AMX MXA-FMK-43 Handleiding

AMX Niet gecategoriseerd MXA-FMK-43

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX MXA-FMK-43 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 699 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

QUICK START GUIDE

MXA-FMK-43 Modero X Series® Flush Mount Kit

Overview

The MXA-FMK-43 Flush Mount Kit (FG5968-72) mounts the MXD-430 Modero X 4.3”

Wall Mount Touch Panel flush with the wall. Once installed, simply press lightly on the

touch panel and the spring-loaded mechanism extracts the panel just slightly for

access to the side buttons and enhanced speaker exposure.

This document describes a standard wall installation of the MXA-FMK-43 Flush Mount

Kit. For details on Installation Options for solid wall placement, refer to the MXA-FMK-

43 Solid Wall and Rough-In Box Installation Quick Start Guide.

Installation of the Flush Mount Kit

The MXA-FMK-43 Flush Mount Kit (“FMK”) is designed to attach the panel to most

standard wall and solid surface materials. The FMK has two locking tabs (one on each

side) to help lock the FMK to the wall.

• These locking tabs are only extended AFTER the Flush Mount Kit is inserted into

the wall.

• Using the locking tabs is highly recommended for standard mounting surfaces

such as walls.

WARNING: When installing the Flush Mount Kit, make sure that the assembly is in the

correct position and in the correct place. Once the locking tabs are extended and

locked into place, removing the Flush Mount Kit may be diff icult without having

access to the back of the wall or causing damage to the wall.

Note: In order to guarantee a stable installation of the MXA-FMK-43, the thickness of the

wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875 inches

(2.22cm). The surface should also be smooth and flat.

1. After ensuring proper placement, cut out the mounting surface, using the MXA-

FMK-43 Cutout Template (68-5968-08) as a guide (FIG. 1).

CAUTION: The cutout dimensions shown will allow the unit to pass through without any

dragging or interference. The outer (dotted) lines show the perimeter of the mounting

flange. If any part of the cutout extends up to or beyond that perimeter, the cut edge will

be visible after installation, or the unit could fall through the opening.

A larger cutout reduces the available surface to support the unit when mounted, so the

cut should be as close to the indicated dimensions as possible. If the cutout is too small,

forcing the unit into place could result in mechanical binding, faulty operation, or damage

to the product. Always check for a proper fit before f inal installation.

2. Remove the knockout at the bottom right of the FMK, and thread the incoming

wiring through the knockout hole (FIG. 2).

3. Thread the incoming Ethernet wiring through the surface opening and through

the knockout.

4. Push the FMK flat into the mounting surface and secure with the locking tabs

(FIG. 3).

5. In order to prevent damage to the touch panel, make sure that any screws used

are flush with the FMK, and the FMK goes freely into the opening.

WARNING: The maximum recommended torque to screw in the locking tabs on the

plastic Flush Mount Kit is 5 IN-LB [56 N-CM]. Applying excessive torque while

tightening the tab screws, such as with powered screwdrivers, can strip out the

locking tabs or damage the plastic.

6. Insert each connector into its corresponding port on the back of the touch panel.

For more information, please refer to the Modero X Series G4 Touch Panels

Instruction Manual.

7. Test the incoming wiring by attaching the panel connections to their terminal

locations and applying power. Verify that the panel is receiving power and

functioning properly to prevent repetition of the installation.

Note: Do not disconnect the connectors from the touch panel. The unit must be

installed with the attached connectors before being inserted into the drywall.

PRODUCT SPECIF ICATIONS

Dimensions (HWD): 5.68” x 4.21” x 3.25” (14.43 cm x 10.69 cm x 8.25 cm)

Weight: 0.55 lbs (0.25 kg)

Included Accessories: • MXA-FMK-43 Cutout Template

• MXA-FMK-43 Drilling Template

• Mounting Screws (2) - #8-32 X 1.25", PPH, Black

• Spacers (2)

• Push-on Retainers (2) - #8, Nylon

Other AMX Equipment: • CB-MXP-43-F Flush Mount Rough-In Box/Cover Plate

(FG5968-82)

FIG. 1 MXA-FMK-43 CU TOUT TEMPLATE

5.00”

(12.69 cm)

3.52” (8.95 cm)

Perimeter of Flush

Note: Cut additional tabs

Mount Kit flange

on each side to allow room

for locking tabs.

FIG. 2 INSERTING THE MXA-FMK-43 INTO THE WALL SURFACE

FIG. 3 LOCKING TAB LOCATION ON THE MXA-FMK-43

Wall Surface

MXA-FMK-43

Locking Tab

Knockout

Locking Tab Screw

Use a screwdriver

or other flat tool

to hold the lower

edge of the back

box above the

case while snapping

down the touch panel.

are registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered

trademarks of their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-5968-72 REV: D

Last Revised: 3/10/2016

8. Snap the panel onto the FMK snaps (FIG. 4) by pressing gently but firmly and

evenly on the defined surface areas of the glass until the panel snaps “click” to

lock it down..

Using the MXA-FMK-43

Once the touch panel is installed in the MXA-FMK-43, the panel may be extended from

the wall for enhanced speaker and microphone exposure and to access the panel’s

Sleep/Setup button. To extend the panel from the Flush Mount Kit, press gently on both

sides of the panel’s surface until you hear or feel a “click”. Release the panel to extend

it.

To return the touch panel to its flush position, press again gently on both sides of the

panel’s surface, on the black border on the edge of the panel, until you hear or feel a

“click”. When you release the panel’s surface, the panel will remain in its flush position.

Removing the Touch Panel From the MXA-FMK-43

The touch panel may only be removed from the MXA-FMK-43 when the touch panel is

extended from the wall. For more information on uninstallation of the touch panel in

question, please refer to the Modero X Series G4 Touch Panels Instruction Manual.

A Note About Wall and Rack Installation

Some products are installed in areas of differing temperature and cooling

methodologies. These include products installed in walls, racks, cabinets, etc. Those

areas may have different temperatures and/or cooling approaches that must be taken

into consideration t o maintain the product within the specified operating temperature.

FIG. 5 shows an AMX device installed in a wall with a filled volume (such as with

insulation or concrete), as well as with a closed volume (such as between studs in

an otherwise finished wall). The diagram shows how heat generated by the device

or other devices may have no way to escape, and may build up to levels that may

affect device operation.

In FIG. 6, the diagram displays an AMX device in a typical rack mounting, with full

air circulation around the front and back of the device. In this case, the main

concern is with heat building up between components, possibly to levels that may

affect device operation.

Installation Recommendations

During any installation, a lack of ventilation may produce conditions that may adversely

affect the device’s operation. In these circumstances, special care must be made to

make sure that temperatures within enclosed areas do not exceed the device’s

maximum rated temperature.

Additional Documentation

Refer to the MXA-FMK-43 product page at www.amx.com for detailed pictorial, template

and mounting specifications drawings.

For details on solid wall placement options for the MXA-FMK-43, refer to the MXA-FMK-

43 Solid Wall and Rough-In Box Installation Quick Start Guide.

FIG. 4 INSERTING THE MXA-FMK-43 INTO THE WALL SURFACE

Top Snap

Bottom Snaps

Press Here to

Panel snaps at the top and bottom simultaneously

Snap onto FMK

FIG. 5 Heat convection in filled or closed volume, limited or no convection

FIG. 6 Heat convection in rack-mounted devices

Product specificaties

Merk:	AMX
Categorie:	Niet gecategoriseerd
Model:	MXA-FMK-43
Kleur van het product:	Zwart
Montagewijze:	Muur
Compatibiliteit:	MXD-430
Aantal displays ondersteund:	1