Amewi Trix 25307 Handleiding

Amewi Drone Trix 25307

Lees hieronder de 📖 handleiding in het Nederlandse voor Amewi Trix 25307 (1 pagina's) in de categorie Drone. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

2 3 4 51

6 7 8 9 10 11 12

Usage of DIY Stickers: Tear apart the film. Apply the patterned side to the

desired position and use wet tissues or a piece of damp cloth to gently tap the

sticker. 5 to 10 seconds later, peel up one corner of the sticker to see if the

pattern has been printed. If so, rip the whole piece of the sticker.

ACCESSORIES

DRONE applies 2.4G remote control system to allow for multiple players

compete without interference and functions such as forward and backward,

left and right, left sideward and right sideward, left rotation and right rotation,

and 360 degree flips and rolls etc.

Protective Guard

Upper Casing

Lower Casing

Propeller

Motor

Bottom Base

KNOW YOUR

DRONE

1.Propeller Installation

A corresponds to A

B corresponds to B

Front

②Depress the propellers

until fixed.

①Align the propellers to

the motor shaft with the

propellers and the shaft

aligned correctly.

Notes:

When installing or dismantling the propeller, please do not force on the

propeller to avoid distortion.

2.Propeller Replacement

Please replace with new propellers once the

propellers are damaged due to crashes or

collisions. Each propeller is marked with A or B.

When installing, make sure that A corresponds

to A and B to B, otherwise the drone cannot

perform functions such as takeoff, rotation or

throw-to-fly.

ACCESSORY ASSEMBLY

3.Prop Guard Installation

When installing or dismantling the propeller, please do not force on the

propeller to avoid distortion.

Propellers vary from one to another！

Notes:

①Use scissors to pry the

propellers that needs to

be replaced.

②Install the propellers in

order of A to A and B to

B. Hold the propellers,

align to the crankshaft

and depress until fixed.

B A

①Align the protective

guard to the three holes.

②Depress the protective

guard until fixed.

A.Remove the battery from

the bottom of the drone.

B.Connect USB charger with

the battery. (Do not charge

the battery until the water

stains on it have been

vaporized.)

4.Battery Charging for Drone

Notes：

The LED light turns on during charging and turns off when the charging

completes. It takes about 65 minutes to fully charge and gives about 5-6

minutes of running time when fully charged.

!BATTERY INSTRUCTIONS

There is a certain risk when using battery. It may cause fire, body injury or

property loss. Users must be aware of the risks and take full responsibility of

using battery improperly.

If battery leakage occurs, please avoid contacting your eyes or skin with

electrolyte. Once it happens, please wash your eyes with clean water and

seek medical care immediately.

Please remove the plug immediately if you sense any peculiar smell, noise

or smog.

Battery Charging

Please use the original charger to ensure safe use.

Do not charge dilatant or outworn battery.

Do not over charge battery. Please unplug the charger once fully charged.

Do not charge the battery next to inflammables, such as carpet, timber floor

or wood furniture or on the surface of electro-conductive objects. Please

always keep an eye on the battery when charging.

Do not charge battery which not cool down yet.

The charging temperature should be between 0 to 40 .℃ ℃

Battery Recycling

Do not dispose the battery as daily rubbish. Please familiarize yourself with

the local garbage disposal method and dispose it according to the special

requirement.

The flight mode will be turned on by default at startup. The light turns red on

flight mode, turns green when you switch it to ground mode and turns blue

when you switch it to water mode.

Notes:

Speed Mode

Indicator Light

Throttle Joystick

Flight Mode/Ground

Mode/Water Mode

Short Press for Headless

Mode/Long Press for

Return to Home

Flips and Rolls (This

Button Works as

One-key Rotation

on Ground Mode)

Forward/Backward

Fine-tuning

Rudder Joystick

Left/Right Sideward

Fine-tuning

Power Switch

1.Protective Guard the Parts Name of the Remote Control

KNOW YOUR REMOTE CONTROL

②Assemble the Battery

Open the battery compartment cover, insert two AA batteries (not included) with

the two poles aligned correctly.

1.5V AA“ ”

Open the battery compartment cover with a philips screwdriver.

2.Remote Control Battery Installation

①Open the Remote Control Battery Cover

Notes：

1. Ensure the polarity symbols on the batteries match the symbols inside the

battery compartment.

2. Do not mix new and old batteries.

3. Do not mix different types of batteries.

PRE-FLIGHT PREPARATION

1.Flight Environment

Please keep the drone in sight during the flight and keep it away from barriers,

high-tension cables, trees and crowds.

Do not fly in extreme environment, such as hotness, coldness, strong wind or

heavy rain.

Indoor: Spacious spaces away from barriers, crowds or pets are preferred.

Outdoor: Sunny, windless and breezy weathers are preferred.

3.Pairing Remote Control with Drone

①Turn on the power of the drone; put the drone on

plain ground; check whether the indicator lights of

remote control and LED lights of drone flash.

②Push the throttle joystick to the top and then pull

back to the bottom. After the sounds of beep, the

flash of indicator lights of remote control and LED

lights of drone will turn to constant lights, which

means the pairing completes.

Please Check the Followings Before Flying:

①If the drone and the remote controller are fully charged.

②If the propellers have been correctly installed and in good condition.

③If the propellers work well after startup.

④If the surrounding conditions are ideal for a safe flight.

2.Pre-flight Inspection Left Joystick

4.Calibration

If the drone fails to ascend vertically, please

proceed to the calibration process. Toggle the

throttle joystick and the rudder stick towards

toe-out at the same time. When the drone’s

indicator light turns from quick blinking to solid

light, the process of calibration completes.

Please calibrate the drone on a level surface

as to ensure the calibration can be successful.

FLY WITH REMOTE CONTROL

1.Flying

The left joystick is used to control flying height and left and right turning, while

the right joystick is used to control forward, backward and sideward flights.

Right Joystick

Ascend

Descend

Turn Left

Turn Right

Forward

Backward

Left

Sideward

Right

Sideward

①Forward Fine-tuning

②Backward Fine-tuning

③Left Sideward Fine-tuning

④Right Sideward Fine-tuning

①

③

②

④

2.Fine-tuning

Gradually push the throttle joystick to make

the drone ascend. Fine-tune the direction

when the drone rolls or yaws.

If you want to control the speed of the

drone, press the Speed Mode button “ ”

to control it to fly at the speed of 30%,

60% and 100% out of the full speed.

3.Speed Mode

Speed

Mode

Put the drone with its front being your

front. Pair the drone with the remote

controller before its takeoff. Then short

press the Headless Mode button to “ ”

let it enter the headless mode. To exit,

press the Headless Mode button again.“ ”

4.Headless Mode

Headless Mode

Long press the One-key Return button to return the drone automatically. After “ ”

the drone has returned to home point, toggle the front joystick or press the

“ ”One-key Return button to exit the auto return mode. The drone’s light will then

turn solid.

5.One-key Return

Home Point

Finishing Point

One-key Return

Front Flips

and Rolls

Back Flips

and Rolls

Right Joystick

6.Flips and Rolls

Till the drone ascends to the altitude of 3 meters, press the button of flips and

rolls and move the right joystick to certain direction to finalize flips and rolls.

7.Ground Mode/Water Mode

Rotate the accessory part (close to the projections on the tail) on the drone’s

back as shown in figure , and install the drone onto the bottom base as ①

shown in figure . It has been completely set up and ready for takeoff or ②

cruising as shown in figure . (Please wipe off the drone with a piece of dry ③

cloth after water mode.)

② ③①

Doll

Place a doll (not included)

on the brick.

8.Separation of the Drone and the Bottom Base

Put your hands at the tail of the drone and push it forward to

take it apart from the bottom base.

FAQ

PROBLEMS CAUSES SOLUTIONS

Control

failure

Not connect with the drone battery.

Too strong wind force.

Connect the drone battery in

right way.

Fail to

ascend

The wind can affect the drone’s

flight. Therefore, do not fly it in

strong wind conditions.

The rotation speed of main blades

is too slow.

The battery of the drone is not fully

charged.

Push up the throttle joystick.

Please fully charge the battery.

Landing

too soon

The throttle joystick is pulled down

too fast.

Pull down the throttle joystick

slowly to perform a smooth

landing.

Out of

control Beyond the effective controlling

distance.

Ensure that the flying distance

is within 20 meters.

Motor

cannot

rotate

Dust or other objects has been

gathered on the motor.

Clean the dust or remove

other objects on or around

the motor.

Bottom Base x1 Propeller x4

DRONE

(Battery Included)

Remote Control x1

USB Charger x1 User Manual x1Phillips

Screwdriver x1

AGE 14+

VIHICLE X DRONE X HOVERCRAFT 3 IN 1

DRONE

*Please read this manual carefully before operation and keep it properly for

future reference.

3IN1 RC MODEL

Item No.: 25307 / 25308

INSTRUCTION MANUAL

Amewi Trade e.K.

Nikolaus-Otto-Str. 18

D-33178 Borchen

MAXIMUM TRANSMITTING POWER

Operation frequency: 2.405 ~ 2.476 MHz

Maximum Radio frequency power: maximum peak power: 2 dBm

Product specificaties

Merk:	Amewi
Categorie:	Drone
Model:	Trix 25307
Kleur van het product:	Black, Blue
Gewicht:	43 g
Breedte:	145 mm
Diepte:	125 mm
Hoogte:	55 mm
Soort:	Hybride quadcopter
Gebruikershandleiding:	Ja
Capaciteit van de accu/batterij:	350 mAh
Frequentieband:	2.4 GHz
Meegeleverde kabels:	USB
Accu/Batterij voltage:	3.7 V
Levensduur van de batterij:	6 min
Aantal per verpakking:	1 stuk(s)
Aanbevolen gebruik:	Buiten
Aanbevolen geslacht:	Jongen
Accessoires (meegeleverd in doos)::afstandsbediening batterij:::	2 x AA
Batterijen inbegrepen:	Nee
Batterijtechnologie:	Lithium-Polymeer (LiPo)
Type motor:	Elektromotor
Lichteffecten:	Ja
Aantal afstandsbedieningen:	1 stuk(s)