AmpliVox S505A Handleiding

AmpliVox Multimedia kar S505A

Lees hieronder de 📖 handleiding in het Nederlandse voor AmpliVox S505A (2 pagina's) in de categorie Multimedia kar. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

4 1

3995 COMMERCIAL AVE., NORTHBROOK, IL 60062

AMPLIVOX PORTABLE SOUND SYSTEMS

PH. 800-267-5486 OR 847-498-9000

FX. 800-267-5489 OR 847-498-6691

WEB: WWW.AMPLI.COM

EMAIL: CUSTOMERSERVICE@AMPLI.COM

Made in USA

TRANSMITTER

MIC INPUT JACK

POWER ON INDICATOR

POWER ON/OFF SWITCH

CHANNEL SELECTOR SWITCH

1) Switch the Frequency Selector Switch to the desired channel (A or B).

2) Belt clip on the back of the unit clips the transmitter onto a belt or the

transmitter simply can be put into a pocket.

3) Plug the microphone into the Mic Input Jack.

4) The microphone can be clipped to a necktie or other clothing, using

the supplied clip. The lapel mic should be placed under the chin, as

close to the center of the body as possible

5) Slide the power ON/OFF switch to the ON position (the LED indicator

light will illuminate).

HELPFUL HINTS

A) If the selected channel is noisy, switch both the transmitter and

receiver to the other channel.

B) Low ceiling fluorescent lighting, overhead telephone lines, or close

proximity to metal fences can all cause static. If this occurs, try a

slight change of position and/or try changing frequencies.

WIRELESS MIC SET UP

The VHF wireless microphone system is compact, lightweight and

compatible with all AmpliVox VHF wireless systems. The wireless mic

operates in an authorized VHF band and has a useful range of up to 300-

ft. Each system operates on two crystal-controlled, switch selectable

frequencies for clear clean transmission.

“A” Channel “B” Channel

T6: 171.105 MHz T7: 171.845 MHz

The frequency appears on the back of each unit. Both transmitter and

receiver must have the same, and both units must be set to either “A” or

“B.” Note that two transmitters on the same frequency will not work with

one receiver. However two or more receivers will work with the same

transmitter. Before use, make certain you understand the function and

operation of the system.

RF INTERFERENCE

Please note that wireless frequencies are shared with other radio

services. According to the Federal Communications Commission

regulations, “Wireless microphone operations are unprotected

from interference from other licensed operations in the band. If any

interference is received by any Government or non-Government

operation, the wireless microphone must cease operation…” If you need

assistance with operation of frequency selection, please contact your

dealer or AmpliVox. Additionally There are models available for use in

Canada.

POWER SOURCE

The transmitter and receiver are each operated by a 9V alkaline battery.

Before use, install a battery as shown. Make certain the battery is fully

seated in its compartment so the cover slides in place easily. Battery life

with alkaline batteries is approximately 8 hours of operating time. The

receiver also features an external jack for connecting a 9V DC power

supply (not included).

TRANSMITTER OPERATION

If there is a “dead spot” in a room, try a slight change of position or try

changing frequencies. Each unit provides two selectable transmitting

frequencies.

9V DC ALKALINE

BATTERY

RIBBON FOR

BATTERY REMOVAL

BATTERY COVER

C) When the battery voltage drops below 6V, the LED indicator will

go out. This means you need a new battery.

D) Be sure to turn off the power whenever the units are not in use,

and remove the batteries if the units will be out of service for a

long time. NOTE: There are no user-adjustable parts inside the

transmitter or receiver Do not attempt to open or make any adjustments

E) Cellular telephones cause interference. Ask your audience to turn off

their cell phones.

BELT CLIP

A detachable belt clip is included for convenience. Slide the tapered

end of the belt clip into the grooved area located on the back of the unit

until it clicks into place.

PROBLEM SOLVING

FEEDBACK

Feedback is the howl or screech often heard in sound reinforcement

systems. It is caused by sound from the loudspeaker returning to the

microphone. AmpliVox systems utilize proven acoustical principles

to minimize this; however, there is no way to completely eliminate

feedback under conditions of high amplification. If feedback occurs

check the following:

1. User’s hand covering the head of the microphone. (Hold microphone

under head slots.)

2. Sound can easily re-enter microphone. Keep loudspeaker turned

toward audience. Note: sound can be reflected from a hard surface

back through the microphone. (Turn speaker.)

3. User holding microphone in a reflecting position. (Turn microphone.)

4. Volume setting too high. (Reduce microphone channel volume;

compensate by speaking louder or closer to the microphone.)

NO SOUND

Make sure amplifier POWER switch is turned on and red LED is lit. If

switch is on and LED is not lit, check to see that batteries are properly

connected and at full charge. If using optional power adapter, check to

see that front panel connector is properly seated, and verify that power

source is live.

IF YOU HAVE ANY QUESTIONS OR PROBLEMS PLEASE CALL OUR

CUSTOMER SERVICE DEPARTMENT AT 1-800-267-5486

Thank you for choosing the S505A and SW505A

Executive Adjustable Lectern from AmpliVox

Portable Sound Systems. Our system combines

flexibility with functionality. Please refer to this

user guide as you enjoy the unique capabilities of

another quality product from AmpliVox Portable

Sound Systems. As always, you can reach us at

800-267-5486, or at 847-489-9000, Monday -

Friday 8am - 6pm CST.

USER GUIDE

TABLE OF CONTENTS .................................................1

ASSEMBLY OF LECTERN (NO TOOL ASSEMBLY) ..2

CONTROL PANEL ........................................................3

WIRELESS MIC SETUP ..............................................4

PROBLEM SOLVING ..................................................4

NEED HELP?

CALL 800-267-5486

OR 847-498-9000

EMAIL:

CUSTOMERSERVICE@

AMPLI.COM

Made in USA

EXECUTIVE ADJUSTABLE SOUND COLUMN LECTERN S505A / SW505A

WHAT’S IN THE BOX?

NEVER RUN OUT OF

POWER GUARANTEE!

AMPLIFIER POWER SOURCES

(SOLD SEPARATELY)

10 D-CELL ALKALINE

BATTERIES FOR UP TO

200 HOURS TALK TIME

S1460 INTERNATIONAL

AC ADAPTER/RECHARGER

(110/240V; 50/60HZ)

S1465 NICAD

RECHARGEABLE BATTERY

PACK (REQUIRES S1460).

S505A

S805A Multimedia Stereo Amplifier

Dynamic XLR Microphone

15 foot XLR mic cable

Flexible Gooseneck with Shock

Mount Isolated Mic Holder

2 Built in Speakers

4 Neural Knobs/screws for

Reading Table 1" knob, 1" long

4 Neural Knobs for Base 2" long

Speaker Grille Cover

SW505A

SW805A Multimedia Stereo Amplifier

w/Internal Wireless Receiver

Dynamic XLR Microphone

15 foot XLR mic cable

Flexible Gooseneck with Shock

Mount Isolated Mic Holder

Wireless Mic and Transmitter

2 Built in Speakers

4 Neural Knobs/screws for

Reading Table 1" knob, 1" long

4 Neural Knobs for Base 2" long

Speaker Grille Cover

2 3

NEED HELP?

CALL 800-267-5486

OR 847-498-9000

EMAIL:

CUSTOMERSERVICE@

AMPLI.COM

NO TOOL ASSEMBLY OF LECTERN

SPEAKER COVER / AMPLIFIER

8. Remove and unpack the speaker cover.

9. Attach the speaker cover to the front of

the shroud by pushing the plastic posts in

each corner of the cover into the rubber

receptacles in the front of the shroud. See

figure 4 and 5.

Please read all instructions first and then follow the steps below:

BASE ASSEMBLY

1. Remove center column and shroud assembly from the shipping

carton and place as shipped (face down) on the floor or on a suitable

sturdy table.

2. Remove and unpack the base from the shipping carton.

3. Assemble the base to the column as shown in FIGURE 1 by using four

of the 2 inch long neural knob screws supplied with the lectern.

TIP: Do not completely tighten each screw as you place it through the

base and into the column. Wait until all four screws have been put into

the proper position and then tighten them up.

4. Turn the base and column assembly upright. If assembled on a table

place the unit upright on the floor.

READING TABLE ASSEMBLY

5. Remove and unpack the lectern reading table.

6. Attach the table to the top of the column. See FIGURE 2. This is

accomplished by placing the table top on the column base and lining

up the corners.

TIP: the corners need to be lined up in order to get the screws in the

table top.

7. Fasten the reading table to the colum with the 4 1 inch long neural

knob screws supplied. The knob screw goes up into the reading table

throught the 4 holes in the column (see ).FIGURE 2

FIGURE 1

FRONT VIEW

FIGURE 2

BASE

CENTER

COLUMN

READING

TABLE

CENTER

COLUMN

INSTALL NEURAL

KNOBS FROM

BASE INTO

COLUMN

THE CORNERS NEED TO

BE LINED UP IN ORDER

TO GET THE SCREWS IN

THE TABLE TOP.

10. Flush mount ampifier is built-in.

11. For an optional speaker installation (S1201) make sure the speaker

connection cable is routed through the proper notch in the back face of

the amplifier pocket of the shroud so that the table will not pinch the

cable when mounted. See .FIGURE 3

12. (SW505A) Make sure the antenna cable is also routed through the

notch in the same manner.

13. SW505A ONLY - Insert the small (2.5mm) plug into the amplifier

jack labeled ‘Antenna.’

14. See the amplifier operation manual for further instructions regarding

operation of the sound system.

OPERATION OF ADJUSTABLE LECTERN

This lectern adjusts from 39 inches to 45 inches measured from the

Amplifier side. To adjust the lectern height:

1. With one hand flat in the center of the table holding it down loosen

the adjustable height knob with the other hand.

2. You may extend the lectern up to its maximum height of 45 inches.

3. To lower the lectern, lightly press down on the reading table until the

desired height is reached and retighten the height-locking knob.

TIP: The knob locks at any height by tightening it. The lectern will adjust

from 45 inches down to 39 inches when measured from the amplifier

side.

ASSEMBLY OF FLEXIBLE GOOSENECK: (FIGURE 3)

To install the located 1. GOOSENECK onto the 2. MOUNTING FLANGE

by the far left corner of the desktop reading surface, first turn the neck

piece clockwise onto the mount. Next install the microphone holder (U

shaped piece) onto the end of the gooseneck by turning it clockwise

onto the top of the neck. You can then slide the 3. MICROPHONE into

the as shown. 4. MICROPHONE HOLDER

The 5. MIC CORD has a plug with three small holes in one end, A for

connecting with the microphone, and a ¼ in. male plug on the other

end, B for connecting with the unit on the control panel. Connect the

end with the three holes to the base of the microphone, and plug the

male ¼ in. end of the microphone cord into the jack labeled DYNAMIC.

The microphone has an ON/OFF switch . it should always be in the OFF

position until the main power is ON and you are ready to speak.

TO INSTALL OR REPLACE BATTERIES

Remove all cables and plugs from amplifier. Unscrew the thumb screws.

Pull carriage out to install new batteries, Insert 10 new Alkaline “D”

cell batteries, be sure to observe polarity, or replace with S1465 NiCad

battery pack. Carefully replace battery carriage. Reattach battery

door.

TIP:

Do not mix battery types or attempt to recharge alkaline batteries

- equipment damage, safety hazard or fire could result.

OPTIONAL POWER SUPPLY INSTALLATION

Optional Power Supplies may be substituted. Model S1460, International

AC Adapter/Recharger (110/220V, 50/60Hz). Model S1462, 12 Volt

DC adapter (automotive cigarette lighter plug-in). S1465 NiCad Battery

Pack.

5. MIC

CORD B

1. FLEXIBLE

GOOSENECK

4. SHOCKMOUNT MIC

HOLDER

2. MOUNTING

FLANGE

3. MICROPHONE

5. MIC CORD A

BASE

CENTER

COLUMN

READING

TABLE

TO OPERATE:

Plug microphone into DYNAMIC Microphone jack.

Plug straight end of 12” speaker cable into built in speaker jack and

right angle end into left SPEAKER jack on amplifier.

Turn Amplifier on (switch is located on the front of the amplifier). The

red light will go on, showing that power is available. Rotate VOLUME

control knob to obtain desired loudness level throughout the coverage

area.

MICROPHONE VOLUME

Controls the volume level of the microphones, including the wireless

microphones.

MICROPHONE INPUTS

There are three microphone inputs, which can be used

simultaneously:

DYNAMIC - for standard dynamic microphones 1/4 in.

CONDENSER - for electret or condenser microphones, which require

phantom power (supplied from the amplifier) 3.5mm

WIRELESS - accepts output from an external wireless microphone

receiver

AUXILIARY

The LINE IN provision is for connecting an external audio source such

as a CD player, tape player, MP3 player or computer sound card This

input also serves as a provision for connecting additional wireless

microphone receivers, audio mixers and other line level audio

sources.

Separate VOLUME and TONE control knobs allow flexibility in

controlling the sound quality as well as balancing the auxiliary source

with the microphones.

OUTPUT

The LINE OUT provision may be used for connecting to an input on

a recording device, such as a computer sound card, MP3 recorder,

tape recorder, or similar device. The LINE OUT can also be used

for a number of other applications, such as connecting to a house

system, or connecting to one of our wireless speaker transmitters,

for example.

INTERNAL SPEAKERS

The internal speakers are wired for stereo, LEFT and RIGHT channel

information is reproduced by the appropriate speaker inside the

unit.

EXTERNAL SPEAKERS

Two separately amplified speaker jacks allow you to use one or two

S1201, S1290, or any of our horn speakers for additional sound

power. Note: when using a stereo AUX source with a single speaker,

only one of the stereo channels will be heard. However, all MIC inputs

are heard equally on both channels.

IINTERNAL WIRELESS MICROPHONE RECEIVER *SW Model only*

Power ‘ON’ and ‘OFF’; Frequency ‘A’ and ‘B’ switches. Frequency

should match wireless transmitter. The red light above these switches

will come on when the wireless microphone receiver is active.

TONE L - SPEAKER - RVOLUMEDYNAMICVOLUME

WRLS 1

LINE IN

WIRELESSCONDENSER

LINE OUT

OFF

E X T E N D Y O U R V O I C E W I T H

1-800-267-5486

WWW.AMPLI.COM

MADE IN USA

OFF

AUX OUTDC IN

MAIN

POWER MICROPHONES AUXILIARY OUTPUT

MAIN

POWER

SWITCH

INTERNAL

WIRELESS MIC

RECEIVE RS

MASTER

VOLUME

MIC

INPUT

MIC

INPUT

MIC

INPUT

LINE IN

JACK

LINE OUT

JACK

SPEAKER

JACKS

TONE

CONTROL

AUXILIARY

VOLUME

POWER

INPUT

AUX

OUT

ON-OFF

When switch is in the ON position, the red light

will be on.

DC IN

Connection for optional adapter:

S1460 Universal AC Adapter (110/220V,

50/60Hz)

S1465 Nicad Battery Pack (requires S1460 AC

Adapter/recharger)

AUX OUT

Power source for 12 to 15V DC accessories.

S505A & SW505A CONTROL PANEL

AMPLIFIER

ADJUSTABLE

HEIGHT DIAL

USE TO ADJUST

LECTERN

HEIGHT FROM

39 TO 45 INCHES

STORAGE

SPAGE FOR

OPTIONAL

S1201

SPEAKERS

FIGURE 3

BATTERY PANEL

TO INSTALL

OR CHANGE

BATTERIES,

REMOVE THUMB

SCREWS AND

PULL OUT

CARRIAGE.

Product specificaties

Merk:	AmpliVox
Categorie:	Multimedia kar
Model:	S505A
Kleur van het product:	Walnoot
Gewicht:	34019.5 g
Breedte:	635 mm
Diepte:	482 mm
Hoogte:	1143 mm
Soort:	Multimedia-standaard
Uitgangsvermogen:	50 W