Alcatel Sigma 260 Voice DUO Handleiding

Alcatel Telefoon Sigma 260 Voice DUO

Lees hieronder de 📖 handleiding in het Nederlandse voor Alcatel Sigma 260 Voice DUO (4 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

USER'S GUIDE

ATLINKS Europe, 22 quai Gallieni 92150 Suresnes – France

Alcatel Logo and Alcatel name are trademarks of Alcatel Lucent and

used under license by Atlinks.

Phone Function Keys

Base station

HANDSET LOCATOR button

Press to page handsets.

Press and hold to start registration procedure.

What’s on the display?

A Display Icons

B Displays when in menu mode to confirm your selection.

C Indicates that more options are available.

Use the UP / DOWN keys to scroll up / down.

D Displays when in menu mode.

Select BACK to return to the previous menu level.

Select BACK to delete the last digit / character entered.

What the icons mean?

Read First Before Use

Choosing a site for the base unit and charger pod

If you have a Broadband line

If you connect your telephone to a line with a broadband connection, you

will need to insert a microfilter between the telephone and the telephone

line, otherwise you may get interference between the telephone and the

broadband, which could cause problems.

Battery safety - CAUTION

ONLY use the rechargeable batteries supplied with the handset.

DO NOT use non-rechargeable batteries - they may explode and cause

damage to your telephone.

Only use rechargeable batteries with exactly the same specifications as those

supplied with the product.

Using non-rechargeable or non-conforming batteries can damage the product

and could pose a health hazard (see “Technical details”).

Failure to comply with this recommendation will invalidate the manufacturer's

warranty.

Batteries can split or leak if incorrectly inserted, opened or exposed to heat.

Never dispose of batteries in a fire: they could explode.

Installation and Set-up

Precautions

The signal quality will depend on the location and environment of the base

and handset. Position your Sigma 110 / Sigma 260 away from sources of

excessive heat (radiators, direct sunlight, etc.) and protect it from

vibrations and dust. Never allow your telephone to come into contact with

water or other liquids, or with aerosols. To reduce the risk of interference

and optimize reception, take particular care not to install the base in the

immediate vicinity of windows, large metal objects, reinforced concrete,

televisions, music centres, VCR or DVD players, halogen lamps or heating

devices, fluorescent lighting, burglar alarms, microwave ovens, computers,

etc.

This telephone requires an electrical power supply in order to function.

To clean your Sigma 110 / Sigma 260, use an antistatic cloth lightly

moistened with water.

NB: Your Sigma 110 / Sigma 260 is a DECT™* standard appliance

designed to receive and transmit telephone calls. It is designed for

connection to the public telecommunications network.

Fit the rechargeable batteries in each handset

1) Install the AAA batteries (Brand name: CORUN, Capacity: Ni-MH 1.2V/

400mAh, or Brand name: SANIK, Capacity: Ni-MH 1.2V / 400mAh) into

handset in accordance with the polarity marked in the battery

compartment.

2) Close the battery compartment cover, sliding it into place and pressing

firmly to make sure it is secure.

Connecting AC (electrical) power

1. Plug the base adaptor cord into the power jack on rear panel of the

base and the other end into a 100-240 Vac 50-60Hz electrical outlet.

2. Connect telephone line cord into the phone jack on rear panel of the

base and the other end into a main socket.

3. In case of twin or triple system, plug the charger power adaptor cord into

the power jack on rear panel of charger and the other end into a

100-240 Vac 50-60Hz electrical outlet.

Before you use the cordless handset for the first time, it’s important to

charge the batteries fully.

Leave the handset on the charging cradle for 15 hours.

CAUTION: Use only the power supply that came with this unit. Using other

power supplies may damage the unit.

Base and charger power adaptor :

S003IV0600050 100-240V 6V DC 500mA

S003IV0600015 100-240V 6V DC 150mA

Add/edit direct access memory

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK PHONEBOOK

key to select.

3. Press NAVIGATION key to select . and then press OK DIRECT MEM

key to select.

4. Press NAVIGATION key to select or and then press OK KEY 1 KEY 2

key.

The stored name is displayed, or if it is empty.NO NUMBER

If there is no number stored for the selected key or if you want to

change the name or number currently stored, press MENU key to

enter direct memory menu to add/edit the name or number.

5. Press NAVIGATION key to select and then press OK EDIT NUMBER

key to select. The display shows the currently stored name, or

ENTER NAME if there is no number stored. Edit or enter the name

you want and then press OK key. The display shows the currently

stored number, or if there is no number stored. ENTER NUMBER

Edit or enter the number you want and then press OK key to confirm.

A confirmation beep is played.

Delete direct access memory

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK PHONEBOOK

key to select.

3. Press NAVIGATION key to select . and then press OK DIRECT MEM

key to select.

4. Press NAVIGATION key to select or and then press OK KEY 1 KEY 2

key.

The stored name is displayed (or if it is already empty).NO NUMBER

5. Press MENU key to enter direct memory menu.

6. Press NAVIGATION key to select and then press OK key toDELETE

select.

Press OK key again to confirm. A confirmation beep is played.

Using the redial list

The redial list stores the last 5 numbers dialed.

Access redial list

1. Press REDIAL key in idle mode and press NAVIGATION key to

browse the redial list. The last number dialed will appear first in the

redial list.

2. Press OK key to view the details of the selected entry.

Save a redial number into the phonebook

1. Press REDIAL key in idle mode to go to the redial list.

2. Press NAVIGATION key to select an entry.

3. Press MENU key to display SAVE NUMBER, then press OK key to

display . Enter the name of the contact (maximum 12 ENTER NAME

characters) and then press OK key to save the entry, and return the

display to the redial list.

Using the call log

To receive Caller ID you may need to contact your telephone service

provider, and they will inform you also of any charges for it. Caller ID lets

you see the phone numbers of your callers on the handset display,

before answering and in your Call Log afterwards. The Call Log stores

the last 10 external calls, whether or not you answered the call, so you

can call them back later.

Only the most recent call is saved if there are repeat calls from the same

number. When the Call Log is full, the next new call will replace the

oldest entry.

If you've got a new call in the Call Log, will appear on the handset

display.

If the received number is the same as one in your phonebook, the name

from the phonebook will display as well as the number.

If a call is from someone who withheld their number, the display will

show .WITHHOLD ID

If the call is from someone whose number is unavailable, or if you have

not subscribed to Caller ID but have set the date and time, the display

will show when it is received and CALLING UNAVAILABLE in the Call

Log.

Access call log

Press in idle mode and press NAVIGATION key to browse the call list.

The calls are displayed in chronological order with the most recent call

at the top of the list.

Press OK key to display more details of the call, including the date and

time.

Save call list entry into the phonebook

1. Press in idle mode to go to the call list.

2. Press NAVIGATION key to select an entry and then press MENU key.

3. Press NAVIGATION key to select SAVE NUMBER and then press OK

key to select. (Enter the name of the contact (maximum 12 characters)

and then press OK key to confirm.)

Delete a Call Log entry

1. Press in idle mode to go to the call list.

2. Press NAVIGATION key to select an entry and then press MENU key.

3. Press NAVIGATION key to select and then press OK key to DELETE

select. (Press OK key again to confirm. A confirmation beep is played.)

Delete all entries in the Call Log

1. Press in idle mode to go to the call list.

2. Press MENU key.

3. Press NAVIGATION key to select and then press OK DELETE ALL

key to select. (Press OK key again to confirm. A confirmation beep is

played.)

Access phonebook

1. Press in idle mode to browse the phonebook entries. Alternatively,

you can press MENU key, to display and then press OK.PHONEBOOK

2. Press NAVIGATION key to select and then press OK key to confirm.LIST

The phonebook entries will be listed in alphabetical order, and you can

press NAVIGATION key to scroll through the stored entries.

3. Press OK key to view the details of the selected entry.

Note: Instead of pressing NAVIGATION key to browse the phonebook

entries, you can press the numeric key corresponding to the first letter of

the entry you wish to locate.

Modify a phonebook entry

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK key PHONEBOOK

to select.

3. Press NAVIGATION key to select and then press OK key EDIT ENTRY

to select.

4. Press NAVIGATION key to select an entry to edit and then press OK key.

The current name is displayed.

Edit the name and then press OK key to confirm.

5. Edit the number and then press OK key to confirm. A confirmation beep

is played.

Delete a phonebook entry

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK keyPHONEBOOK

to select.

3. Press NAVIGATION key to select and then press OK key toDELETE

select.

4. Press NAVIGATION key to select an entry to delete and then press OK

key.

5. Press OK key again to confirm. A confirmation beep is played.

Delete all entries from the phonebook list

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK key PHONEBOOK

to select.

3. Press NAVIGATION key to select and then press OK key DELETE ALL

to select.

4. Press OK key again to confirm. A confirmation beep is played.

Direct access memory

There are 2 direct access memories (Keys 1 & 2) in addition to the

phonebook memory. A long press on the keys in idle mode will

automatically dial the stored phone number.

Use handsfree (only for Sigma 260)

Press TALK key at any moment in normal talk mode to talk in handsfree

mode.

To deactivate the handsfree mode, press again the TALK key to talk in

normal talk mode.

Adjust the earpiece volume

During a call, press NAVIGATION key to select from VOLUME 1 to

VOLUME 3.

Mute/unmute microphone

When the microphone is muted, the handset displays , and your MUTE ON

caller cannot hear you.

During a call, press the MUTE key to turn on/off the microphone.

Your Telephone Operations

Switching on/off

Press and hold the HANG-UP/EXIT key for more than 2

seconds to switch on/off the handset in idle mode.

Notes: When the handset is OFF, it cannot be used for making calls

including emergency calls. There will be no ringing during an incoming call.

To answer a call, you will need to switch it back on. It may take some time

for the handset to re-establish a radio link with the base unit.

To lock/unlock the keypad

Press and hold the STAR key for 1 second to lock/unlock the

keypad in idle mode.

Note: Incoming calls can still be answered even if the keypad was locked.

Set time and date

Note: If you subscribe to the Caller Display service, the time and date will

be set automatically when you receive a call, but you may still need to set

the correct year.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK CLOCK&ALARM

key to select.

3. Press OK key to select DATE/TIME. The last stored date is displayed.

Enter the current date (YY-MM-DD), press OK, then enter the time

(HH-MM).

Change your handset’s name

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK PERSONAL SET

key to select.

3. Press NAVIGATION key to select and then press OK HANDSET NAME

key to select. The current handset name is displayed.

4. Press BACK/CLEAR key to delete the characters one by one.

Enter the new name (maximum 10 characters) and press OK key to

confirm.

A confirmation beep is played.

Change the display language

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK PERSONAL SET

key to select.

3. Press NAVIGATION key to select and then press OK key LANGUAGE

to select.

4. Press NAVIGATION key to your desired language and press OK key to

confirm. A confirmation beep is played.

Note: Once the display language is set, the option menus on the handset

will switch to display in the selected language immediately.

Make and answer calls

Make a callPredialling

Dial the number (maximum 24 digits) and then press TALK key.

Direct dialling

Press TALK key to take the line and then dial the number

(maximum 24 digits).

Call from redial list

Press REDIAL key in idle mode.

Press NAVIGATION key to select an entry in the redial list and

then press TALK key.

Call from the call log

Press in idle mode.

Press NAVIGATION key to select an entry in the call list and

then press TALK key.

Note: You need to subscribe to Caller Line Identification service to be able

to see the caller’s number or name in the call log.

Call from the phonebook

Press in idle mode.

Press NAVIGATION key to select an entry in the phonebook and

then press TALK key.

Answer and end a call

1. When the phone rings, press TALK key. You can also use handsfree

mode thanks to a long press on TALK key (only on Sigma 260).

2. To end a conversation, press HANG-UP/EXIT key.

IMPORTANT NOTE: You can simply place the handset back on its base

station or charger pod to end the call.

Paging

The paging feature enables you to locate a missing handset if the handset

is in range and contains charged batteries.

Press HANDSET LOCATOR key located at the back of the base

station. All the registered handsets start to ring.

Once retrieved, press any key on the handset or the HANDSET

LOCATOR key again to end the paging.

Call waiting

If you have subscribed to Call Waiting service, the earpiece will emit a

beep tone to inform you that there is a second incoming call. The number

or name of the second caller will also be displayed on your phone if you

have subscribed to Caller Line Identification service (CLI). Please contact

your network provider for more information on this service.

Using your phonebook

Your phone can store up to 50 phonebook memories.

How to enter characters?

When you select a field in which you can enter text, you can enter the

letters that are printed on the keys by pressing the relevant key once or

several times.

For example, press once to insert the letter ‘A’, press twice to

insert the letter B, and so on... Spaces and other symbols can be entered

using or .

Store a contact in the phonebook

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press OK key PHONEBOOK

to select.

3. Press OK key again to enter .NEW ENTRY

4. Enter the name of the contact (maximum 12 characters).

To edit, press BACK/CLEAR key to delete the last character entered.

Press OK key to confirm the name entry.

5. Enter the number of the contact (maximum 24 digits) and then press OK

key to confirm. A confirmation beep is played.

Unpacking your phone

In the box you will find:

 the cordless handset (two handsets with a Twin system, and three

with a Triple system)

WKHEDVHXQLW

WZRUHFKDUJHDEOHEDWWHU\FHOOVIRUHDFKKDQGVHW

DEDWWHU\FRPSDUWPHQWFRYHUIRUHDFKKDQGVHW

DWHOHSKRQHOLQHFDEOHIRUWKHEDVHXQLW

DPDLQVSRZHUOHDGDQGDGDSWHUIRUWKHEDVHXQLW

FKDUJHUSRGVHDFKZLWKDQDWWDFKHGPDLQVSRZHUOHDGDQGDGDSWHU

for multihandset system

Before you start to use your telephone make sure that all batteries are

fully charged for 15 hours.

Important note: This telephone is not designed for Emergency calls

when the mains power fails.

For Emergency calls you should have a basic phone that operates

without mains power, connected to your line so that you can make calls

during a power failure.

1OK / Menu key

Press to select the function displayed on the handset screen directly

above it.

Press to access the main menu.

2Back / Mute key

Press to delete a digit / a character in editing mode

Press to return to idle mode.

Press and hold to change the handset idle display between handset

name and date / time.

Press to mute / unmute the handset microphone.

3Navigation key

Press UP to access the call log* and press DOWN to access the

phonebook when in idle mode.

Press UP / DOWN to increase or decrease earpiece volume during a call.

Press to increase or decrease the ringer volume.

Press UP / DOWN to increase or decrease handsfree volume

(Sigma 260 only)

Scroll up / down a list.

4Talk key

Press to accept or make a call

Press to activate handsfree mode (Sigma 260 only)

5Hang-up / Exit key

Press and hold to switch the handset power on / off .

Press to end a call.

Press to return to idle mode in other menus.

6Call transf er / Intercom key

Press to initiate an internal call.

Press to hold the line and page another handset during a call.

Press and hold to initiate a conference call.

7Recall (Flash) key

Access to operator services*

8Redial key

Press to access the Redial list.

9Star key

Press and hold to lock / unlock keypad.

Press and hold to toggle between the external and internal calls when both are set up.

10 Hash key

Press and hold to insert a pause during a call.

Press and hold to turn the ringer on / off.

*Subject to subscritption and availability of the service from the f ixed line operator.

Indicates battery is fully charged.

Indicates battery is fully discharged.

Indicates that an external call is connected or held.

Icon blinks when receiving an incoming call.

Indicates you have a new Voice Mail message*.

Indicates you have new missed calls*, or the call log is being viewed.

Displays when the phonebook is accessed.

Displays when the alarm clock is activated.

Displays when handsfree is activated (Sigma 260 only).

Displays when ringer volume is turned off.

Indicates that the handset is registered and within range of the base station.

Icon blinks when the handset is out of range or is searching for a base.

Displays when in menu mode to confirm your selection.

Indicates that more options are available.

Use the UP / DOWN keys to scroll up / down.

Displays when in menu mode.

Select BACK to return to the previous menu level.

B D

Troubleshooting

If you have difficulty with your phone, please try the suggestions listed

below.

As a general rule, if a problem occurs, remove the batteries from all the

handsets in your installation for about 1 minute, then disconnect and

reconnect the power supply to the base and reinstall the handset batteries.

Always :check first that

Everyday use

“I cannot make or answer

calls”

You have followed all the steps listed in the user

manual to install and set up your telephone.

All connectors are firmly inserted in their sockets.

Mains power to the base unit is switched on at the

socket.

The handset’s batteries are correctly and securely

installed and are not run down.

If the handset’s display is blank, it may have been

switched off. Press and hold the HANG-UP/EXIT

key to switch it back on.

Check that the base unit’s mains power adapter is

plugged in and power is switched on.

The base unit needs mains power for normal

operation of the phone - not just for charging the

batteries.

Make sure you are using the telephone line cable

supplied with your telephone. Other telephone line

cables might not work. Move the handset closer to

the base unit.

Check the battery level symbol on the display. If it

is low, replace the handset on the base unit or

charger pod to recharge the batteries.

Switch off power at the mains socket, wait for a

short time and then switch back on. This may

solve the problem.

“I cannot make a call”

“When I press on the

keys, nothing happens”

“When I key in a number,

it appears on the display,

but I cannot make an

outside call”

“The phone does not

ring”

“I hear ‘beeps’ from my

handset while I’m on a

call”

“When I try to make a call,

I hear busy tone”

“The volume in the

earpiece is low when I’m

on a call”

If the handset display shows KEYS LOCKED,

press and hold the * button to unlock it before you

make a call.

Only one handset (or the base unit) can be

connected to the outside line at a time. If another

handset is already using the line, you need to wait

until it has finished its call.

Make sure the batteries are fitted in your handset

If the Battery Level symbol on the display shows

‘low’, put your handset back on the cradle to

charge.

Try a different position for the base unit –

somewhere higher if possible, or further from

other electrical equipment.

Try moving the handset closer to the base unit.

Check that the base unit’s mains power adapter

is plugged in and power is switched on.

Check that ring volume is not on OFF.

You may be going out of range of the base unit.

Move closer or your call may be cut off.

Check the Battery Level symbol on the display. If

it’s low, recharge the batteries.

If you’re using a multi-handset system, check

whether another handset is already on a call.

Make sure you’re holding the earpiece correctly

over your ear.

Adjust the volume using the UP/DOWN key.

Batteries

“The handset’s battery

cells are running low

within an hour or two”

“I try to recharge the

batteries but I still get a

warning that they are

low”

If the fault persists...

Before you first use the handset, you should have

left it on the base unit or charger pod for 15 hours

to charge the batteries fully. You may need to

replace the batteries. Check the connection

between the base unit and the mains power

socket unit.

You need to replace the batteries. Dispose of

used batteries safely – never burn them, or put

them where they could get punctured. Do not use

non-rechargeable batteries in your handset – they

may explode, causing damage.

Disconnect all other instruments connected to the

same line and try to make a call.

Disconnect the base unit from the telephone line

and plug a different phone into the master

telephone socket. Try making a call. If this works,

the line is OK.

If the call does not work, and you are using a

two-way socket adapter, remove it and plug a

telephone directly into the socket.

If the call now works, the adapter may be faulty. If

you cannot make a call, the fault may be on the

exchange line. Contact the service provider.

The store where you bought your telephone can also provide you with

information and after-sales support.

Set alarm tone

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press CLOCK&ALARM

OK key to select.

3. Press NAVIGATION key to select ALARM TONE and then press OK

key to select.

4. Press NAVIGATION key to select MELODY 1 MELODY 2, or

MELODY 3 and then press OK key to confirm. A confirmation beep is

played.

Advanced use of your telephone

Change Master PIN

The Master PIN is used for registration/unregistration of handsets.

The default Master PIN number is 0000. The maximum length of the

Master PIN is 8 digits.

Note: If you forget your PIN code, you can reset it to its default 0000

using a handset Reset (see section Reset Unit).

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select ADVANCED SET and then press

OK key to select.

3. Press NAVIGATION key to select and then press OK CHANGE PIN

key to select.

Enter the current Master PIN when prompted and then press OK key to

confirm.

As you enter the PIN it will be shown as asterisks (*) on the screen.

(Enter the new PIN and then press OK key to confirm. A confirmation

beep is played.)

IMPORTANT: When you purchase a telephone, all handsets are already

registered to the base, so you do not need to register them. Handset

registration is only necessary when you buy extra handsets or if a

handset has become faulty.

The procedure described below is for Sigma 110 or Sigma 260.

They may be different if you want to register another handset model, in

which case you should refer to its user guide.

Additional handsets must be registered to the base unit before you can

use them. Up to 4 handsets can be registered to one base station.

The Master PIN is required before you can register or unregister

handsets.

By default, the Master PIN is 0000.

On the base station, press and hold the HANDSET LOCATOR key for

approximately 5 seconds.

5. Press NAVIGATION key to select or and then press OK key ON OFF

to confirm. A confirmation beep is played.

Activate/deactivate auto hang-up

This function enables you to end a call automatically by simply placing

the handset on the base station. By default, the Auto Hang up feature is

ON.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select PERSONAL SET and then press

OK key to select.

3. Press NAVIGATION key to select AUTO HANG-UP and then press

OK key to select.

4. Press NAVIGATION key to select or and then press OK key ON OFF

to confirm. A confirmation beep is played.

Set date/time format

You can set your preferred date/time format for your phone. The default

format is DD/MM and 24 HOURS.

Set time format

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press CLOCK&ALARM

OK key to select.

3. Press NAVIGATION key to select SET FORMAT and then press OK

key to select.

4. Press OK key to enter TIME FORMAT. The current setting is displayed.

5. Press NAVIGATION key to select or and then12 HOURS 24 HOURS

press OK key to confirm. A confirmation beep is played.

Set date format

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press CLOCK&ALARM

OK key to select.

3. Press NAVIGATION key to select SET FORMAT and then press OK

key to select.

4. Press NAVIGATION key to select DATE FORMAT and then press OK

key to select. The current setting is displayed.

5. Press NAVIGATION key to select or and then press DD/MM MM/DD

OK key to confirm. A confirmation beep is played.

Set alarm

The handset has an alarm clock feature, and when the alarm is set,

the is shown on the handset display.

When the alarm time is reached, the display flashes -- -- and the ALARM

alarm melody is played for 1 minute or until any handset key is pressed.

If the alarm is set for ON DAILY and the alarm will sound again on the

next day.

If the alarm was set for ON ONCE, the will be turned off.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select and then press CLOCK&ALARM

OK key to select.

3. Press NAVIGATION key to select and then press OK key to ALARM

select.

4. Press NAVIGATION key to select , or OFF ON ONCE ON DAILY and

then press OK key to confirm.

If you select or ON ONCE ON DAILY, enter the time (HH-MM) for the

alarm and press the UP/DOWN key to select AM or PM if the time is

in 12 HOURS format.

5. Press OK key to confirm. A confirmation beep is played.

1. On the handset, press MENU key to enter menu selection.

2. Press NAVIGATION key to select ADVANCED SET and then press OK

key to select.

3. Press NAVIGATION key to select REGISTRATION and then press OK

key to select.

Note: If no action is taken on the handset within 10 seconds, the

registration procedure will be aborted. If this happens, repeat the first step.

WAITING is displayed on the screen. A confirmation beep is played to

indicate successful registration, and the handset will return to idle mode,

with its handset number displayed.

Note: If no base is found within a certain period, will be NO BASE

displayed with an error tone to indicate failed registration and the handset

returns to idle mode, and you will need to repeat the registration sequence.

Unregister your handset

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select ADVANCED SET and then press OK

key to select.

3. Press NAVIGATION key to select and then press OK keyUNREGISTER

to select.

4. Enter the Master PIN when prompted and then press OK key to confirm.

(the default master PIN is 0000)

5. Press NAVIGATION key to select the handset number to unregister and

then press OK key to confirm.

A confirmation beep is played to indicate successful unregistration.

Note: If no action is taken on the handset within 15 seconds, the

unregistration procedure will be aborted and the handset returns to idle

mode.

You must use another handset to unregister handsets from the base.

Change recall time

You may need the R button to send a Recall signal (also called Flash or

Timed Break Recall) if you are connected to a PBX. You should normally

leave the Recall Time at its default setting of Short (100ms), as this is the

standard recall required in the telephone network, but it can be changed to

Medium (270ms) or Long (600ms) if your telephone is connected to a PBX

that requires a different recall time.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select ADVANCED SET and then press OK

key to select.

3. Press NAVIGATION key to select RECALL TIME and then press OK

key to select.

4. Press NAVIGATION key to select , or and then SHORT MEDIUM LONG

press OK key to confirm. A confirmation beep is played.

Reset unit

You can reset your phone to its default settings with this feature.

Note: Upon reset, all your personal settings, call log and redial list entries

will be deleted and the phone will return to its default settings. However,

your phonebook will remain unchanged after reset.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select ADVANCED SET and then press OK

key to select.

3. Press NAVIGATION key to select and then press OK key to RESET

select.

4. Press OK key again to confirm. A confirmation beep is played and the

unit is reset to its default settings.

* Value may vary according to environment.

** Depending on initial battery charge.

Technical details

Free field range

Indoor range

Handset battery life

(average values)

Number of handsets

Intercom mode

Three -way confere

(1 outside correspondent +

2 internal correspondents)

Electrical connection /

Base mains adapter /

Charger

Telephone connection

Batteries

Operating temperature

Up to 300 meters*

Up to 50 meters*

7 hours talktime**

100 hours standby**

Up to 4

Yes

Base: S003IV0600050

Charger: S003IV0600015

Input: 100-240 V / 50-60 Hz

Output: 6V DC / 500mA(BASE)

6V DC / 150mA (Charger)

Only use the adapters supplied with the

telephone.

Single-phase AC, excluding IT installations

defined by the EN 60950 standard. Caution:

the network voltage is classified as a hazard

by the criteria of this standard.

Appliance designed for connection to a

TNV3 class (telecommunications network

voltage) analogue telephone line as defined

by the EN 60950 standard.

Corun / Sanik – AAA – 1.2 V – 400mAh

Only use the batteries supplied with the

telephone.

Using any other type of battery presents a

risk of explosion.

Used batteries must be disposed of in

compliance with current environmental

protection regulations.

From 5 to 40° C

Safety

In the event of an electrical hazard, the mains adapter acts as 230V

power isolating device. It should therefore, as a precaution, be installed

close to the appliance and be easily accessible. To disconnect the

device from the primary power source, the mains adapter must be

removed from the 230V AC/50 Hz socket.

If the mains adapter fails, it must be replaced by an identical model.

If not connected to the mains power or if there is a mains power failure,

telephones that use cordless handsets will not work.

You will then be unable to make or receive calls in the event of an

emergency.

This is why we recommend that you also keep a conventional telephone

– one that doesn’t require a power supply – as a backup.

! Do not use your telephone to notify a gas leak when standing in

the vicinity of the leak.

It is recommended that you avoid using this device during electrical

storms.

Do not attempt to open the batteries, as they contain chemical

substances.

In the event of leakage, avoid contact with the skin, eyes, nose and

mouth.

In the event of contact, rinse the affected part for about twenty minutes

with running water and seek urgent medical attention.

Clean the product with absorbent paper or a dry cloth and contact your

reseller for replacement batteries.

ATLINKS hereby declares that the following models conform to the

essential requirements and other applicable provisions of European

directive 1999/5/EC.

Sigma 110 / Sigma 110 Duo / Trio

Sigma 260 / Sigma 260 Duo / Trio

Model Sigma 110 / 110 Duo / Trio

Sigma 260 / 260 Duo / Trio G2c

A/W No. : 10000576 Rev.1 (EN)

Made in China

ATLINKS, 22 quai Gallieni 92150 Suresnes – France

S.A.S. (Simplified Joined Stock Company) with capital of 500 000 Euros

- Registration number: 508 823 747 R.C.S. Nanterre.

The manufacturer reserves the right to modify the specifications of its

products in order to make technical improvements or comply with new

regulations.

ALCATEL and ATLINKS are registered trademarks.

The Alcatel logo and Alcatel name are trademarks of Alcatel Lucent and

used under license by ATLINKS.

Press TALK key on the called handset to answer the internal

call, where both internal callers can talk. Intercom is

established.

Press and hold INT key for 2 seconds on the first handset to

start the three-party conference.

CONFERENCE will be displayed on the screen once the conference call

is established.

Handset Tone

Set the ring volume

There are 5 ringer volume options (OFF, LEVEL 1, LEVEL 2, LEVEL 3

and LEVEL 4). The default level is LEVEL 2.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select PERSONAL SET and then press

OK key to select.

3. Press NAVIGATION key to select HANDSET TONE and then press

OK key to select and show . Press the OK key again RING VOLUME

to select.

4. Press NAVIGATION key to your desired volume level and then press

OK key to confirm. A confirmation beep is played.

Set the ring melody

There are 10 ring melodies available on your handset.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select PERSONAL SET and then press

OK key to select.

3. Press NAVIGATION key to select HANDSET TONE and then press

OK key to select.

4. Press NAVIGATION key to select RING TONES and then press OK to

select.

5. Press NAVIGATION key to your desired melody and then press OK

key to confirm. A confirmation beep is played.

Activate/deactivate key tone

A single tone is emitted when a key is pressed. You can enable or

disable the key tone. By default, the key tone is ON.

1. Press MENU key to enter menu selection.

2. Press NAVIGATION key to select PERSONAL SET and then press

OK key to select.

3. Press NAVIGATION key to select HANDSET TONE and then press

OK key to select.

4. Press NAVIGATION key to select KEY BEEP and then press OK to

select.

Using the intercom

Intercom, call transfer and conference are only possible with at least 2

handset registered to the same base station. It allows you to make free

internal calls, transfer external calls from one handset to another, and

set up a 3-way conference with two handsets and an external call.

If you try to make a call while another handset is already on an external

call, you'll hear a busy tone for a few seconds before the display returns

to idle.

Intercom another handset

Press INT key in idle mode.

Intercom is established immediately if there are only 2

registered handsets.

If there are more than 2 registered handsets, the handset numbers

which are available for intercom, and a * will be displayed. Press the

specific handset number you wish to call, or press to ring all

handsets, to start intercom.

Transfer an external call to another handset

During the call, press INT key to put the external call on hold

(the caller can no longer hear you).

Intercom is established immediately if there are only 2 registered

handsets.

If there are more than 2 registered handsets, the handset numbers

which are available for intercom, and a * will be displayed. Press the

specific handset number you wish to call, or press to ring all

handsets, to start intercom.

Press TALK key on the called handset to answer the internal

call, where both internal callers can talk. Intercom is

established.

Press HANG-UP/EXIT key on the first handset to transfer the

external call to the called handset. The external call is

transferred.

Note: If there is no answer from the called handset, press INT key to

resume the external call.

Answer an external call during intercom

During intercom, a new call tone is emitted when there is an incoming

external call.

Press TALK key to answer the external call and end the

intercom.

Connection with the external call is established.

Note: To put the internal call on hold and answer the incoming external

call, press INT key.

Switch between an internal and external call

During the call, press key to switch between an internal

orexternal call.

Establish a three-party conference call

The conference call feature allows one external call to be shared with

two handsets (in intercom). The three parties can share the conversation

and no additional network subscription is required.

During an external call, press INT key to put the external call

on hold (the caller can no longer hear you).

If there are more than 2 registered handsets, the handset numbers

which are available for intercom will be displayed. Press the specific

handset number you wish to call to start intercom.

ENVIRONMENT

This symbol means that your inoperative electronic appliance

must be collected separately and not mixed with the household

waste. The European Union has implemented a specific

collection and recycling system for which producers are responsible.

This appliance has been designed and manufactured with high quality

materials and components that can be recycled and reused. Electrical

and electronic appliances are liable to contain parts that are necessary

in order for the system to work properly but which can become a health

and environmental hazard if they are not handled or disposed of in the

proper way. Consequently, please do not throw out your inoperative

appliance with the household waste.

If you are the owner of the appliance, you must deposit it at the

appropriate local collection point or leave it with the vendor when buying

a new appliance.

- If you are a professional user, please follow your supplier's instructions.

- If the appliance is rented to you or left in your care, please contact your

service provider.

Keen to preserve the environment, ATLINKS has equipped this appliance

with a switching power supply, offering better energy efficiency.

The advantages include not only very low electricity consumption, but

also a more compact format than the conventional power supply units

used by the previous range.

The used batteries from your telephone (if it has batteries) must be

disposed of in compliance with current environmental protection

regulations.

Comply with your local regulations.

Return your batteries to your reseller or dispose of them at an approved

recycling centre.

Help us protect the environment in which we live!

www.alcatel-home.com

Product specificaties

Merk:	Alcatel
Categorie:	Telefoon
Model:	Sigma 260 Voice DUO
Kleur van het product:	Black, Green
Ingebouwd display:	Ja
Soort:	DECT-telefoon
Beeldscherm:	LED
Montagewijze:	Vloer
Microfoon mute:	Ja
Luidspreker:	Ja
Gesprek in de wacht zetten:	Ja
Nummerherkenning:	Nee
Conferentiegesprek mogelijk:	Ja
Volumeregeling:	Digitaal
Beeldscherm, aantal kleuren:	Monochroom
Inclusief basisstation:	Ja
Aansluiting voor netstroomadapter:	Ja
Batterij-indicator:	Ja
Standby tijd:	120 uur
Aantal knoppen:	21
Backlight toetsen:	Ja
Backlight-kleur:	Amber
Inclusief headset:	Nee
Type ringtone:	Polyfonisch
Klok met kalender:	Ja
Power over Ethernet (PoE):	Nee
Aantal melodieën:	10
Gesprekstijd:	8 uur
Capaciteit telefoonboek:	50 entries
Opnieuw bellen:	Ja
Afmetingen basisstation:	140 x 54 x 86 mm
Aantal handsets inclusief:	2
Navigatietoets:	Ja
LED op basisstation:	Ja
Draadloze verbindingen:	Ja
Pager functie:	Ja
Maximum indoorbereik:	50 m
Maximum outdoorbereik:	300 m
Antwoordapparaat:	Ja
Aantal handsets mogelijk:	4
Opnametijd:	15 min
Afmetingen handset (BxDxH):	47 x 62 x 30 mm
Geïntegreerde antenne:	Ja
Plaats toetsen:	Handset
Grote knoppen:	Ja
AC-ingangsspanning:	230 V
AC-ingangsfrequentie:	50 Hz
Batterijtechnologie:	Nikkel-Metaalhydride (NiMH)
Type batterij:	AAA
Display met achtergrondverlichting:	Ja
On-hook dialing:	Ja