Air King EVLD Handleiding

Air King Niet gecategoriseerd EVLD

Lees hieronder de 📖 handleiding in het Nederlandse voor Air King EVLD (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

www.airkinglimited.com6727916 Rev. H 12/21 1 of 16

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

SAVE THESE INSTRUCTIONS

Exhaust Fan with Light

EVLD Series

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electric shock and

injury to person, including the following:

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK AND INJURY TO

PERSON, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-related construction.

b) Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline

and safety standards such as those published by the National Fire

Protection Association (NFPA) and the American Society for Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI (Ground

Fault Circuit Interrupter) – protected branch circuit.

f) Do not install in a ceiling with thermal insulation value greater than

R40.

g) This unit must be grounded.

h) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

i) Read all instructions before installing or using exhaust fan.

j) Suitable for use with electronic speed control device.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT

ON THE AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE

THE SHORTEST, STRAIGHTEST DUCT ROUTING POSSIBLE FOR

BEST PERFORMANCE, AND AVOID INSTALLING THE FAN WITH

SMALLER DUCTS THAN RECOMMENDED. INSULATION AROUND

THE DUCTS CAN REDUCE ENERGY LOSS AND INHIBIT MOLD

GROWTH. FANS INSTALLED WITH EXISTING DUCTS MAY NOT

ACHIEVE THEIR RATED AIRFLOW.

www.airkinglimited.com6727916 Rev. H 12/21 2 of 16

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Exhaust Fan

1. Unpack fan from the carton and confirm that all pieces are present. In addition to the

exhaust fan you should have:

1 - Grill

1 - Damper Assembly (attached)

4 - Mounting Rails

1 - Mounting Flange

1 - LED Lamp

1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound performance, it is

recommended that the length of ducting and the number of elbows be kept to a minimum,

the radius of each elbow be as large as possible for the installation, and that insulated hard

ducting be used. Larger duct sizes will reduce noise and airflow restrictions. This fan will

require at least 10 of clearance in the ceiling or wall, and will mount through drywall up ”

to 3/4 thick.”

3. No additional vibration deadening materials are needed for this fan.

SECTION 2

New Construction

NOTE: If the mounting flange is installed on the fan housing, remove the two screws that connect

the ceiling mounting flange to the housing and set aside (Figure 17).

1. Install the rails into the mounting channel on the housing. Center the mounting channel in

the slots on the housing, then from inside the housing tighten the mounting channel nuts so

the channel is securely in place. Position the housing next to the joist. Line up housing so

that it will be flush with the finished ceiling. Secure the ends of the rails with screws or nails

(not included) to the joists and slide the housing into the final position (Figure 1).

SECTION 3

Existing Construction

NOTE: If the mounting flange is installed on the fan housing, remove the two screws that connect

the ceiling mounting flange to the housing and set aside (Figure 17).

1. Set housing in position between the joist and trace an outline onto the ceiling material

(Figure 2). Set housing aside and cut opening, being careful not to cut or damage any

electrical or other hidden utilities. Install the rails into the mounting channel on the

housing. Center the mounting channel in the slots on the housing, then from inside the

housing tighten the mounting channel nuts so the channel is securely in place. Position

the housing in the previously cut hole so that it is flush with the finished ceiling. Secure

the ends of the rails to the joists (Figure 1).

SECTION 4

Ducting

NOTE: 6" OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST PERFORMANCE.

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL

BUILDING CODES.

NOTE: The ducting from this fan to the outside of the building has a strong effect on the air

flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best

performance, and avoid installing the fan with smaller ducts than recommended. Insulation

around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing

ducts may not achieve their rated air flow.

1. Connect the ducting to the fan’s duct collar Secure in place using tape or screw (Figure 3).

clamp. Always duct the fan to the outside through a wall or roof cap. It is recommended

that low restriction termination fittings be used.

2. Ensure duct joints and exterior penetrations are sealed with caulk or other similar

material to create an air-tight path to minimize building heat loss or gain and to reduce

the potential for condensation. Place/wrap insulation around duct and/or fan to in order to

minimize possible condensation buildup within the duct, as well as building heat loss or

gain (Figure 4).

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL

WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not require the removal of the

fan’s blower assembly. If you choose to wire the unit from the inside, you will need to remove the

blower assembly and internal wiring compartment. Both methods are equally effective.

1a. External Wire Compartment: Remove the wire compartment cover screw and place cover

in a secure place (Figure 5).

Ducting

Duct

Collar

Figure 3

Figure 2

Joist

Housing

Joist

Mounting Rails

Figure 1

Figure 4

Insulation*

(place around and

over Fan Housing

Fan Housing

Power Cable*

Seal gaps

around Housing

Round

Duct*

Seal duct joints

with tape

Round

Elbows*

Wall Cap*

Roof Cap*

(with built-in

damper)

Keep duct

runs short

*Purchase separately

www.airkinglimited.com6727916 Rev. H 12/21 3 of 16

1b. Internal Wire Compartment: If the motor is already installed in the housing, remove the

two screws holding the blower assembly in place. Lift up on the assembly and slide it out

of the tabs on the housing . Remove the wire compartment cover screw and (Figure 6)

place the cover in a secure place (Figure 7).

NOTE: If the fan motor plug is connected to the fan housing receptacle, unplug so the blower

assembly can be completely removed.

Standard Models

2. Continuous Ventilation: Secure the electrical wires to the housing with an approved

electrical connector. For two speed fans wired for continuous ventilation, connect the White

wires of the fan to the White (Neutral) wire from the power source. Connect the ground wire

from the house to the green wire from the fan housing. Connect the Black wire of the fan

to the Black wire (Hot) from the power source. Using a properly grounded standard duplex

toggle switch (such as Leviton 5224-2W, not included) connect the Black wire from the

supply to one side of the top and bottom switch. Connect the Red wire (light) from the fan

housing to the other side of the top switch. Using a second properly grounded standard

duplex toggle switch, connect the Hot Yellow wire from the fan to the input of the switch.

Connect the second Yellow wire from the fan to the output side of the switch. Closing the

switch will change from normal to high speed (Figure 8).

NOTE: There may be more than one white fan wire that will need to be connected to the

white wire from the supply.

NOTE: The yellow wire may contain a wire crimp nut which will have to be cut off and the

wire stripped.

Motion Sensing Models

3. Secure the electrical wires to the housing with an approved electrical connector. For two

speed fans wired for continuous ventilation, connect the White wires of the fan to the White

(Neutral) wire from the power source. Connect the ground wire from the house to the green

wire from the fan housing. Connect the Black wire of the fan to the Black wire (Hot) from

the power source. The fan will operate on low speed continuously and boost to high speed

when motion is detected. Using a properly grounded standard duplex toggle switch (such

as Leviton 5224-2W, not included) connect the black wire from the supply to one side of

the top and bottom switch. Connect the red wire (light) from the fan housing to the other

side of the top switch. A manual override switch (not included) can be used to provide a

manual fan Off function (Figure 9).

NOTE: There may be more than one white fan wire that will need to be connected to the

white wire from the supply.

Humidity Sensing Models

4. Secure the electrical wires to the housing with an approved electrical connector. For two

speed fans wired for continuous ventilation, connect the White wires of the fan to the

White (Neutral) wire from the power source. Connect the ground wire from the house to

the Green wire from the fan housing. Connect the Black wire of the fan to the Black wire

(Hot) from the power source. The fan will operate on low speed continuously and boost

to high upon a rise in humidity. Using a properly grounded switch, connect 1 yellow wire

to each side of the switch. Closing the switch will change from normal to high speed.

Using a properly grounded standard duplex toggle switch (such as Leviton 5224-2W, not

included) connect the Black wire from the supply to one side of the top and bottom

switch. Connect the Red wire (light) from the fan housing to the other side of the top

switch. A manual override switch (not included) can be used to provide a manual fan Off

function (Figure 10).

NOTE: The yellow wire may contain a wire crimp nut which will have to be cut off and the

wire stripped.

Humidity and Motion Sensing Models

5. Secure the electrical wires to the housing with an approved electrical connector. For two