AMX MXD-701 Handleiding

AMX Niet gecategoriseerd MXD-701

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX MXD-701 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

QUICK START GUIDE

MXD-701 7" Modero X Series® G5 Wall/Flush Mount Touch Panel

Overview

MXD-701 7" Modero X Series ® G5 Wall Mount Touch Panels feature the G5 Graphic

Engine as well as a Quad Core Processor. These panels feature edge-to-edge capacitive

touch glass with multi-touch capabilities. They feature advanced technology

empowering users to operate AV equipment seamlessly, while providing the ultimate in

audio and video quality. The MXD-701 is available in Portrait and Landscape layouts:

Product Specif ications

For a full listing of product specifications, refer to the X-Series-G5 Touch Panels MXD/T-

1001 & MXD/T-701 Instruction Manual (available to view/download from

www.amx.com).

MXD-701 Installation

The MXD-701 may be installed directly into a solid surface environment, using either

solid surface screws or the included locking tabs for different mounting options.

• For more detailed installation instructions including important notes on thermal

concerns with Rack and Wall installations, refer to the X-Series-G5 Touch Panels

MXD/T-1001 & MXD/T-701 Instruction Manual (available to view/download from

www.amx.com).

• Detailed specifications drawings for the MXD-701 are available to download from

www.amx.com.

Once installed, the MXD-701 is contained within a clear outer housing known as the

Backbox (FIG. 2). The Backbox is removed to install it into a wall, or when using the

optional Rough-In Box accessory (FG039-18).

Note: For typical mounting surfaces, such as drywall, use the locking tabs as the primary

method for securing the Backbox to the surface. For thin walls or solid surfaces, use

mounting screws (not included).

Power Via PoE

Power for the MXD-701 is supplied via PoE (Power Over Ethernet), utilizing an AMX-

certified, capacitive touch-compliant PoE injector or other approved AMX PoE power

source. The incoming Ethernet cable should be connected to the RJ45 port on the

MXD-701.

Installing the MXD-701 Into a Wall

The MXD-701 comes with a clear plastic Backbox (designed to attach the panel to most

standard wall materials. This Backbox has two locking tabs (one on top and one on

bottom) to help lock the Backbox to the wall.

These locking tabs are only extended AFTER the Backbox is inserted into the wall

(FIG. 3).

• When installing the Backbox, make sure that the assembly is in the correct

position and in the correct place. Once the locking tabs are extended and locked

into place, removing the Backbox may be difficult without having access to the

back of the wall or causing damage to the wall.

• In order to ensure a stable installation of the MXD-701, the thickness of the wall

material must be a minimum of .50 inches (1.27cm) and a maximum of .875

inches (2.22cm). The mounting surface should also be smooth and flat.

Installing the Backbox

For best results, use the included Installation Template (68-5968-04) to ensure proper

placement. The template is marked on one side with directions for both landscape and

portrait installations to ensure that the touch panel and Backbox are properly aligned.

WARNING: Using the Installation Template to select the final placement of the Backbox is

highly recommended. The outside edges of the template are the same dimensions as the

touch panel, which allows you to troubleshoot possible conflicts with wall edges, doors,

and other potential obstacles.

1. Prepare the area by removing any screws or nails from the drywall before

beginning the cutout process.

2. After ensuring proper placement, cut out the mounting surface for the Backbox,

using the (included) Installation Template as a guide.

CAUTION: Making sure the actual cutout opening is slightly smaller than the

provided dimensions is highly recommended. This provides a margin of error if the

opening needs to be expanded. Too little wall material removed is always better

than too much.

3. Thread the incoming Ethernet cable through the surface opening (FIG. 4).

Leave enough slack in the wiring to accommodate any re-positioning of the panel.

4. Remove the Backbox knockouts and thread the incoming wiring through the

knockout holes.

5. Thread the incoming cables from the mounting surface opening and through the

knockouts.

6. Push the Backbox into the mounting surface. Insure that the locking tabs lie flush

against the Backbox and that the Backbox goes freely into the opening.

7. Extend the locking tabs on the sides of the Backbox by tightening the screws

inside the box until snug.

Portrait MXD-701-P FG5968-54

Landscape MXD-701-L FG5968-55

FIG. 1 MXD-701-P/L WALL MOUNT (PORTRAIT AND LANDSCAPE)

MXD-701 SPECIFICATIONS

Dimensions (HWD) • Landscape: 4 13/16" x 7 5/16" x 2 1/2" (122mm x 186mm x 63mm)

• Portrait: 7 5/16" x 4 13/16" x 2 1/2" (186mm x 122mm x 63mm)

Weight 1.4 lbs (0.64 Kg)

Power

Consumption

• Full-On: 11.5W maximum

• Standby: 5.8W

• Shutdown: 1W

• Start-Up Inrush Current: Not applicable due to PoE standard

External Power

Supply Required

Optimal performance requires use of one of the following AMX PoE

power supplies (not included):

• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)

• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)

Certifications • FCC Part 15 Class B

• C-Tick CISPR 22 Class B

• CE EN 55022 Class B and EN 55024

• CB Scheme IEC 60950-1

• IC

• IEC/EN-60950

• UL 60950-1

• RoHS/WEEE compliant

Environmental • Temperature (Operating): 32° F to 104° F (0°C to 40°C)

• Temperature (Storage): 4° F to 140° F (-20°C to 60°C)

• Humidity (Operating): 20% to 85% RH

• Humidity (Storage): 5% to 85% RH

• Power ("Heat") Dissipation:

On: 39.2 BTU/hr

Standby: 19.8 BTU/hr

Included

Accessories

• MXA-USB-C, USB Port Cover Kit (FG5968-18)

• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)

• Installation Template 7”

Sleep ButtonNFC Sensor

Sleep

NFC

Button

MXD-701-L

MXD-701-P

Sensor

FIG. 2 MXD-701 BACKBOX (REAR VIEW)

FIG. 3 MXD-701 (LANDSCAPE)

Locking tab

RJ45 cable clip

RJ45 Cable/Port

Backbox

Backbox knockouts (X4)

Locking tabs (X2)

registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks

of their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-5968-54 REV: E

Last Revised: 6/22/2015

Apply enough pressure to the screw head to keep the box flush with the wall: this

ensures that the locking tabs will tighten up against the inside of the wall. The

Backbox is clear to allow visual confirmation that the tabs have been extended

and are gripping the wall, as well as in assisting with removal if necessary.

Note: The maximum recommended torque to screw in the locking tabs on the

Backbox is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the tab

screws, such as with powered screwdrivers, can strip out the locking tabs or

damage the Backbox.

8. For additional strength, #4 mounting screws (not included) may be secured via

mounting holes located at the left and right sides of the MXD-701 (FIG. 4).

In order to prevent damage to the touch panel, make sure that these are flush

with the Backbox.

9. Insert each connector into its corresponding location along the back of the

device. To reach the RJ45 connector, gently pull it from beneath the electronics

cover. Attach the Ethernet cable and gently push the connection back under the

cover.

Note: To facilitate connection of the RJ45 connector to the Ethernet cable, press the

RJ45’s cable into the RJ45 cable clip to hold it in a stable position. Make sure to

remove the cable from the cable clip before continuing the rest of the installation.

10. Test the incoming wiring by attaching the panel connections to their terminal

locations and applying power. Verify that the panel is receiving power and

functioning properly to prevent repetition of the installation.

Note: Do not disconnect the connectors from the touch panel. The unit must be

installed with the attached connectors before being inserted into the mounting

surface.

Remove power before continuing with the installation.

11. Latch the panel onto the top hooks on the Backbox and push it down (Landscape)

onto the bottom snaps or on the left side and push it to the right (Portrait)

(FIG. 5).

Press gently but firmly on the ends until the snaps “click” to lock it down.

WARNING: If you see a gap between the panel and the Backbox, or feel any binding while

locking down the panel, stop immediately and verify that no cables or other items are in

the way. Do not force the panel into position, as this can cause damage to the touch

screen or the panel electronics.

12. Reconnect the terminal Ethernet and USB to their respective locations on the

Ethernet port.

Powering On/Off X Series G5 Panels

Modero X Series G5 touch panels may be powered on by touching and holding the Sleep

button. To power off the panel, press and hold the Sleep button, and select Power Off

on the on-screen menu (FIG. 6):

Conf iguration and Programming

X Series G5 touch panels are equipped with a Settings menu that provides the ability to

configure various features on the panels.

To access the Settings menu, press and hold the Sleep button, and select Settings.

Note: Information on the Settings menu, panel configuration, and programming is

provided in the Modero X Series G5 Programming Guide, available at www.amx.com.

Setting the Panel’s Device Number and Device Name

1. In the Settings menu, select NetLinx. This opens a password keypad.

2. Enter the panel password into the keypad (the default is 1988) and select OK to

access the NetLinx page.

3. Press Device Number to open the NetLinx editing window.

4. Enter a unique Device Number assignment for the panel and press OK.

5. Enter a unique Device Name assignment for the panel and press OK.

Conf iguring the Panel’s IP Address

These steps configure the panel to communicate with a network; it is still necessary to

connect to the NetLinx Master (see Connecting to a NetLinx Master below).

Network Communication via DHCP

1. In the Ethernet page, press DHCP/Static field to open the DHCP/Static window.

Note that DHCP is the default setting.

2. Select Host Name, enter the new host name

3. Press OK to save changes.

Network Communication via Static Address

1. In the Ethernet page, press DHCP/Static to open the DHCP/Static window.

2. Select Static to open the Static IP window.

3. Press any field to open a keypad or keyboard (depending on the field), and enter

the appropriate network address information.

4. Press OK to save your changes and return to the Ethernet page.

Connecting to a NetLinx Master

To establish the type of connection to make between the panel and the NetLinx Master:

1. In the NetLinx page, press Mode to choose the connection mode (URL, Listen or

Auto):

2. If password security is enabled on the target Master, enter the Username and

Password:

a. Select Username to open the NetLinx window.

b. Enter the Username and Password required by the Master.

c. Press OK to save changes and return to the NetLinx page.

Related Software and Additional Documentation (at www.amx.com)

• Programming the Modero X Series G5 touch panels requires the use of the latest

versions of NetLinx Studio and TPDesign5, both available to download at

www.amx.com. Refer to the NetLinx Studio and TPDesign5 online help for

information.

• For information on designing touch panel pages intended to optimize the Modero

X Series G5 experience, refer to the G5 Considerations Guide.

• For additional information on the MXD-701 panel, refer to the X-Series-G5 Touch

Panels MXD/T-1001 & MXD/T-701 Instruction Manual.

• For detailed information on the Settings menu as well programming information

and instructions on upgrading firmware, refer to the Modero X Series G5

Programming Guide.

FIG. 4 MXD-701 BACKBOX INSTALLATION (LANDSCAPE)

FIG. 5 INSTALLING THE MXD-701

#4 Screws

2X Installation Clamp

for Wall Thickness

.37 [12.03] to .98 [.25.0]

4X Knock-Outs

Remove for Cable

Routing as Needed

Mounting Surface

Backbox

Latch Hooks

Snaps

FIG. 6 SLEEP BUTTON - PRESS AND HOLD TO ACCESS POWER OFF/SETTINGS OPTIONS

CONNECTION MODES

Mode Description Procedures

URL The device connects to the

target Master’s IP address

via a TCP connection.

1) Select URL in the Mode menu.

2) Enter the Master IP/URL, Master Port Number, and

Username/Password (if required by the Master).

Press OK to save changes.

Listen This mode allows the panel

to “listen” for the Master’s

communication signals.

Note that in this mode, the

System Number and Master

IP/URL fields are read-only.

1) Select Listen in the Mode menu.

2) Confirm the panel’s IP address is on the Master’s

URL list (via NetLinx Studio).

3) Press OK to save changes.

Note: The Host Name (set on the Ethernet page), can

be used to locate the panel on the Master (useful for

DHCP connections where the IP address can change).

Auto Use this mode when both

the panel and the NetLinx

Master are on the same

Subnet.

1) Select Auto in the menu.Mode

2) Enter the System Number and Username and

Password (if applicable).

3) Press OK to save changes.

Product specificaties

Merk:	AMX
Categorie:	Niet gecategoriseerd
Model:	MXD-701

Heb je hulp nodig?

Als je hulp nodig hebt met AMX MXD-701 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd AMX

AMX HydraPort HPX-1600 Handleiding

19 November 2024

AMX HPX-900 Handleiding

12 November 2024

AMX HPX-1200-NA Handleiding

12 November 2024

AMX HPX-600-NA Handleiding

12 November 2024

AMX HPG-10 Handleiding

12 November 2024

AMX HPX-900-NA Handleiding

12 November 2024

AMX HPX-MSP-7-SL Handleiding

22 Augustus 2024

AMX HPX-MSP-10-SL Handleiding

22 Augustus 2024

AMX TPC-WIN8-TAB Handleiding

8 Juli 2024

AMX NMX-DEC-N1222A Handleiding

20 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic NB-W250 Handleiding

25 November 2024

Alpine CHM-S611 Handleiding

25 November 2024

AOpen DE3650-C Handleiding

25 November 2024

Lazer Urbanize MIPS Handleiding

25 November 2024

Symmons Dia 353GB-24 Handleiding

25 November 2024

SoundTube IPD-RS62-EZ Handleiding

25 November 2024

Moen Camerist 4905 Handleiding

25 November 2024

Lazer Cameleon DLX Handleiding

25 November 2024

DMT DLD-85 Handleiding

25 November 2024

AOpen AM1120T Handleiding

25 November 2024