connect the UPS telephone protection ports to both the

telephone and network system cables at the same time.

Wall outlet—Connect the unit to a data line wall outlet.

bu0

Back-UPS ES 550 & 750 2

Install the PowerChute

Personal Edition software

Using the supplied USB cable, connect the data port of the unit to the USB port on a computer. Install the

PowerChute Personal Edition software using the enclosed CD.

Power-saving Master and Controlled Outlets

To conserve electricity, configure the Back-UPS to recognize a Master device, such as a desktop computer or an A/V

receiver, and Controlled peripheral devices, such as a printer, speakers, or a scanner. When the Master device goes

into Sleep or Standby mode, or turns OFF, the Controlled device(s) will shut down as well, saving electricity.

Using the power-saving outlets

Note: The Back-UPS ships with the power saving feature DISABLED. To use this feature, the outlets

must be enabled.

Enable the power-saving outlets. Press and hold

ASTER

NABLE

for 2 seconds. The unit will beep to indicate the

feature is enabled. The green LED above the

ASTER

NABLE

button will illuminate.

Disable the power-saving outlets. Press and hold

ASTER

NABLE

for two seconds. The unit will beep to

indicated the feature is disabled. The green LED above the

ASTER

NABLE

button will darken.

Setting the threshold

The amount of power used by a device in Sleep or Standby mode varies between devices. It may be necessary to

adjust the threshold at which the Master outlet signals the Controlled outlets to shut down. When the threshold is set,

the power-saving outlets are enabled.

1.Ensure a master device is connected to the Master outlet. Put that device into Sleep or Standby mode, or turn it

OFF.

2.Press and hold the Master Enable button for six seconds. After the first 2 seconds the unit will beep, continue

holding the button down until the unit three beeps times in a row. Release the Master Enable button.

The Back-UPS unit will now recognize the threshold level of the Master device and save it as the new threshold

setting.

Status Indicators

LED Visual Indicator Audible Alarm Action

Power On - UPS is supplying conditioned utility

power to the load.

Green LED - ON None Not applicable.

On Battery - UPS is supplying battery power to the

load connected to the Battery outlets.

Green LED - ON (off

during beep)

Beeping 4 times

every 30 seconds

UPS transfers back to Power On

operation, or when UPS is

turned off.

Low Battery Warning - UPS is supplying battery

power to the load connected to the Battery outlets and

the battery is near exhaustion.

Green LED - flashing Rapid beeping (every

1/2 second)

UPS transfers back to normal

operation, or when UPS is

turned off.

Replace Battery is in need of charging or is at the end

of its usual life and must be replaced

Green/Red alternating

LED - flashing

Constant tone UPS turned off with the power

switch.

Battery Disconnected - The battery is disconnected or

bad battery.

Red LED - flashing Constant tone UPS turned off with the power

switch.

Overload Shutdown - During On Battery operation a

battery power supplied outlet overload was detected.

None Constant tone UPS turned off with the power

switch.

Sleep Mode - During On Battery operation the battery

power has been completely exhausted and the UPS is

waiting for utility power to return to normal.

None Beeping once every 4

seconds.

Utility power is restored, or if

utility power is not restored

within 32 seconds, or the UPS is

turned off.

Master Function Enabled Master Enable LED -

None

Back-UPS ES 550 & 750 3

Troubleshooting

Master Function Disabled Master Enable LED -

OFF

None

Problem Probable Cause Solution

Back-UPS will not turn on. Battery is disconnected or utility power is

not available at the wall outlet.

Connect the battery and ensure power is available at the wall outlet.

No power available at the Surge

Protection Only outlets.

Surge Protection Only outlets have been

overloaded and disconnected by the circuit

breaker.

Reduce the amount of equipment plugged into Surge Protection Only

outlets and re-set the circuit breaker.

Utility power not available at the wall

outlet.

Ensure the fuse or circuit breaker for the outlet is not tripped, and that

the wall switch controlling the outlet (if any) is in the ON position.

Connected equipment loses power. Equipment is connected to the Surge

Protection Only outlets.

Ensure the equipment you want to stay powered during a power

failure is plugged into the Battery Backup/Surge Protection outlets

and NOT the Surge Protection Only outlets.

The Back-UPS is overloaded. Make sure the equipment plugged into the Battery Backup/Surge

Protection outlets of the unit are not overloading the capacity of the

unit. Try removing some of the equipment and see if the problem

continues.

PowerChute Personal Edition software has

performed a shutdown due to a power

failure.

The Back-UPS is operating normally.

The Back-UPS has exhausted its available

battery power.

The Back-UPS can only operate on battery power for a limited

amount of time. The unit will eventually turn off when the available

battery power has been used. Re-charge for a minimum of 16 hours.

Connected equipment does not accept the

step-approximated sine waveform of the

Back-UPS.

The output waveform is designed for computers and computer-related

equipment. It is not designed for use with motor-type equipment.

The Back-UPS may require service. Contact APC Technical Support.

The Power On indicator is lit and

the Back-UPS is beeping four

times every 30 seconds.

The Back-UPS is using battery. The Back-UPS is operating normally and using battery power. Once

On Battery, you should save your current work, power down your

equipment, and turn the unit OFF. Once normal power is restored, you

may turn the unit back ON and power your equipment.

The Power On indicator flashes

once per second and the Back-

UPS beeps once per second at the

same time.

Battery capacity is low (about 2 minutes of

use remaining).

The Back-UPS is about to shut off due to a low battery charge

condition! When the unit beeps once every second, the battery has

about 2 minutes of power remaining. Immediately power down your

computer and turn the unit OFF. When normal power returns, the unit

will recharge the battery.

Inadequate runtime. The battery is not fully charged. Allow the unit to charge by leaving it plugged into the wall for at least

16 hours.

Battery is near the end of useful life. As a battery ages, the amount of runtime available will decrease. You

can replace the battery by ordering one at www.apc.com. Batteries

also age prematurely if the Back-UPS is placed near excessive heat.

The device connected to the

Master outlet goes into Sleep or

Standby mode, but the equipment

connected to the Controlled

outlets do not turn off.

The “green” function is turned off or the

threshold setting is incorrect.

Re-configure the Master and Controlled outlets. See “Enable the

oulets” on page 2.

The threshold setting of the device

connected to the Master outlet is not

configured properly.

Re-configure the threshold settings of the device connected to the

Master outlet.

Power is not supplied to some

outlets.

The Controlled Outlets may be turned OFF. Disable the Master/Controlled outlets.

The Controlled Outlets are not

supplying power, even though the

Master device is not in sleep

mode.

The Master Outlet threshold may be

incorrectly set.

Re-configure the Master Outlet, ensure the device connected to the

Master Outlet is in sleep or standby mode, or is OFF, when the

threshold is set.

LED Visual Indicator Audible Alarm Action

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	BE550G
Kleur van het product:	Zwart
Gewicht:	5910 g
Snoerlengte:	1.52 m
LED-indicatoren:	Ja
Certificering:	cUL Listed, FCC Part 15 Class B, FCC Part 68, NOM, UL 1778, UL 497A, UL 497B, RoHS
Uitgangsvermogen:	330 W
Accu/Batterij oplaadtijd:	24 uur
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	60 Hz
Afmetingen (B x D x H):	178 x 305 x 89 mm
Bedrijfstemperatuur (T-T):	0 - 40 °C
Nominale input voltage:	120 V
Input-connectietype:	NEMA 5-15P
Output power capacity:	0.55 kVA
Typische backup tijd op halve lading:	13.4 min
Typische backup tijd op volledige lading:	3.2 min
Netspanning, in bedrijf:	120 V
Output-aansluitingen:	8x NEMA 5-15R