Alcatel Versatis E100 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Alcatel Versatis E100 (3 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/3
Unpacking your phone
In the box you will find:
• the cordless handset (two handsets with a Twin system, and three with a
Triple system)
• the base unit
• two rechargeable battery cells for each handset
• a battery compartment cover for each handset
• a telephone line cable for the base unit
• a mains power lead and adapter for the base unit
• charger pods, each with an attached mains power lead and adapter, for
multihandset system
Before you start to use your telephone make sure that all batteries are fully
charged for 15 hours.
Important note: This telephone is not designed for Emergency calls when the
mains power fails
For Emergency calls you should have a basic phone that operates without
mains power, connected to your line so that you can make calls during a
power failure.
USER'S GUIDE
1. Press in idle mode to browse the phonebook entries. Alternatively, you
can press MENU key, to display and then press OK.PHONEBOOK
2. Press NAVIGATION key to select and then press OK key to confirm.LIST
The phonebook entries will be listed in alphabetical order, and you can press
NAVIGATION key to scroll through the stored entries.
3. Press OK key to view the details of the selected entry.
Note : Instead of pressing NAVIGATION key to browse the phonebook entries,
you can press the numeric key corresponding to the first letter of the entry you
wish to locate.
Modify a phonebook entry
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PHONEBOOK and then press OK key
to select.
3. Press NAVIGATION key to select EDIT ENTRY and then press OK key
to select.
4. Press NAVIGATION key to select an entry to edit and then press OK key.
The current name is displayed.
Edit the name and then press OK key to confirm.
5. Edit the number and then press OK key to confirm. A confirmation beep is
played.
Delete a phonebook entry
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PHONEBOOK and then press OK key
to select.
3. Press NAVIGATION key to select and then press OK key to select.DELETE
4. Press NAVIGATION key to select an entry to delete and then press OK key.
5. Press OK key again to confirm. A confirmation beep is played.
Delete all entries from the phonebook list
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PHONEBOOK and then press OK key
to select.
3. Press NAVIGATION key to select DELETE ALL and then press OK key
to select.
4. Press OK key again to confirm. A confirmation beep is played.
Direct access memory
There are 2 direct access memories (Keys 1 & 2) in addition to the phonebook
memory. A long press on the keys in idle mode will automatically dial the
stored phone number.
Add/edit direct access memory
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PHONEBOOK and then press OK key to
select.
3. Press NAVIGATION key to select . and then press OK key to DIRECT MEM
select.
4. Press NAVIGATION key to select KEY 1 KEY 2 or and then press OK key.
The stored name is displayed, or NO NUMBER if it is empty.
If there is no number stored for the selected key or if you want to change the
name or number currently stored, press MENU key to enter direct memory
menu to add/edit the name or number.
5. Press NAVIGATION key to select EDIT NUMBER and then press OK key
to select. The display shows the currently stored name, or ENTER NAME if
there is no number stored. Edit or enter the name you want and then press
OK key. The display shows the currently stored number, or ENTER NUMBER
if there is no number stored. Edit or enter the number you want and then press
OK key to confirm. A confirmation beep is played.
Delete direct access memory
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key PHONEBOOK
to select.
3. Press NAVIGATION . and then press OK key key to select DIRECT MEM
to select.
4. Press NAVIGATION key to select or KEY 1 KEY 2 and then press OK key.
The stored name is displayed (or NO NUMBER if it is already empty).
5. Press MENU key to enter direct memory menu.
6. Press NAVIGATION select. key to select and then press OK key toDELETE
Press OK key again to confirm. A confirmation beep is played.
Using the redial list
The redial list stores the last 5 numbers dialed.
Access redial list
1. Press REDIAL key in idle mode and press NAVIGATION key to browse the
redial list. The last number dialed will appear first in the redial list.
2. Press OK key to view the details of the selected entry.
Save a redial number into the phonebook
1. Press REDIAL key in idle mode to go to the redial list.
2. Press NAVIGATION key to select an entry.
3. Press MENU key to display SAVE NUMBER, then press OK key to display
ENTER NAME. Enter the name of the contact (maximum 12 characters) and
then press OK key to save the entry, and return the display to the redial list.
Phone Function Keys 1 OK key
Press to select the function displayed on the
handset screen directly above it.
2 Back/clear key
Press to delete a digit/a character in editing mode
Press to return to idle mode.
Press and hold to change the handset idle display
between handset name and date/time.
3 Navigation key
Press UP to access the call log* and press DOWN
to access the phonebook when in idle mode.
Press UP/DOWN to increase or decrease
earpiece volume during a call.
Press to increase or decrease the ringer volume.
Press UP/DOWN to increase or decrease
handsfree volume (Versatis E150 only)
Scroll up/down a list.
4 Talk key
Press to accept or make a call
Press to activate handsfree mode (Versatis E150
only)
5 Hang-up/Exit key
Press and hold to switch the handset power
on/off.
Press to end a call.
Press to return to idle mode in other menus.
6 Recall (Flash) key
Access to operator services*
7 Menu key
Press to access the main menu.
8 Redial key
Press to access the Redial list.
9 Star key
Press and hold to lock/unlock keypad.
Press and hold to toggle between the external and internal calls when both are set up.
10 Hash key
Press and hold to insert a pause during a call.
Press and hold to turn the ringer on/off.
11 Mute key
Press to mute / unmute the handset microphone.
12 Call transfer/Intercom key
Press to initiate an internal call.
Press to hold the line and page another handset during a call.
Press and hold to initiate a conference call.
*Subject to subscritption and availability of the service from the fixed line operator.
What the icons mean?
Indicates battery is fully charged.
Indicates battery is fully discharged.
Indicates that an external call is connected or held.
Icon blinks when receiving an incoming call.
Indicates you have a new Voice Mail message*.
Indicates you have new missed calls*, or the call log is being viewed.
Displays when the phonebook is accessed.
Displays when the alarm clock is activated.
Displays when handsfree is activated (Versatis E150 only).
Displays when ringer volume is turned off.
Indicates that the handset is registered and within range of the base station.
Icon blinks when the handset is out of range or is searching for a base.
Displays when in menu mode to confirm your selection.
Indicates that more options are available.
Use the UP / DOWN keys to scroll up/down.
Displays when in menu mode.
Select BACK to return to the previous menu level.
ATLINKS Europe, 22 quai Gallieni 92150 Suresnes – France
Alcatel Logo and Alcatel name are trademarks of Alcatel and used under license by Atlinks.
Installation and Set-up
Precautions
The signal quality will depend on the location and environment of the base and
handset. Position your Versatis E100 / Versatis E150 away from sources of
excessive heat (radiators, direct sunlight, etc.) and protect it from vibrations and
dust. Never allow your telephone to come into contact with water or other liquids,
or with aerosols. To reduce the risk of interference and optimize reception, take
particular care not to install the base in the immediate vicinity of windows, large
metal objects, reinforced concrete, televisions, music centres, VCR or DVD
players, halogen lamps or heating devices, fluorescent lighting, burglar alarms,
microwave ovens, computers, etc.
This telephone requires an electrical power supply in order to function.
To clean your Versatis E100 / Versatis E150, use an antistatic cloth lightly
moistened with water.
NB: Your Versatis E100 / Versatus E150 is a DECT™* standard appliance
designed to receive and transmit telephone calls. It is designed for
connection to the public telecommunications network.
Fit the rechargeable batteries in each handset
1) Install the AAA batteries (Brand name: CORUN, Capacity: Ni-MH 1.2V/
400mAh, or Brand name: SANIK, Capacity: Ni-MH 1.2V/400mAh) into handset
in accordance with the polarity marked in the battery compartment.
2) Close the battery compartment cover, sliding it into place and pressing firmly
to make sure it is secure.
Connecting AC (electrical) power
1. Plug the base adaptor cord into the power jack on rear panel of the base
and the other end into a 100-240 Vac 50-60Hz electrical outlet.
2. Connect telephone line cord into the phone jack on rear panel of the base
and the other end into a main socket.
3. In case of twin or triple system, plug the charger power adaptor cord into
the power jack on rear panel of charger and the other end into a 100-240
Vac 50-60Hz electrical outlet.
Before you use the cordless handset for the first time, it’s important to
charge the batteries fully.
Leave the handset on the charging cradle for 15 hours.
CAUTION: Use only the power supply that came with this unit. Using other
power supplies may damage the unit.
Base and charger power adaptor :
S003IV060050 100-240V 16V 500mA ou IA5060 100-240V 16V 500mA
S003IV060015 100-240V 16V 150mA ou IA5060 100-240V 16V 500mA
Your Telephone Operations
Switching on/off
Press and hold the HANG-UP/EXIT key for more than 2 seconds to
switch on/off the handset in idle mode.
Notes: When the handset is OFF, it cannot be used for making calls including
emergency calls. There will be no ringing during an incoming call. To answer
a call, you will need to switch it back on. It may take some time for the handset
to re-establish a radio link with the base unit.
To lock/unlock the keypad
Press and hold the STAR key for 1 second to lock/unlock the keypad
in idle mode.
Note: Incoming calls can still be answered even if the keypad was locked.
Battery safety - CAUTION
ONLY use the rechargeable batteries supplied with the handset.
DO NOT use non-rechargeable batteries - they may explode and cause
damage to your telephone.
Read First Before Use
Choosing a site for the base unit and charger pod
If you have a Broadband line
If you connect your telephone to a line with a broadband connection, you
will need to insert a microfilter between the telephone and the telephone
line, otherwise you may get interference between the telephone and the
broadband, which could cause problems.
Mute/unmute microphone
When the microphone is muted, the handset displays MUTE ON, and your caller
cannot hear you.
During a call, press the MUTE key to turn on/off the microphone.
Paging
The paging feature enables you to locate a missing handset if the handset is
in range and contains charged batteries.
Press HANDSET LOCATOR key located at the back of the base
station. All the registered handsets start to ring.
Once retrieved, press any key on the handset or the HANDSET
LOCATOR key again to end the paging.
Call waiting
If you have subscribed to Call Waiting service, the earpiece will emit a beep
tone to inform you that there is a second incoming call. The number or name
of the second caller will also be displayed on your phone if you have
subscribed to Caller Line Identification service (CLI). Please contact your
network provider for more information on this service.
Using your phonebook
Your phone can store up to 50 phonebook memories.
How to enter characters?
When you select a field in which you can enter text, you can enter the letters
that are printed on the keys by pressing the relevant key once or several times.
For example, press once to insert the letter ‘A’, press twice to insert
the letter B, and so on... Spaces and other symbols can be entered using
or .
Store a contact in the phonebook
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PHONEBOOK and then press OK key
to select.
3. Press OK key again to enter NEW ENTRY.
4. Enter the name of the contact (maximum 12 characters).
To edit, press BACK/CLEAR key to delete the last character entered.
Press OK key to confirm the name entry.
5. Enter the number of the contact (maximum 24 digits) and then press OK
key to confirm. A confirmation beep is played.
Set time and date
Note: If you subscribe to the Caller Display service, the time and date will be
set automatically when you receive a call, but you may still need to set the
correct year.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select CLOCK&ALARM and then press OK key
to select.
3. Press OK key to select DATE/TIME. The last stored date is displayed.
Enter the current date (YY-MM-DD), press OK, then enter the time (HH-MM).
Change your handset’s name
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PERSONAL SET and then press OK
key to select.
3. Press NAVIGATION key to select HANDSET NAME and then press OK
key to select. The current handset name is displayed.
4. Press BACK/CLEAR key to delete the characters one by one.
Enter the new name (maximum 10 characters) and press OK key to confirm.
A confirmation beep is played.
Change the display language
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select PERSONAL SET and then press OK
key to select.
3. Press NAVIGATION key to select LANGUAGE and then press OK key
to select.
4. Press NAVIGATION key to your desired language and press OK key to
confirm. A confirmation beep is played.
Note : Once the display language is set, the option menus on the handset will
switch to display in the selected language immediately.
Make and answer calls
Make a callPredialling
Dial the number (maximum 24 digits) and then press TALK key.
Direct dialling
Press TALK key to take the line and then dial the number
(maximum 24 digits).
Call from redial list
Press REDIAL key in idle mode.
Press NAVIGATION key to select an entry in the redial list and then
press TALK key.
Call from the call log
Press in idle mode.
Press NAVIGATION key to select an entry in the call list and then
press TALK key.
Note: You need to subscribe to Caller Line Identification service to be able
to see the caller’s number or name in the call log.
Call from the phonebook
Press in idle mode.
Press NAVIGATION key to select an entry in the phonebook and then
press TALK key.
Answer and end a call
1. When the phone rings, press TALK key. You can also use handsfree mode
thanks to a long press on TALK key (only on Versatis E150)
2. To end a conversation, press HANG-UP/EXIT key.
IMPORTANT NOTE: You can simply place the handset back on its base
station or charger pod to end the call.
Use handsfree (only for Versatis E150)
Press and hold the TALK key at any moment to talk in handsfree mode.
To deactivate the handsfree mode, press again the TALK key.
Adjust the earpiece volume
During a call, press NAVIGATION key to select from VOLUME 1 to VOLUME 3.
Only use rechargeable batteries with exactly the same specifications as
those supplied with the product.
Using non-rechargeable or non-conforming batteries can damage the
product and could pose a health hazard (see Chapter 9 “Technical
Specifications”).
Failure to comply with this recommendation will invalidate the manufacturer's
warranty.
Batteries can split or leak if incorrectly inserted, opened or exposed to heat.
Never dispose of batteries in a fire: they could explode.
Access phonebook
/
/
/
/
Base station
D
C
What’s on the display?
A
B
A Display Icons
B Displays when in menu mode to confirm
your selection.
C Indicates that more options are available.
Use the UP / DOWN keys to scroll up/down.
D Displays when in menu mode.
Select BACK to return to the previous menu
level. Select BACK to delete the last digit/
character entered.
HANDSET LOCATOR button
Press to page handsets.
Press and hold to start registration procedure.
4. Press NAVIGATION and then press OK to select. key to select KEY BEEP
5. Press NAVIGATION key to select or and then press OK key to ON OFF
confirm. A confirmation beep is played.
Activate/deactivate auto hang-up
This function enables you to end a call automatically by simply placing the
handset on the base station. By default, the Auto Hang up feature is ON.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK PERSONAL SET
key to select.
3. Press NAVIGATION key to select and then press OK AUTO HANG-UP
key to select.
4. Press NAVIGATION key to select or and then press OK key to ON OFF
confirm. A confirmation beep is played.
Set date/time format
You can set your preferred date/time format for your phone. The default
format is DD/MM and 24 HOURS.
Set time format
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK CLOCK&ALARM
key to select.
3. Press NAVIGATION key to select SET FORMAT and then press OK key
to select.
4. Press OK key to enter TIME FORMAT. The current setting is displayed.
5. Press NAVIGATION key to select or and then 12 HOURS 24 HOURS
press OK key to confirm. A confirmation beep is played.
Set date format
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key CLOCK&ALARM
to select.
3. Press NAVIGATION key to select SET FORMAT and then press OK key to
select.
4. Press NAVIGATION key to select DATE FORMAT and then press OK key
to select. The current setting is displayed.
5. Press NAVIGATION key to select or and then press OK DD/MM MM/DD
key to confirm. A confirmation beep is played.
Set alarm
The handset has an alarm clock feature, and when the alarm is set, the is
shown on the handset display.
When the alarm time is reached, the display flashes -- -- and the alarm ALARM
melody is played for 1 minute or until any handset key is pressed.
If the alarm is set for ON DAILY and the alarm will sound again on the next day.
If the alarm was set for ON ONCE, the will be turned off.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key CLOCK&ALARM
to select.
3. Press NAVIGATION and then press OK key to select. key to select ALARM
4. Press NAVIGATION key to select , or OFF ON ONCE ON DAILY and then
press OK key to confirm.
If you select or ON ONCE ON DAILY, enter the time (HH-MM) for the alarm
and press the UP/DOWN key to select AM or PM if the time is in 12 HOURS
format.
5. Press OK key to confirm. A confirmation beep is played.
Set alarm tone
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key CLOCK&ALARM
to select.
3. Press NAVIGATION key to select and then press OK key ALARM TONE
to select.
4. Press NAVIGATION key to select , MELODY 1 MELODY 2 MELODY 3 or
and then press OK key to confirm. A confirmation beep is played.
Advanced use of your telephone
Change Master PIN
The Master PIN is used for registration/unregistration of handsets. The default
Master PIN number is 0000. The maximum length of the Master PIN is 8 digits.
Note: If you forget your PIN code, you can reset it to its default 0000 using a
handset Reset (see section Reset Unit).
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select ADVANCED SET and then press OK key
to select.
3. Press NAVIGATION key to select and then press OK key to CHANGE PIN
select.
Enter the current Master PIN when prompted and then press OK key to confirm.
As you enter the PIN it will be shown as asterisks (*) on the screen.
(Enter the new PIN and then press OK key to confirm. A confirmation beep is
played.)
Register your handset
IMPORTANT: When you purchase a telephone, all handsets are already
registered to the base, so you do not need to register them. Handset
registration is only necessary when you buy extra handsets or if a handset
has become faulty.
The procedure described below is for Versatis E100 or Versatis E150. They
may be different if you want to register another handset model, in which case
you should refer to its user guide.
Additional handsets must be registered to the base unit before you can
use them. Up to 4 handsets can be registered to one base station.
The Master PIN is required before you can register or unregister handsets.
By default, the Master PIN is 0000.
On the base station, press and hold the HANDSET LOCATOR key for
approximately 5 seconds.
1. On the handset, press MENU key to enter menu selection.
2. Press NAVIGATION key to select ADVANCED SET and then press OK
key to select.
3. Press NAVIGATION key to select REGISTRATION and then press OK
key to select.
Note : If no action is taken on the handset within 10 seconds, the
registration procedure will be aborted. If this happens, repeat the first step.
WAITING is displayed on the screen. A confirmation beep is played to
indicate successful registration, and the handset will return to idle mode,
with its handset number displayed.
Note : If no base is found within a certain period, NO BASE will be
displayed with an error tone to indicate failed registration and the handset
returns to idle mode, and you will need to repeat the registration sequence.
Unregister your handset
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select ADVANCED SET and then press OK
key to select.
3. Press NAVIGATION key to select and then press OK key UNREGISTER
to select.
4. Enter the Master PIN when prompted and then press OK key to confirm.
(the default master PIN is 0000)
5. Press NAVIGATION key to select the handset number to unregister and
then press OK key to confirm.
A confirmation beep is played to indicate successful unregistration.
Note : If no action is taken on the handset within 15 seconds, the
unregistration procedure will be aborted and the handset returns to idle
mode.
You must use another handset to unregister handsets from the base.
Change recall time
You may need the R button to send a Recall signal (also called Flash or
Timed Break Recall) if you are connected to a PBX. You should normally
leave the Recall Time at its default setting of Short (100ms), as this is the
standard recall required in the telephone network, but it can be changed to
Medium (270ms) or Long (600ms) if your telephone is connected to a PBX
that requires a different recall time.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select ADVANCED SET and then press OK
key to select.
CONFORMITY
This unit conforms to the following rules and regulations: 1995/5/EC Radio frequency and
telecommunication equipment and the mutual acceptance of conformity.
The CE mark proves the above.
ENVIRONMENT
This symbol means that your inoperative electronic appliance must be collected
separately and not mixed with the household waste.The European Union has
implemented a specific collection and recycling system for which producers are
responsible.
This appliance has been designed and manufactured with high quality materials and
components that can be recycled and reused. Electrical and electronic appliances are liable
to contain parts that are necessary in order for the system to work properly but which can
become a health and environmental hazard if they are not handled or disposed of in the
proper way. Consequently, please do not throw out your inoperative appliance with the
household waste.
If you are the owner of the appliance, you must deposit it at the appropriate local collection
point or leave it with the vendor when buying a new appliance.
- If you are a professional user, please follow your supplier's instructions.
- If the appliance is rented to you or left in your care, please contact your service provider.
Keen to preserve the environment, ATLINKS has equipped this appliance with a switching
power supply, offering better energy efficiency. The advantages include not only very low
electricity consumption, but also a more compact format than the conventional power
supply units used by the previous range.
The used batteries from your telephone (if it has batteries) must be disposed of in
compliance with current environmental protection regulations. Comply with your local
regulations.
Return your batteries to your reseller or dispose of them at an approved recycling centre.
Help us protect the environment in which we live!
Model E100 / E100 Duo / Trio
E150 / E150 Duo / Trio CG1
A/W No. : 10000330 Rev.0 (EN)
Made in China
Delete a Call Log entry
1. Press in idle mode to go to the call list.
2. Press NAVIGATION key to select an entry and then press MENU key.
3. Press NAVIGATION and then press OK key to select. key to select DELETE
(Press OK key again to confirm. A confirmation beep is played.)
Delete all entries in the Call Log
1. Press in idle mode to go to the call list.
2. Press MENU key.
3. Press NAVIGATION key to select and then press OK key DELETE ALL
to select.
(Press OK key again to confirm. A confirmation beep is played.
Using the intercom
Intercom, call transfer and conference are only possible with at least 2 handset
registered to the same base station. It allows you to make free internal calls,
transfer external calls from one handset to another, and set up a 3-way
conference with two handsets and an external call.
If you try to make a call while another handset is already on an external call,
you'll hear a busy tone for a few seconds before the display returns to idle.
Intercom another handset
Press INT key in idle mode.
Intercom is established immediately if there are only 2 registered
handsets.
If there are more than 2 registered handsets, the handset numbers which
are available for intercom, and a * will be displayed. Press the specific
handset number you wish to call, or press to ring all handsets, to start
intercom.
Transfer an external call to another handset
During the call, press INT key to put the external call on hold
(the caller can no longer hear you).
Intercom is established immediately if there are only 2 registered handsets.
If there are more than 2 registered handsets, the handset numbers which
are available for intercom, and a * will be displayed. Press the specific
handset number you wish to call, or press * to ring all handsets, to start
intercom.
The store where you bought your telephone can also provide you with information and after-sales support.
SAFETY
In the event of an electrical hazard, the mains adapter acts as 230V power isolating device. It should
therefore, as a precaution, be installed close to the appliance and be easily accessible. To disconnect the
device from the primary power source, the mains adapter must be removed from the 230V AC/50 Hz socket.
If the mains adapter fails, it must be replaced by an identical model.
If not connected to the mains power or if there is a mains power failure, telephones that use cordless
handsets will not work.
You will then be unable to make or receive calls in the event of an emergency.
This is why we recommend that you also keep a conventional telephone – one that doesn’t require a power
supply – as a backup.
! Do not use your telephone to notify a gas leak when standing in the vicinity of the leak.
It is recommended that you avoid using this device during electrical storms.
Do not attempt to open the batteries, as they contain chemical substances. In the event of leakage,
avoid contact with the skin, eyes, nose and mouth. In the event of contact, rinse the affected part for about
twenty minutes with running water and seek urgent medical attention. Clean the product with absorbent
paper or a dry cloth and contact your reseller for replacement batteries.
ATLINKS hereby declares that the following models conform to the essential requirements and other
applicable provisions of European directive 1999/5/EC.
Versatis E100 / Versatis E100 Duo / Trio
Versatis E150 / Versatis E150 Duo / Trio
ATLINKS, 22 quai Gallieni 92150 Suresnes – France
S.A.S. (Simplified Joined Stock Company) with capital of 500 000 Euros -
Registration number: 508 823 747 R.C.S. Nanterre.
© ATLINKS 2011 - Reproduction prohibited.
The manufacturer reserves the right to modify the specifications of its products
in order to make technical improvements or comply with new regulations.
ALCATEL, VERSATIS and ATLINKS are registered trademarks.
The Alcatel logo and Alcatel name are trademarks of Alcatel and used under
license by ATLINKS.
If there are more than 2 registered handsets, the handset numbers which are
available for intercom will be displayed. Press the specific handset number
you wish to call to start intercom.
Press TALK key on the called handset to answer the internal call, where
both internal callers can talk. Intercom is established.
Press and hold INT key for 2 seconds on the first handset to start the
three-party conference.
CONFERENCE will be displayed on the screen once the conference
call is established.
Handset Tone
Set the ring volume
There are 5 ringer volume options (OFF, LEVEL 1, LEVEL 2, LEVEL 3 and
LEVEL 4). The default level is LEVEL 2.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK PERSONAL SET
key to select.
3. Press NAVIGATION key to select and then press OK HANDSET TONE
key to select and show RING VOLUME. Press the OK key again to select.
4. Press NAVIGATION key to your desired volume level and then press OK
key to confirm. A confirmation beep is played.
Set the ring melody
There are 10 ring melodies available on your handset.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key PERSONAL SET
to select.
3. Press NAVIGATION key to select and then press OK key HANDSET TONE
to select.
4. Press NAVIGATION key to select and then press OK to RING TONES
select.
5. Press NAVIGATION key to your desired melody and then press OK key to
confirm. A confirmation beep is played.
Activate/deactivate key tone
A single tone is emitted when a key is pressed. You can enable or disable the
key tone. By default, the key tone is ON.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select and then press OK key PERSONAL SET
to select.
3. Press NAVIGATION key to select and then press OK key HANDSET TONE
to select.
Press TALK key on the called handset to answer the internal call, where
both internal callers can talk. Intercom is established.
Press HANG-UP/EXIT key on the first handset to transfer the external
call to the called handset. The external call is transferred.
Note : If there is no answer from the called handset, press INT key to resume
the external call.
Answer an external call during intercom
During intercom, a new call tone is emitted when there is an incoming external
call.
Press TALK key to answer the external call and end the intercom.
Connection with the external call is established.
Note : To put the internal call on hold and answer the incoming external call,
press INT key.
Switch between an internal and external call
During the call, press key to switch between an internal or external
call.
Establish a three-party conference call
The conference call feature allows one external call to be shared with two
handsets (in intercom). The three parties can share the conversation and no
additional network subscription is required.
During an external call, press INT key to put the external call on hold
(the caller can no longer hear you).
Technical details
Using the call log
To receive Caller ID you may need to contact your telephone service provider,
and they will inform you also of any charges for it.Caller ID lets you see the
phone numbers of your callers on the handset display, before answering and
in your Call Log afterwards.The Call Log stores the last 10 external calls,
whether or not you answered the call, so you can call them back later.
Only the most recent call is saved if there are repeat calls from the same
number. When the Call Log is full, the next new call will replace the oldest
entry.
If you've got a new call in the Call Log, will appear on the handset display.
If the received number is the same as one in your phonebook, the name from
the phonebook will display as well as the number.
If a call is from someone who withheld their number, the display will show
WITHHOLD ID.
If the call is from someone whose number is unavailable, or if you have not
subscribed to Caller ID but have set the date and time, the display will show
CALLING UNAVAILABLE when it is received and in the Call Log.
Access call log
Press in idle mode and press NAVIGATION key to browse the call list.
The calls are displayed in chronological order with the most recent call at the
top of the list.
1. Press OK key to display more details of the call, including the date and time.
Save call list entry into the phonebook
2. Press in idle mode to go to the call list.
3. Press NAVIGATION key to select an entry and then press MENU key.
4. Press NAVIGATION key to select SAVE NUMBER and then press OK key
to select (Enter the name of the contact (maximum 12 characters) and then
press OK key to confirm.
3. Press NAVIGATION key to select and then press OK key RECALL TIME
to select.
4. Press NAVIGATION key to select , or and then SHORT MEDIUM LONG
press OK key to confirm. A confirmation beep is played.
Reset unit
You can reset your phone to its default settings with this feature.
Note: Upon reset, all your personal settings, call log and redial list entries will
be deleted and the phone will return to its default settings. However, your
phonebook will remain unchanged after reset.
1. Press MENU key to enter menu selection.
2. Press NAVIGATION key to select ADVANCED SET and then press OK
key to select.
3. Press NAVIGATION and then press OK key to select. key to select RESET
4. Press OK key again to confirm. A confirmation beep is played and the unit is
reset to its default settings.
* Value may to vary according environment.
** Depending charge. on initial battery
Free field to range Up 300 meters*
Indoor to range Up 50 meters*
Handset battery life
(averag values)e
7 hours talktime**
100 hours standby**
Number Up of handsets to 4
Intercom mode Yes
Three -way confere
(1 outside correspondent +
2 internal correspondents)
Yes
Electrical connection /
Base mains adapter /
Charger
Base: S003IV0600050 or IA5060
Charger: S003IV0600015 or IA5060
Input: / 100-240 V 50-60 Hz
Output: 6 / V DC 500 mA(BASE)
6V DC / 150mA (charger) ; (500mA for IA5060)
Only use the adapters supplied with the telephone.
Single-phase AC, excluding IT installations defined by
the st the network t is EN 60950 andard. Caution: vol age
classified as a by the criteria of this sthazard andard.
Telephone connection Appliance designed TNV3 for connection to a class
(telecommunications t network vol age) analogue
telephone line as defined by the stEN 60950 andard.
Batteries / Sanik Corun – AAA – 1.2 V – 400 mAh
Only use the batteries supplied with the telephone.
Using any other type of battery presents a risk of
explosion.
Used batteries must be disposed of in compliance with
current tal protection environmen regulations.
Operating 5 40° C temperature From to
Troubleshooting
If you have difficulty with your phone, please try the suggestions listed below.
As a general rule, if a problem occurs, remove the batteries from all the
handsets in your installation for about 1 minute, then disconnect and reconnect
the power supply to the base and reinstall the handset batteries.
ALWAYS check first that: You have followed all the steps listed in the user
manual to install and set up your telephone.
All connectors are firmly inserted in their sockets.
Mains power to the base unit is switched on at the
socket.
The handset’s batteries are correctly and securely
installed and are not run down.
Everyday use
“I cannot make or answer calls”
“I cannot make a call”
“When I press on the keys,
nothing happens”
“The phone does not ring”
“I hear ‘beeps’ from my
handset while I’m on a call”
“When I try to make a call, I
hear busy tone”
“The volume in the earpiece is
low when I’m on a call”
Batteries
“The handset’s battery cells
are running low within
an hour or two”
“I try to recharge the batteries
but I still get a warning that
they are low”
If the fault persists...
If the handset’s display is blank, it may have been
switched off. Press and hold the HANG-UP/EXIT
key to switch it back on.
Check that the base unit’s mains power adapter is
plugged in and power is switched on.
The base unit needs mains power for normal
operation of the phone
- not just for charging the batteries.
Make sure you are using the telephone line cable
supplied with your telephone. Other telephone line
cables might not work. Move the handset closer to
the base unit.
Check the battery level symbol on the display. If it
is low, replace the handset on the base unit or
charger pod to recharge the batteries.
Switch off power at the mains socket, wait for a
short time and then switch back on. This may
solve the problem.
If the handset display shows KEYS LOCKED,
press and hold the * button to unlock it before you
make a call.
Only one handset (or the base unit) can be
connected to the outside line at a time. If another
handset is already using the line, you need to wait
until it has finished its call.
Make sure the batteries are fitted in your handset
If the Battery Level symbol on the display shows
‘low’, put your handset back on the cradle to
charge.
Try a different position for the base unit –
somewhere higher if possible, or further from other
electrical equipment.
Try moving the handset closer to the base unit.
Check that the base unit’s mains power adapter
is plugged in and power is switched on.
Check that ring volume is not on OFF
You may be going out of range of the base unit.
Move closer or your call may be cut off.
Check the Battery Level symbol on the display. If
it’s low, recharge the batteries.
If you’re using a multi-handset system, check
whether another handset is already on a call.
Make sure you’re holding the earpiece correctly
over your ear.
Adjust the volume using the UP/DOWN key.
Before you first use the handset, you should have
left it on the base unit or charger pod for 15 hours
to charge the batteries fully. You may need to
replace the batteries. Check the connection
between the base unit and the mains power
socket. unit.
You need to replace the batteries. Dispose of
used batteries safely – never burn them, or put
them where they could get punctured. Do not use
non-rechargeable batteries in your handset – they
may explode, causing damage.
Disconnect all other instruments connected to the
same line and try to make a call.
Disconnect the base unit from the telephone line
and plug a different phone into the master
telephone socket. Try making a call. If this works,
the line is OK.
If the call does not work, and you are using a
two-way socket adapter, remove it and plug a
telephone directly into the socket.
If the call now works, the adapter may be faulty. If
you cannot make a call, the fault may be on the
exchange line. Contact the service provider.
“When I key in a number, it
appears on the display, but I
cannot make an outside call”
Product specificaties
| Merk: | Alcatel |
| Categorie: | Telefoon |
| Model: | Versatis E100 |
Heb je hulp nodig?
Als je hulp nodig hebt met Alcatel Versatis E100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Telefoon Alcatel
16 November 2024
3 September 2024
3 September 2024
3 September 2024
27 Augustus 2024
18 Juni 2024
18 Juni 2024
18 Mei 2024
18 Mei 2024
30 Juni 2023
Handleiding Telefoon
- Telefoon Philips
- Telefoon Sony
- Telefoon Samsung
- Telefoon Xiaomi
- Telefoon Panasonic
- Telefoon LG
- Telefoon Huawei
- Telefoon Asus
- Telefoon AEG
- Telefoon Fysic
- Telefoon Grundig
- Telefoon Gigaset
- Telefoon JBL
- Telefoon Motorola
- Telefoon Medion
- Telefoon Nokia
- Telefoon Pioneer
- Telefoon Siemens
- Telefoon Topcom
- Telefoon Toshiba
- Telefoon VTech
- Telefoon Wiko
- Telefoon Yamaha
- Telefoon Yealink
- Telefoon Aastra
- Telefoon Acer
- Telefoon AGFEO
- Telefoon Airis
- Telefoon Airlive
- Telefoon Alcatel-Lucent
- Telefoon Allview
- Telefoon Amplicom
- Telefoon Amplicomms
- Telefoon Anker
- Telefoon Apple
- Telefoon Archos
- Telefoon Ascom
- Telefoon Audio-Technica
- Telefoon Audioline
- Telefoon Auerswald
- Telefoon Avaya
- Telefoon AVM
- Telefoon Belgacom
- Telefoon Binatone
- Telefoon Blackberry
- Telefoon Blaupunkt
- Telefoon BT
- Telefoon D-Link
- Telefoon Davolink
- Telefoon Denver
- Telefoon Doro
- Telefoon Draytek
- Telefoon Emporia
- Telefoon Engenius
- Telefoon Envivo
- Telefoon Fenton
- Telefoon Flex
- Telefoon GE
- Telefoon Geemarc
- Telefoon Gigaset Pro
- Telefoon GPO
- Telefoon Grandstream
- Telefoon Hagenuk
- Telefoon Hama
- Telefoon Hitachi
- Telefoon Honor
- Telefoon HTC
- Telefoon HUMANTECHNIK
- Telefoon Innovaphone
- Telefoon KONFTEL
- Telefoon KPN
- Telefoon Kyocera
- Telefoon Lenovo
- Telefoon LevelOne
- Telefoon Lexibook
- Telefoon Linksys
- Telefoon Loewe
- Telefoon Logicom
- Telefoon Logik
- Telefoon Logitech
- Telefoon Mackie
- Telefoon Marmitek
- Telefoon Marquant
- Telefoon Marshall
- Telefoon Maxcom
- Telefoon Microsoft
- Telefoon Mikrotik
- Telefoon Mitel
- Telefoon MT Logic
- Telefoon Nec
- Telefoon Netgear
- Telefoon Nordmende
- Telefoon Parrot
- Telefoon Patton
- Telefoon Peaq
- Telefoon Pixel
- Telefoon Plantronics
- Telefoon Polycom
- Telefoon Premier
- Telefoon Prestigio
- Telefoon Profoon
- Telefoon Proximus
- Telefoon Pyle
- Telefoon Ranex
- Telefoon RCA
- Telefoon Realme
- Telefoon Renkforce
- Telefoon Roland
- Telefoon RugGear
- Telefoon Sagem
- Telefoon Sagemcom
- Telefoon Sencor
- Telefoon Sennheiser
- Telefoon Silvercrest
- Telefoon SMC
- Telefoon Snom
- Telefoon Spectralink
- Telefoon Sunstech
- Telefoon Sweex
- Telefoon Swissvoice
- Telefoon Switel
- Telefoon Sylvania
- Telefoon TCL
- Telefoon Tecdesk
- Telefoon Telefunken
- Telefoon Telstra
- Telefoon Thomson
- Telefoon Tiptel
- Telefoon Trendnet
- Telefoon Tristar
- Telefoon Trust
- Telefoon Uniden
- Telefoon Unify
- Telefoon Viking
- Telefoon Zebra
- Telefoon ZTE
- Telefoon ZyXEL
- Telefoon Jabra
- Telefoon Jacob Jensen
- Telefoon Olympia
- Telefoon OnePlus
- Telefoon Oppo
- Telefoon Oregon Scientific
- Telefoon Overmax
- Telefoon Essentiel B
- Telefoon Bang And Olufsen
- Telefoon BeeWi
- Telefoon CSL
- Telefoon Krüger And Matz
- Telefoon Steren
- Telefoon Ubiquiti Networks
- Telefoon Crosley
- Telefoon Infiniton
- Telefoon MXL
- Telefoon Hamlet
- Telefoon Edenwood
- Telefoon Trevi
- Telefoon Scosche
- Telefoon Oricom
- Telefoon AT&T
- Telefoon AudioCodes
- Telefoon Chacon
- Telefoon Valcom
- Telefoon SPC
- Telefoon Canyon
- Telefoon Cisco
- Telefoon Teledex
- Telefoon EVOLVEO
- Telefoon CAT
- Telefoon Oukitel
- Telefoon 3Com
- Telefoon Planet
- Telefoon Cubot
- Telefoon Clarity
- Telefoon Xblitz
- Telefoon VXi
- Telefoon Lindy
- Telefoon AVerMedia
- Telefoon Fortinet
- Telefoon Bogen
- Telefoon ArtDio
- Telefoon XD Enjoy
- Telefoon CTA Digital
- Telefoon MyPhone
- Telefoon Fanvil
- Telefoon Crestron
- Telefoon Yeastar
- Telefoon JPL
- Telefoon OpenVox
- Telefoon Gamdias
- Telefoon Primare
- Telefoon Syco
- Telefoon Edge-Core
- Telefoon Vimar
- Telefoon Akuvox
- Telefoon Legrand
- Telefoon Digium
- Telefoon Clear Sounds
- Telefoon Mitsai
- Telefoon ALLO
- Telefoon On-Q
- Telefoon Lewitt
- Telefoon Tecno
- Telefoon Vogtec
- Telefoon Olitech
- Telefoon Dopod
- Telefoon Sedna
- Telefoon British Telecom
- Telefoon CyberData Systems
- Telefoon Cortelco
- Telefoon Bintec-elmeg
- Telefoon Wantec
- Telefoon Neat
- Telefoon Algo
- Telefoon Future Call
- Telefoon 4family
- Telefoon Tador
- Telefoon Dnake
- Telefoon Liam&Daan
- Telefoon FlyingVoice
Nieuwste handleidingen voor Telefoon
17 November 2024
17 November 2024
17 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
16 November 2024
15 November 2024