ABB DY365 4CE Handleiding

ABB Niet gecategoriseerd DY365 4CE

Lees hieronder de 📖 handleiding in het Nederlandse voor ABB DY365 4CE (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/1
User manual
DY365 4CE REMOTE ACTUATOR
Read all instructions carefully
• The DY365 4CE remote actuator is a four-relay electronic device that receives the command signals
from the switch via DY365 I/O extension ports.
It performs actions of 1B type and is intended to operate in a domestic and similar environment
with overvoltage category III and normal pollution degree (EN 60730-1).
SAFETY WARNINGS
During product installation and operation it is necessary to observe the following
instructions:
1) The device must be installed by a qualified person
2) Before accessing the terminals, make sure that the leads are not live
3) Do not power the device if any part of it is damaged
4) Connect the product following the diagrams described in this manual
5) In the electrical system upstream of the device must be installed a switch and a
protection device against the overcurrents.
6) The product must be installed and activated in compliance with current electric
systems standards.
7) After installation inaccessibility to the terminals without using dedicated tools
must be guaranteed.
Code Model Description
2CSM221181R1000 DY365 4CE 4-channel remote actuator
TECHNICAL FEATURES
• Power supply: 12/24 V AC/DC (-15%/+10%) 50/60 Hz
• 4 relays normally open 8A / 250 V AC
• I/O extension port for connection to the switchDY365
• Operating temperature: 0 ÷ +50 °C
• Storage temperature: -25 ÷ +70 °C
• Container: 4 DIN modules
• Protection degree: IP20 (IP40 when correctly installed in the electrical panel)
OPERATION
• When switched on, the red LEDs emit 2 flashes lasting half a second (switch-on sequence).
• Once the switch-on sequence is completed, the green LED is lit to indicate normal device
operation and the red LEDs are turned on/off to indicate the corresponding status of the
4 channels (on = ON).
Channels configuration
• During normal operation, press and hold the SET button for at least 3 seconds to enter
in configuration mode. In this mode the green LED is off while the red LED
corresponding to the relay to be configured flashes.
• To select the relay to be associated with the channel of DY365 switch , press the SET
button until the red LED for the relay to be configured flashes.
• Once the channel is selected, the actuator remains in configuration mode for 60 seconds:
activate the channel configuration on the DY365 switch.
To activate the channel configuration, see the DY365 switch user manual.
• Once the relay configuration is complete, the actuator resumes normal operation
• To cancel the configuration of a channel, enter the configuration mode, select the channel
with the SET button (relative red LED flashing), then press the SET button for at least three
seconds until the green LED lights up again.
Each new configuration cancels the previous configuration
REFERENCE STANDARDS
Compliance with Community Directives:
2014/35/EU (LVD)
2014/30/EU (EMCD)
is declared in reference to the harmonized Standards:
EN 60730-1
EN 301 489-1/3 and EN 300 220-3
Description
Connection diagram
8 A / 250 V ~
5
0
-
6
0
H
z
8 A / 250 V ~ 8 A / 250 V ~ 8 A / 250 V ~
Out 1
Out 2 Out 3 Out 4
2
3
0
V
~
I/O extension port
(B) (A)
Green LED for operating status signaling
Red LEDS for relay status signaling
SET BUTTON for channels programming and resetting
Dimensions (mm)
87 mm
72 mm
45 mm
60 mm
65 mm
DY365 4CE
2CSM441048D0201
ABB S.p.A
V.le dell’Industria 18
20010 Vittuone (MI) - Italy
Tel. +39 02 2415 0000
https://new.abb.com/low-voltage
© Copyright 2019 ABB S.P.A . All rights reserved.
We reserve the right to make technical changes or modify
the contents of this document without prior notice.
Installation Manual

Product specificaties

Merk: ABB
Categorie: Niet gecategoriseerd
Model: DY365 4CE

Heb je hulp nodig?

Als je hulp nodig hebt met ABB DY365 4CE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd ABB

ABB

ABB US/U 12.2 Handleiding

27 Mei 2023
ABB

ABB DWTL1 Handleiding

26 Mei 2023
ABB

ABB D1 Plus 110 Handleiding

12 Mei 2023
ABB

ABB D1 Plus 24 Handleiding

7 Mei 2023
ABB

ABB D2 Plus Handleiding

23 April 2023
ABB

ABB System Pro M DT1 Handleiding

20 April 2023
ABB

ABB VAA/S6.230.2.1 Handleiding

19 April 2023
ABB

ABB AD1-R-15m-72 Handleiding

18 April 2023
ABB

ABB System Pro M DT2-K Handleiding

17 April 2023
ABB

ABB SA/S8.16.2.1 Handleiding

16 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024