Altronix ACM4CBE Handleiding

Altronix Stekkerdoos ACM4CBE

Lees hieronder de 📖 handleiding in het Nederlandse voor Altronix ACM4CBE (8 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Rev. 082808

ACM4 Series

Access Power Controllers

Installation Guide

Models Include:

ACM4

- Four (4) Fuse Protected Outputs

ACM4E

- Four (4) Fuse Protected Outputs w/Enclosure

ACM4CB

- Four (4) PTC Protected Outputs

ACM4CBE

- Four (4) PTC Protected Outputs w/Enclosure

More than just power.TM

- 2 - ACM4 series

Overview:

These units convert one (1) 12 to 24 volt AC or DC input into four (4) independently controlled fused or PTC protected

outputs. These power outputs can be converted to dry form “C” contacts (ACM4/ACM4E only). Outputs are activated by

an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push

Button, PIR, etc. The units will route power to a variety of access control hardware devices including Mag Locks, Electric

Strikes, Magnetic Door Holders, etc. All interconnecting devices must be UL Listed. Outputs will operate in both Fail-Safe

and/or Fail-Secure modes. Units are designed to be powered by one common power source which will provide power for

both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for

board operation and the other for lock/accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring,

or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all

of the four (4) outputs.

Configuration Reference Chart:

*Install in Altronix Power Supply/Chargers AL300ULX, AL400ULX and AL600ULX only. Total output current when

ACM4/ACM4CB is utilized as a sub-assembly with power supply/chargers listed below (see Total Output Chart, below).

Note: The total for all outputs combined is not to exceed 8 amp for ACM4CBE and 10 amp for ACM4E.

Total Output Chart:

Note: ACM4/ACM4CB can only be utilized with the power supplies listed above.

Specifications:

• olt 12 to 24v AC or DC operation (setting not required).

• Input Ratings (ACM4/ACM4CB only):

- 12VDC @ .4 amp or 24VDC @ .2 amp.

Input Ratings (ACM4E/ACM4CBE only):

- 12VDC @ .4 amp or 24VDC @ .2 amp.

- 12VAC @ .4 amp or 24VAC @ .3 amp.

• Power supply input options:

a) One (1) common power input (board and lock power).

b) Two (2) isolated power inputs (one (1) for board power and one (1) for lock/hardware power).

• Four (4) Access Control System trigger inputs:

a) Four (4) normally open (NO) inputs.

b) Four (4) open collector sink inputs.

c) Any combination of the above.

• Four (4) independently controlled outputs:

a) Four (4) Fail-Safe and/or Fail-Secure power outputs.

b) Four (4) dry form “C” 5 amp rated relay outputs (ACM4/ACM4E only).

c) Any combination of the above (ACM4/ACM4E only).

• Four (4) auxiliary power outputs (unswitched).

Altronix

Model

Number

ACM4 4 x ---- 3 amp - * UL File # BP6714

UL Listed for Access Control

System Units (UL 294).

“Signal Equipment” Evaluated to

CSA Standard C22.2

No.205-M1983

ACM4E 4 x ---- 3 amp - x

ACM4CB 4 x---- 2 amp x *

ACM4CBE 4 x---- 2 amp x x

Number of

Outputs

Fuse Protected

Outputs

PTC Protected

Outputs

Output Ratings

(per output)

Enclosure

Agency Listings

UL Listings and

File Numbers

Class 2 Rated Power

Limited Outputs

UL Listed

Sub-Assembly.

UL Listed

Accessory.

UL Listed

Sub-Assembly.

UL Listed

Accessory.

Power Supply 12 volt DC Output 24 volt DC Output

AL300ULX 2.1 amp 2.3 amp

AL400ULX 2.8 amp 3.6 amp

AL600ULX 5.6 amp 5.8 amp

ACM4 series - 3 -

• Output ratings:

- Fuses are rated 3 amp each.

- PTCs are rated 2.5 amp each.

• Main fuse is rated at 10 amp.

Note: The total for all outputs combined is not to exceed 8 amp for ACM4CBE and 10 amp for ACM4E.

(For Models ACM4/ACM4CB refer to the Total Output Chart on Page 2).

Note: Operating temperature range should be 0 to +49

oC.

• Red LEDs indicate outputs are triggered (relays energized).

• Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the four (4) outputs.

Fire Alarm disconnect input options:

a) Normally open (NO) or normally closed (NC) dry contact input.

b) Polarity reversal input from FACP signaling circuit.

• FACP output relay (form “C” contact rated @ 1 amp 28VDC not evaluated by UL).

• Green LED indicates when FACP disconnect is triggered.

• Removable terminal blocks facilitate ease of installation.

Board Dimensions (approximate): 5.125”L x 3.625”W x 1.25”H (ACM4 and ACM4CB).

Enclosure Dimensions (approximate): 8.5”H x 7.5”W x 3.5”D (ACM4E and ACM4CBE).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and

authorities having jurisdiction. Product is intended for indoor use only.

1. For ACM4/ACM4CB sub-assembly boards, use stand-offs to mount only in AL300ULX, AL400ULX or

AL600ULX enclosures (Figs. 8-9, pg. 8). For ACM4E/ACM4CBE units, mount in desired location.

The enclosure door for the ACM4E/ACM4CBE can be fastened by using either a cam lock or screws (both supplied).

Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install three upper

fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two

upper screws, level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower

holes and install the two fasteners. Place the enclosure’s upper keyholes over the two upper screws. Install the

two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 7).

Carefully review:

Typical Application Diagram (pg. 4) Terminal Identification Table (pg. 5)

LED Dia Hook-up Diagnostics (pg. 5) grams (pg. 6)

2. Power supply input:

The units can be powered with one (1) Listed Access Control Power Supply which will provide power for both

board operation and the locking devices or two (2) separate Listed Access Control Power Supplies, one (1) to provide

power for the board operation and the other to provide power for the locking devices and/or access control hardware.

Note: The input power can be either 12 to 24 volts AC or DC operation.

Input Ratings (ACM4/ACM4CB only):

- 12VDC @ .4 amp or 24VDC @ .2 amp.

Input Ratings (ACM4E/ACM4CBE only):

- 12VDC @ .4 amp or 24VDC @ .2 amp.

- 12VAC @ .4 amp or 24VAC @ .3 amp.

(a) Single power supply input:

If the unit and the locking devices are to be powered using a single Listed Access Control Power Supply, connect

the output (12 to 24 volts AC or DC) to the terminals marked [- Control +].

(b) Dual power supply inputs (Fig. 1, pg. 4):

When the use of two Listed Access Control Power Supplies is desired, jumpers J1 and J2 (located to the left

of the power/control terminals) must be cut. Connect power for the unit to the terminals marked [- Control +]

and connect power for the locking devices to the terminals marked [- Power +].

Note: When using DC Listed Access Control Power Supplies polarity must be observed. When using AC Listed

Access Control P

ower Supplies polarity need not be observed.

Note: For UL compliance the power supplies must be UL Listed for Access Control Systems and accessories.

3. Output options (Fig. 1, pg. 4):

The ACM4/ACM4E will provide either four (4) switched power outputs, four (4) dry form “C” outputs, or

any combination of of both switched power and form “C” outputs, plus four (4) unswitched auxiliary power outputs.

The ACM4CB/ACM4CBE will provide four (4) switched power outputs or four (4) unswitched auxiliary power outputs.

(a) Switched Power outputs:

Connect the negative (-) input of the device being powered to the terminal marked [COM]. For Fail-Safe operation

Product specificaties

Merk:	Altronix
Categorie:	Stekkerdoos
Model:	ACM4CBE
Kleur van het product:	Grijs
Gewicht:	2990 g
Certificering:	UL294, CUL C22.2 No.205-M1983, RoHS
Spanning:	12 V
Afmetingen (B x D x H):	191 x 89 x 216 mm
Aantal AC uitgangen:	4 AC-uitgang(en)