ADDAC System Acid Source ADDAC107 Handleiding

ADDAC System Niet gecategoriseerd Acid Source ADDAC107

Lees hieronder de 📖 handleiding in het Nederlandse voor ADDAC System Acid Source ADDAC107 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
Instruments for Sonic Expression
Est.2009
April.2023
USER’S GUIDE . REV01
ADDAC107
ACID
SOURCE
INTRODUCING
From Portugal with Love!
ADDAC107 ACID SOURCE USER’S GUIDE
April.2023Revision.01
Welcome to:
page 2ADDAC SYSTEM
DESCRIPTION
We started this module with the idea of developing a
complex drum source however, somewhere along the
process, we noticed how much better it performed as a
synth voice and simply embraced this lucky accident.
It features a VCO with a [FREQUENCY] and [FINE TUNE]
knob plus a dedicated CV Input and Attenuator knob
(tunable over 4 octaves).
The VCO waveform output is achieved by selecting either
a Triangle or Saw through a switch.
the selected waveform can then be mixed/balanced
against the square wave.
The resulting mix is then sent to the Filter.
The Filter features a [CUTOFF] and [RESO] resonance
knob plus a Cutoff CV Input and Attenuverter knob.
A 3 position switch is used to select the filter type:
Highpass, Bandpass or Lowpass.
The resulting output is then sent to the VCA.
The VCA features an Input with [INPUT GAIN] knob which
at maximum can amplify the incoming signal by a factor
of 2. This is a very important control (more about it in the
next page). It accepts any signal Trigger, Gate or CV.
Whatever input is plugged in the signal is then fed
through an AD with a very short attack and controllable
decay through the [VCA DECAY] knob plus the CV Input
and Attenuverter knob.
The resulting slewed signal is then used to control the
VCA gain. This signal is also sent to the CV OUTPUT as
well as the LED monitor.
The Accent input adds to the Input signal creating a
different amplitude output
The CV OUTPUT is also normalled to the Frequency and
Cutoff inputs.
This module will also be available as a full DIY kit. Tech Specs:
9HP
4 cm deep
80mA +12V
80mA -12V
page 3ADDAC SYSTEM
INPUT GAIN
The [INPUT GAIN] knob,
Usually Attack/Decay envelopes have a maximum
voltage of +5v, no matter if the input gate is +5v or
above the AD will clip at +5v. In this case we did not use
this clipping method and instead allow the incoming
voltage to determine the maximum AD voltage, meaning
that if a +5v gate is present then the AD maximum
voltage will be +5v but if a gate of +10v is sent then the
AD maximum voltage will be +10v.
This also means that with higher input voltages the
decay, although falling at the same speed, will be longer
than with lower voltages as it has a longer range to go
back to 0v.
As we mentioned before the [INPUT GAIN] knob can
amplify the incoming input by a factor of 2, allowing to
use a standard +5v gate or envelope and being able to
make the resultant AD go up to +10v.
The AD signal is responsible for opening the VCA.
Up to +5v the VCA will open to unity gain above this
value the VCA will start to amplify and eventually
saturate and distort.
This saturation will add harmonics to the signal which
will change it’s gentle timbrical nature to a more unique
and peculiar timbre that will make the module shine in
Acid contexts.
Adding high levels of Resonance or even filter self
oscillation in combination with high VCA saturation will
create even more harmonics that we highly encourage
the user to explore.
ADDAC107 User’s Guide


Product specificaties

Merk: ADDAC System
Categorie: Niet gecategoriseerd
Model: Acid Source ADDAC107

Heb je hulp nodig?

Als je hulp nodig hebt met ADDAC System Acid Source ADDAC107 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd ADDAC System

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd