Apc BE450G-LM Handleiding

Apc UPS BE450G-LM

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BE450G-LM (6 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Back-UPS® ES 450/550G

User Guide

Connect Battery

Equipment

Turn the Unit On

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS ES is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into these

outlets.

Battery Back-up +Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS ES. Plug your computer,

monitor, and other peripheral devices into the outlets.

Press the ON/OFF switch turn the unit ON.

A single short beep and the green “Power On” indicator confirms

the Back-UPS ES is on and ready to provide protection.

The Back-UPS ES should charge for at least 16 hours to ensure

sufficient runtime. The unit is being charged whenever it is

connected to utility power, whether the unit is turned ON or OFF.

If the red Building Wiring Fault indicator (located on the end near

the power cord) is lit, your building wiring presents a shock hazard

that should be corrected by a qualified electrician.

Install the PowerChute Personal Edition software.

Place the PowerChute CD into the computer and following the

installation instructions on the screen.

.apc.com

The Back-UPS ES indicates operating status using a combination of visual and audible

indicators. Use the following table to identify the status of the Back-UPS ES.

Status

Visual Indications

(Power On - Green)

(Replace Battery -

Red)

Audible Indication Alarm Terminates When

Power On - UPS is supplying

conditioned utility power to the load.

Power On pushbutton

- ON (lit)

None Not applicable.

On Battery - UPS is supplying

battery power to the load connected

to the Battery outlets.

Power On pushbutton

- ON (off during beep)

Beeping 4 times every

30 seconds

UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is

supplying battery power to the load

connected to the battery outlets, and

the battery is near exhaustion.

Power On indicator is

flashing

Rapid beeping (every

1/2 second)

UPS transfers back to

normal operation, or when

UPS is turned off.

Replace Battery - The battery is

disconnected.

The battery is in need of charging, or

is at the end of its usual life and must

be replaced.

Replace Battery

indicator is Flashing

Power On and

Replace Battery

indicators - flashing

(alternating)

Constant tone

UPS is turned off with the

power switch.

Overload Shutdown - During On

Battery operation a battery power

supplied outlet overload was

detected.

None Constant tone UPS is turned off with the

power switch.

Sleep Mode - During On Battery

operation the battery power has

been completely exhausted and the

UPS is waiting for utility power to

return to normal.

None Beeping once every 4

seconds

Utility power is restored,

or if utility power is not

restored within 32

seconds, or the UPS is

turned off.

Building Wiring Fault - Your

building wiring presents a shock

hazard that should be corrected by a

licensed electrician.

Building Wiring Fault

LED (red) - ON

None UPS is unplugged, or

UPS is plugged into a

properly wired outlet.

Status Indicators

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe battery terminal.

NOTE: Small sparks may occur during battery connection. This is normal.

 Turn the Back-UPS ES over and press in the

release tab. Slide the plastic battery cover off of the

Back-UPS.

 Insert the battery back into the compartment.

Slide the plastic battery cover until the release tab

locks into place.

 Connect the battery wire firmly to the

battery terminal.

Connect

Connect Modem / Phone / DSL / Fax

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line - DSL),

Home Phoneline Networking Association (HPNA) type equipment, modem, or fax machines

from surges when connected through the UPS as shown in the drawing below.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not into a surge protector

or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of the operating

system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other end of the cable to

the USB port on your computer. The software will automatically find the computer’s USB Port.

and Install the Software

Transfer Voltage and

Sensitivity Adjustment

(Optional)

To adjust the transfer voltage:

1. Plug the Back-UPS into the utility power source. The Back-UPS

will be in “Standby mode” (no indicators are lit).

2. Press the ON/OFF push button fully in for 10 seconds. The

Online LED will begin glowing in a cyclical order: GREEN-

AMBER-RED, indicating it is going into “Program mode”.

3. The Back-UPS will then indicate the current

sensitivity, as shown in the Transfer Voltage and Sensitivity

Adjustment table below.

4. To select the LOW sensitivity setting, press the ON/OFF push

button until the LED begins

flashing GREEN.

5. To select the MEDIUM sensitivity setting, press the ON/OFF

push button until the LED begins flashing RED.

6. To select the HIGH sensitivity setting, press the ON/OFF push

button until the LED begins

flashing AMBER.

7. To exit Programming mode, once sensitivity is set, wait

approximately 5 seconds, and all of the LED indicators will be

off (unlit).

Indicators

Flashing Sensitivity Setting Input Voltage Range

(For Utility Operation) When to Use

Green

Flashing

LOW 88-142 Input voltage is extremely low or

high.

Not recommended for computer

loads.

Red Flashing MEDIUM

(factory default)

92-139 Back-UPS frequently goes on

battery.

Amber

Flashing

HIGH 96-136 Connected equipment is

sensitive to voltage

fluctuations.

Troubleshooting

Problem Probable Cause Solution

Back-UPS ES will not turn

on.

The battery is disconnected, and either power is

unavailable at the wall outlet, or utility power is

having a “brownout” or an “over voltage”

condition.

Connect the battery (see Connect Battery) and ensure power is available at the wall outlet. If

battery is connected and power is unavailable, the unit can be “cold started” (operated on

battery power) by holding the power button down until two beeps are heard.

No power available at the

Surge Protection outlets.

Surge Protection outlets were overloaded. Reduce the amount of equipment plugged into the Surge Protection outlets.

Utility power not available at the wall outlet. Ensure the fuse or circuit breaker for the outlet is not tripped, and that the wall switch

controlling the outlet (if any) is in the ON position.

Back-UPS is on, but

Replace Battery indicator

flashes, and unit emits a

constant tone.

Battery is disconnected. Connect the battery (see Connect Battery diagram).

Connected equipment

loses power.

Equipment is connected to the “Surge Protection”

outlets.

Ensure the equipment you want to stay powered during a power failure is plugged into the

“Battery Backup plus Surge Protection” outlets and NOT the “Surge Protection Only” outlets.

The Back-UPS ES is overloaded. Make sure the equipment plugged into the outlets of the unit are not overloading its capacity. Try

removing some of the equipment and see if the problem continues.

PowerChute Personal Edition software has

performed a shutdown due to a power failure.

The Back-UPS ES is operating normally.

The Back-UPS ES has exhausted its available

battery power.

The Back-UPS ES can only operate on battery power for a limited amount of time. The unit

will eventually turn off when the available battery power has been used. Allow the unit to

recharge for 16 hours before expecting maximum runtime.

Connected equipment does not accept the step-

approximated sine waveform from the Back-UPS

ES.

The output waveform is designed for computers and computer-related equipment. It is not

designed for use with motor-type equipment.

The Back-UPS ES may require service. Contact APC Technical Support for further troubleshooting.

The Power On indicator is

lit and the Back-UPS ES

beeps four times every 30

seconds.

The Back-UPS ES is On Battery. The Back-UPS ES is operating normally, and using battery power. Once On Battery, you may

want to save your current work, power down your equipment, and turn the unit OFF. Once

normal power is restored, you may turn the unit back ON, and power your equipment.

The Power On indicator

flashes and the Back-UPS

beeps twice per second at

the same time.

Battery capacity is low (about 2 minutes of use

remaining).

The Back-UPS ES is about to shut off due to a low battery charge condition! When the unit

beeps twice every second, the battery has about 2 minutes of power remaining. Immediately

power down your computer ,and turn the unit OFF. When normal power returns, the unit will

recharge the battery.

Building Wiring Fault

indicator is lit.

Your building wiring presents a shock hazard.

Using the Back-UPS with this condition will void

the warranty.

Call a qualified electrician for service.

Inadequate runtime. The battery is not fully charged. Allow the unit to charge by leaving it plugged into the wall at least 16 hours.

Battery is near the end of useful life. As a battery ages, the amount of runtime available will decrease. You can replace the battery

by ordering one at www.apc.com. Batteries also age prematurely if the Back-UPS ES is

placed near excessive heat.

No phone/fax/DSL signal

from the Back-UPS.

Data line from the ISP or wall outlet is connected

to the wrong jack on the Back-UPS. Make sure the data line from the wall outlet is connected to the jack labeled “Wall Outlet”.

Internet connection lost

during power outage.

Modem lost AC power. Plug the modem’s AC power cord into one of the “Battery Back-up Plus Surge Protection

outlets”.

APC Contact Information

Online Technical Support: http://support.apc.com

http://www.apc.com/support

esupport@apcc.com

Web Site: www.apc.com

USA/Canada: 1.800.800.4272

Mexico: +52.292.0253 / 52.292.0255

Brazil: +0800.12.72.1

Worldwide: +1.401.789.5735

Service

Please DO NOT RETURN Back-UPS ES to the place of purchase under any

circumstances.

1. Consult the Troubleshooting section to eliminate common problems.

2. Verify the battery is connected (see Connect Battery) and that the Circuit Breaker is

not tripped (see Troubleshooting section).

If you still have problems or questions, please contact APC via the internet or at one of

the phone numbers listed below.

3. Before contacting APC, please be sure to record the date purchased, UPS model,

and serial number (on bottom of unit).

4. Be prepared to troubleshoot the problem over the telephone with a Technical

Support Representative. If this is not successful, the representative will issue a Return

Material Authorization Number (RMA#) and a shipping address.

5. Pack the unit in its original packaging. If the original packaging is not available, ask

APC Technical Support about obtaining a new set. Pack the unit properly to avoid

damage in transit. Never use foam beads for packaging. Damage sustained in transit is

not covered under warranty (insuring the package for full value is recommended).

6. Write the RMA# on the outside of the package.

7. Return the unit by insured carrier to the address given to you by APC Technical

Support.

Warranty

The standard warranty is 3 years from the date of purchase. APC’s standard

procedure is to replace the original unit with a factory reconditioned unit. Customers

who must have the original unit back due to assigned asset tags and set depreciation

schedules must declare such a need at first contact with APC Technical Support. APC

will ship the replacement unit once the defective unit is received by the repair

department or cross-ship upon the provision of a valid credit card number. The

customer pays for shipping to APC, and APC pays ground freight transportation costs

back to the customer.

Order Replacement Battery

Replace with an APC qualified battery. Replacement batteries can be ordered from

www.apc.com (valid credit card required). The replacement battery part number for

this Back-UPS 450 is RBC 114, and for Back-UPS 550 is RBC 110.

Specifications

Model BE450/550G

Input Voltage 120 Vrms nominal

Frequency 60 Hz + 3

Brownout Transfer 92 Vrms, typical

Over-voltage Transfer 139 Vrms, typical

Output UPS Capacity (4 outlets) 450 VA/550 VA ; 257 W/330 W

Total Amperage (8 outlets) 12 Amps (including UPS output)

Voltage - On Battery 115 Vrms + 8% (step-approximated sine wave)

Frequency - On Battery 60 Hz + 1 Hz

Transfer Time 6 ms typical, 10 ms maximum

Protection and

Filter

AC Surge Protection Full time, 340 joules

Phone/fax/DSL Surge

Protection

Single line (2-wire)

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery Type Sealed, maintenance-free lead acid

Average Life 3 - 5 years depending on the number of discharge cycles

and environmental temperature

Physical Net Weight Back-UPS 450: 10 lb ( 4.5 kg)

Back-UPS 550: 12.4 lb (5.6 kg)

Size 11.2 in (H) x 7.1 in (W) x 3.4 in (D)

(28.2 cm x 18 cm x 8.7cm)

Operating Temperature +32oF to 104oF (0oC to 40oC)

Storage Temperature +5oF to 113oF (-15

oC to 45o

Operating Relative Humidity 0 to 95% non-condensing

Operating Elevation 0 to 10,000 ft (0 to 3,000m)

Safety and

Regulatory

Safety Approvals TUV C-US certified; UL 1778 standard per CSA

standard C22.2 No. 107.3, FCC part 68 &

FCC part 15 Class B, NOM certified

EMC Compliance Notice: This device complies with part 68 and part 15 of

the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any

interference received, including interference that may

cause undesired operation.

“On the bottom of this equipment is a label that contains,

among other information, the FCC registration number

and ringer equivalence number (REN) for this equipment.

If requested, this information must be provided to the

telephone company.”

All other trademarks are property of their respective owners.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

Back-UPS® ES

450/550G

Guía de usuario

Conexión de la batería

Encendido de la unidad e

Protección contra sobrevoltajes

Estos tomacorrientes proporcionan una protección completa contra

sobrevoltajes incluso si el Back-UPS ES se encuentra apagado.

Enchufe en estos tomacorrientes la impresora, máquina de fax,

escáner u otros periféricos que no necesiten energía de la batería.

Energía de la batería +Protección contra

sobretensiones

Estos tomacorrientes estarán alimentados siempre que el Back-

UPS ES se encuentre encendido. Durante un corte de energía u

otros problemas relacionados con la alimentación eléctrica

(bajas de tensión, sobrevoltajes, etc.), el Back-UPS ES

proporcionará energía a los tomacorrientes durante un tiempo

limitado. Enchufe en estos tomacorrientes el ordenador, monitor

y otros periféricos.

Presione el botón de ENCENDIDO/APAGADO para encender

la unidad.

Un solo pitido corto y el indicador verde “Power On” confirman

que el Back-UPS ES se encuentra encendido y listo para

proporcionar protección.

Se deberá cargar el Back-UPS ES durante al menos 16 horas

para asegurar un tiempo de funcionamiento adecuado. La unidad

realizará la carga de la batería siempre que se encuentre

enchufada a la energía eléctrica, independientemente de si se

encuentra encendida o apagada.

Si se enciende el indicador “Building Wiring Fault” (ubicado en el

extremo que está cerca del cable de alimentación), la edificación

presenta un peligro de descarga eléctrica que deberá ser resuelto

por un electricista matriculado.

Instale el software PowerChute Personal Edition.

Coloque el CD de PowerChute CD en el ordenador y siga las

instrucciones de instalación que aparecen en la pantalla.

.apc.com

El Back-UPS ES indica el estado de funcionamiento utilizando una combinación de

indicadores visuales y sonoros. Utilice la siguiente tabla para identificar el estado del Back-

UPS ES.

Estado

Indicaciones visuales

(Power On (Encendido) - Verde)

(Replace Battery (Reemplazar

batería) - Rojo)

Indicación

sonora

La alarma se detiene

cuando

En línea - El UPS está

suministrando energía eléctrica

adaptada a la carga.

Indicador “Power On” –

ENCENDIDO (iluminado) Ninguno. No corresponde.

Funcionando con la batería -

El UPS está suministrando

energía de la batería a la

cargas que se encuentra

enchufada en los

tomacorrientes de la batería.

Indicador “Power On” -

ENCENDIDO (apagado durante

los pitidos)

4 pitidos cada

30 segundos. El UPS regresa al

funcionamiento con energía

eléctrica o cuando el UPS se

apaga.

Advertencia de batería baja -

El UPS está suministrando

energía de la batería a la carga

enchufada a los tomacorrientes

de la batería y la batería está a

punto de agotarse.

Parpadeo del indicador “Power

On”. Pitidos rápidos

(cada medio

segundo).

El UPS regresa al

funcionamiento normal o

cuando el UPS se apaga.

Reemplazar batería - La

batería está desconectada.

Se debe cargar la batería o ésta

llegó al final de su vida útil y

deberá ser reemplazada.

Parpadeo de indicador “Replace

Battery”.

Indicadores “Power On” y

“Replace Battery” - parpadeando

(de forma alternada)

Tono constante.

Se apagó el UPS con el

interruptor de encendido/

apagado.

Apagado por sobrecarga -

Durante el funcionamiento con

la batería, se detectó una

sobrecarga en un tomacorriente

al que se le está proporcionado

energía de la batería.

Ninguno. Tono constante. Se apagó el UPS con el

interruptor de encendido/

apagado.

Modo de espera - Durante el

funcionamiento con la batería,

la carga de la batería se agotó

por completo y el UPS está

esperando que le energía

eléctrica regrese a la

normalidad.

Ninguno. Pitidos cada 4

segundos. Regrese la energía eléctrica,

cuando la energía eléctrica

no haya regresado al cabo

de 32 segundos o cuando se

apague el UPS.

Falla en el cableado de la

edificación - El cableado de la

edificación presenta un peligro

de descarga eléctrica que

deberá ser resuelto por un

electricista matriculado.

Indicador LED “Building Wiring

Fault” (Falla en el cableado de la

edificación) (rojo) - ENCENDIDO.

Ninguno. Se desenchufe el UPS o

cuando se enchufe el UPS a

un tomacorriente de pared

con un cableado correcto.

Indicadores de estado

Por razones de seguridad, se envía el Back-UPS ES con un cable de la batería desconectado. La UPS no funcionará hasta que se conecte el cable al terminal de

la batería seguro al tacto. NOTA: Es posible que se produzcan algunas chispas durante la conexión de la batería. Esto es normal.

Voltee el Back-UPS ES y presione el pestillo de

liberación. Deslice hacia fuera la tapa de

plástico de compartimiento de la batería.

Coloque nuevamente la batería en el

compartimiento. Deslice la tapa de plástico del

compartimiento de la batería hasta que el pestillo

de liberación quede asegurado en su lugar.

Conecte el cable de la batería de

forma firme al terminal de la batería.

Conexión de dispositivos

Conexión de módem / teléfono / DSL / fax

El Back-UPS ES brinda protección contra sobrevoltajes a teléfonos de una sola línea (2

alambres) (incluida la Línea de Suscripción Digital – DSL, por sus siglas en inglés), equipos

HPNA (Alianza de Redes de Líneas Telefónicas Domésticas), módems o máquinas de fax

cuando se encuentran enchufados a través del UPS como se muestra en la ilustración que

aparece abajo.

No exponga el Back-UPS ES a las siguientes condiciones:

- Luz solar directa

- Calor excesivo

- Humedad excesiva o contacto con fluidos

Enchufe el Back-UPS ES directamente en un tomacorriente de pared y no en un

protector contra sobretensiones ni múltiple.

Conexión del cable del ordenador

El cable suministrado y el software proporcionan un almacenamiento automático de archivos

y apagado del sistema operativo en caso de un corte de energía ininterrumpido.

Conecte el cable al puerto Data Port (Puerto de datos) del Back-UPS ES. Conecte el otro

extremo del cable al puerto USB del ordenador. El software buscará automáticamente el

puerto USB del ordenador.

Ajuste de voltaje y

sensibilidad de la

transferencia (opcional)

Para ajustar el voltaje de transferencia:

1. Enchufe el Back-UPS ES a la fuente de energía eléctrica. El

Back-UPS ES ingresará en el “modo de espera” (no se

encenderá ningún indicador).

2. Mantenga presionado el botón de ENCENDIDO/APAGADO

durante 10 segundos. El indicador LED comenzará a parpadear en

un orden cíclico: VERDE-ÁMBAR-ROJO, lo que indica que el

Back-UPS ES ingresará en el “modo de programación”.

3. El Back-UPS ES indicará la sensibilidad actual, como muestra la

tabla Ajuste de voltaje y sensibilidad de la transferencia que

aparece más adelante.

4. Para seleccionar la configuración de sensibilidad BAJA, presione

el botón de ENCENDIDO/APAGADO hasta que el indicador LED

comience a parpadear de color VERDE.

5. Para seleccionar la configuración de sensibilidad MEDIA,

presione el botón de ENCENDIDO/APAGADO hasta que el

indicador LED comience a parpadear de color ROJO.

6. Para seleccionar la configuración de sensibilidad ALTA, presione

el botón de ENCENDIDO/APAGADO hasta que el indicador LED

comience a parpadear de color ÁMBAR.

7. Para salir de modo de programación, una vez que se haya

establecido la sensibilidad, espere aproximadamente 5 segundos

y todos los indicadores LED se apagarán.

Indicadores

LED

parpadeando de

color

Configuración de

sensibilidad

Rango del voltaje de

entrada (para el

funcionamiento con

energía eléctrica)

Se recomienda utilizar esta

configuración cuando

Verde

parpadeando

BAJA 88-142 El voltaje de entrada es

extremadamente bajo o alto. No

recomendado para cargas

pertenecientes a computadoras.

Rojo

parpadeando

MEDIA

(configuración por

defecto de fábrica)

92-139 El Back-UPS ES funciona de forma

frecuente con la batería.

Ámbar

parpadeando

ALTA 96-136 Los equipos conectados son sensibles

a las fluctuaciones en el voltaje.

instalación del software

1 2 3

Product specificaties

Merk:	Apc
Categorie:	UPS
Model:	BE450G-LM
Kleur van het product:	Zwart
Gewicht:	5910 g
Breedte:	305 mm
Diepte:	178 mm
Hoogte:	84 mm
Snoerlengte:	1.52 m
Geluidsniveau:	45 dB
Gewicht verpakking:	6500 g
LED-indicatoren:	Ja
Vormfactor:	Compact
Afmetingen verpakking (BxDxH):	438 x 140 x 241 mm
Aantal USB 2.0-poorten:	1
Certificering:	cUL, FCC p15 B, FCC p68, NOM, UL 1778, UL 497A, UL 497B
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	257 W
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	5 - 95 procent
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Modem (RJ-11) poort:	1
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Type beeldscherm:	LED
Aantal AC uitgangen:	8 AC-uitgang(en)
Nominale input voltage:	120 V
Stopcontacttypes:	NEMA 5–15R
Output power capacity:	0.45 kVA
Ingang operation voltage (min):	- V
Ingang operation voltage (max):	- V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	- V
Netspanning, in bedrijf:	120 V