AMX PDXL-2 Handleiding

AMX Niet gecategoriseerd PDXL-2

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX PDXL-2 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

QUICK START GUIDE

PDXL-2 Dual Power over DXLink Controller

Overview

The PDXL-2 (FG1090-170) is a Power over DXLink injector which allows for remote

powering of any two DXLink devices. The device simplifies installation by allowing the

DXLink Transmitters and Receivers to be placed anywhere even where there are no AC

power outlets—simply install a PDXL-2 in any convenient place within the 100 meter

path to provide power.

The PDXL-2 provides power for DXLink devices by “injecting” power through the twisted

pair cable. The PDXL-2 also accepts I/O control from a NetLinx controller allowing

power down capabilities to either (or both) of the connected DXLink devices to achieve

power savings when the devices are not in use.

Specif ications

The following table lists the specifications for the PDXL-2:

* Cable runs with a minimum specif ication of ANSI/TIE/EIA 568A-5 and ratings of 250

MHz or better (for HD content) and 500 MHz or better (for UHD content) may be used

with DXLink equipment. However, cable run topology and environmental influences can

affect the overall successful distance capabilities of these runs. For successful

deployments up to 100 meters (for HD content) and 80 meters (for UHD content) without

consideration to outside variables, AMX requires the use of shielded Cat6 category cable

(for HD content) and shielded Cat6A category cable (for UHD content) for DXLink runs.

For more details and helpful cabling information, please contact your AMX representative

for a copy of the white paper titled "Cabling for Success with DXLink".

Important Safety Information

• The PDXL-2 should be connected to DXLink devices only. Outside network

connections are not supported.

• Only qualified personnel can install or remove the PDXL-2.

• AC Power Cord Set:

* The power cord must have regulatory agency approval for the specific country

in which it is used (for example, UL, CSA, VDE, etc.)

* The power cord must be a three-conductor type (two current-carrying

conductors and one ground conductor) terminated on one end by an IEC 60320

appliance coupler (for connection to the PDXL-2), and on the other end by a plug

containing a ground (earthing) contact.

* The power cord must be rated for a minimum of 250 VAC RMS operation, with a

minimum rated current capacity of 5 amps or a minimum wire gauge of 18 AWG

(0.75 mm2).

• A PDXL-2 installed in Australia requires power cords with a minimum wire gauge

of 16 AWG (1.0 mm2).

• The PDXL-2 DATA and DATA & POWER ports are shielded RJ45 data sockets. They

CANNOT be used as Plain Old Telephone Service (POTS) telephone sockets. Only

RJ45 data connectors may be connected to these sockets.

• The AC wall socket-outlet must be near the PDXL-2 and easily accessible. You can

remove AC power from the PDXL-2 by disconnecting the AC power cord from

either the wall socket-outlet or the PDXL-2 appliance coupler.

• The PDXL-2 “DATA” and “DATA & POWER” interfaces are qualified as Safety

Extra-Low Voltage (SELV) circuits according to IEC 60950-1. These interfaces

may only be connected to SELV interfaces on other equipment.

• AMX only supports the use of our Enova DGX, Enova DVX, DXLink or Power over

DXLink solutions as the use of any other power supplies or non-compatible

standard PoE solutions may potentially damage the DXLink equipment.

WARNINGS

• The PDXL-2 should only be connected to devices compatible with this product.

Using the PDXL-2 with incompatible devices may cause damage to the device.

• Read the installation instructions before connecting the PDXL-2 to its power

source.

• Follow basic electricity safety measures before connecting the PDXL-2 to its

power source.

• A voltage mismatch can cause equipment damage and may pose a fire hazard. If

the voltage indicated on the label is different from the power outlet voltage, do

not connect the PDXL-2 to this power outlet.

FIG. 1 PDXL-2 DUAL POWER OVER DXLINK CONTROLLER

PDXL-2 Specifications

Active Power Requirements:

Power Connector (1) 100-240V, 50/60 Hz, 1.6A

Power Capabilities • Maximum Current Draw: 1.0A

• Typical Current Draw: 0.35A

Note: Power consumption depends on the device connected to

the DXLink port.

Environmental:

Temperature (Operating) 32° to 104° F (0° to 40° C)

Temperature (Storage) –4º to 158ºF (–20º to 70ºC)

Humidity (Operating) 90%, Non-condensing (maximum)

Humidity (Storage) 95%, Non-condensing (maximum)

Operating Altitude –1000 to 10,000 ft. (–304.8 to 3048 m)

DXLink:

DXLink ports (2) sets of 2 RJ-45 DXLink connectors

Transport Layer

Throughput

10.2 Gbps pass thru

Power over DXLink Output

(per output)

• Pin Assignment & Polarity 4/5 (+), 7/8 (-)

• Output Power Voltage 55 VDC

• Output Power 30 Watts (guaranteed)

• Output Current 0.6 A (maximum)

Indicators:

AC Power Indicator 2 LED (1 for each DXLink Powered Output)

• Yellow (On): power is on and active

• Green (On): A remote terminal is connected

Channel Power Indicator (1) LED green

General:

Dimensions (HWD) 1 7/16” x 7” x 6 13/16” (3.63cm x 17.78cm x 17.24cm)

Weight 2.25 lbs (1.02 kg)

Front Components • AC Power Indicator

• Channel Power Indicator

• DXLink ports

Back Components • (4) 3.5 mm (female) captive-wire connectors. 1 each for:

* Ground

* Relay port 1 (to be fed from I/O connection)

* Relay port 2 (to be fed from an I/O connection)

* +12V power feed

• (1) Power connector

Mounting Options • Rack: MPA-VRK Rack Mounting Tray (FG5968-30)

• Surface: AVB-VSTYLE-SURFACE-MNT Surface Mount

Brackets (FG1010-722)

• Pole: AVB-VSTYLE-POLE-MNT Single Module Pole Mounting

Kit (FG1010-723)

PDXL-2 Specifications (Cont.)

Compatible AMX Products • DXLink HDMI Transmitter Module

• DXLink Multi-Format Transmitter Module

• DXLink Multi-Format Decor Style Wallplate Transmitters (US)

• DXLink Multi-Format Wallplate Transmitters

• DXLink HDMI Receiver Module

• DXLink 4K HDMI Decor Style Wallplate TX

• DXLink 4K HDMI RX

Twisted Pair Cable Type* • Shielded Cat6A minimum for 4K signal support.

• Shielded Cat6 minimum for 1080p and below.

For more details and helpful cabling information, reference the

white paper titled "Cabling for Success with DXLink" available at

www.amx.com or contact your AMX representative.

Twisted Pair Cable

Length*

• Up to 262 ft. (80 m) for full 4K signal support.

• Up to 328 ft. (100 m) for 1080p and below.

Important: DXLink twisted pair cable runs for DXLink

equipment should only be run within a common building.

Certifications • FCC Part 15 Class A

• CE EN 55022 Class A

• C-Tick CISPR 22 Class A

• UL 60950-1

• CE EN 55024

• CE EN 60950-1

• IEC 60950-1

trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their

respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-1090-170 REV: D

Last Revised:4/19/2017

Mounting the Device

The PDXL-2 may be mounted on a flat surface using AVB-VSTYLE-SURFACE-MNT

Surface Mount Brackets (FG1010-722) to mount the device. See the Module Options for

V Styles Modules Quick Start Guide for mounting instructions.

• Use MPA-VRK Rack Mount Brackets (FG5968-30) for a rack mount installation.

• Use the AVB-VSTYLE-POLE-MNT Single Module Pole Mounting Kit (FG1010-723)

for a pole mount installation.

Preliminary Steps

Before placing the PDXL-2:

• Ensure that AC power is applied to the PDXL-2, using an operational ground

connection.

• Connect the incoming DXLink twisted pair connection to the Data port and

connect the twisted pair connection for the DXLink device to be powered to the

Power port.

• Do not cover the device or block the airflow to the device with any foreign objects.

Keep the PDXL-2 away from excessive heat and humidity and free from vibration

and dust.

• Ensure that the cable length from the originating DXLink source to the final

DXLink destination does not exceed 328 feet (100 meters). The device is not a

repeater and does not amplify the DXLink data signal.

• The PDXL-2 does not have a power switch. Simply plug the device into an AC

power source.

Installing the PDXL-2

Perform the following steps to install the PDXL-2:

1. Connect the PDXL-2 to an AC outlet (100-240VAC) using an appropriate power

cord.

2. Connect the DATA & POWER port to a DXLink Transmitter, Receiver, or Wallplate

via the appropriate twisted pair cable.

3. Use an additional twisted pair cable to connect the DATA port to a separate DXLink

Transmitter, Receiver, or Wallplate.

Note: If connecting both DATA & POWER ports to separate devices, use the provided

twisted pair cable to connect the two DATA ports together. Connecting the DATA

ports is not necessary if you are only connecting one DATA & POWER port to

another device.

IMPORTANT: The minimum length from TX to PDXL-2 is 12ft (3.6m). The minimum

length from RX to PDXL-2 is 6ft (1.8m).

eg. TX -> 12ft(min) -> PDXL-2(with 12inch data cable) -> 6ft(min) -> RX

4. (Optional) Connect the PDXL-2 to the I/O port on your Master so you can power

off connected devices. See Powering Off Connected Devices for details.

FIG. 2 displays an example configuration when using only one DATA & POWER port to

power a device. In this example, the RX is powered by the PDXL-2 while the TX is

FIG. 3 displays an example configuration when using both DATA & POWER ports to

power two separate devices:

Pin Connections

FIG. 4 describes the PDXL-2 pin-out connections for the IN and OUT Ports on the front

panel of the device:

Relay Port Wiring

Connecting the PDXL-2 to the I/O port on your Master enables you to power off devices

connected to the PDXL-2. FIG. 5 displays the relay port on the rear panel of the PDXL-2:

Powering Off Connected Devices

The relay port on the PDXL-2 is set to ON by default.

The following diagram (FIG. 6) illustrates how the Relay Port on the PDXL-2 connects to

an I/O port on a NetLinx Master Controller:

• Note that the +12V Power pin on the PDXL-2 is a power input (unlike the relay

connectors on many other AMX products). In this case, the +12V Power (output)

pin on a NetLinx I/O Port connects directly to the +12V pin on the PDXL-2 Relay

Port.

• The RELAY PORT 1 and RELAY PORT 2 pins on the PDXL-2 connect to the pins on

the NetLinx I/O port associated with the devices that will be powered off.

• Also note that a GND-to-GND connection between these connectors is not

necessary.

To turn off power on a DXLink port, you must connect the relay port to an I/O port on a

Master and set the corresponding I/O channel on the Master to ON. For example, to

turn off power on DXLink port 1 (assuming the connection shown in FIG. 6):

ON [dvIO,1]

To turn on Power to DXLink port 1:

OFF [dvIO,1]

Consult the NetLinx Integrated Controllers WebConsole & Programming Guide for more

information on channels and commands.

FIG. 2

WIRING USING ONE DATA & POWER PORT

FIG. 3 WIRING USING BOTH DATA & POWER PORTS

To RX To TX

(not used)

To RX To Wallplate

twisted pair cable

FIG. 4 PDXL-2 PIN-OUT CONNECTIONS

FIG. 5 RELAY PORT

FIG. 6 WIRING DIAGRAM - PDXL-2 RELAY PORT TO NETLINX MASTER I/O PORT

Pins 1/2 (DATA only)

Pins 3/6 (DATA only)

Pins 4/5 (DATA + PWR)

Pins 7/8 (DATA + PWR)

= TransformerNote:

DATA

POWER (+)

POWER (-)

DATA & POWER DATA

GND = Signal Ground

RELAY PORT 2 = Input/Output

RELAY PORT 1 = Input/Output

+12V = Power input

PDXL-2 Relay Port

NetLinx Master I/O Port

PDXL-2 Relay Port

+ 12V

RELAY PORT 1

RELAY PORT 2

NetLinx I/O

Port

+ 12V

I/O Port x

Product specificaties

Merk:	AMX
Categorie:	Niet gecategoriseerd
Model:	PDXL-2
Kleur van het product:	Zwart
Gewicht:	1020 g
Breedte:	177.8 mm
Diepte:	172.4 mm
Hoogte:	36.3 mm
Stroom:	1.6 A
Ingangsspanning:	100 - 240 V
Uitgangsvermogen:	- W
Soort voeding:	Binnen
Temperatuur bij opslag:	-20 - 70 °C
Frequentie:	50/60 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Spanning:	- V
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent