ABB DY GPS Handleiding

ABB Niet gecategoriseerd DY GPS

Lees hieronder de 📖 handleiding in het Nederlandse voor ABB DY GPS (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 250 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

REFERENCE STANDARDS

Compliance with Community Directives:

2014/30/EU (EMCD)

2014/53/EU (RED)

is declared with reference to the following harmonized standards:

• EN 60950-1

• ETSI EN 301 489-1, ETSI EN 301 489-3, ETSI EN 300 440-1, ETSI EN 300 440-2

1User Manual

GPS MODULE FOR EXTERNAL USE

 Read all the instructions carefully

DIMENSIONS (mm)

DEVICE STATUS

INSTALLATION

DY GPS

is a GPS module that allows you to capture the information of

date, time and position from satellites. This information may be shared

with DY365 device designed to interface with

DY GPS

, so as to ensure a

synchronization always perfect.

Code Model Description

2CSM250411R1000 DY GPS GPS module for external use

SAFETY WARNINGS

During product installation and operation it is necessary to observe the

following instructions:

1) The product must be installed by a qualified person, in strict compliance

with the connection diagrams.

2) Do not power the instrument if any part of it is damaged.

3) The product must be installed and activated in compliance with current

electric system standards.

4) The electrical system in the building in which the product is to be installed

should have an over-current switch and a protection device.

5) Do not use the product for purposes different from the one specified.

6) In case of malfunction do not perform repairs and contact immediately the

technical support.

7) The product can be used in environments with category of overvoltage III

and pollution degree 2.

8) Before accessing the connection terminals, verify that the leads are not live.

9) After installation, inaccessibility to the connection terminals without

appropriate tools must be guaranteed.

TECHNICAL CHARACTERISTICS

• Power supply: 12V DC (-20% ÷ +20%)

• Absorption: 30mA max (during receiving GPS)

• Wall or pole installation

• Wiring

– Cable length: 100m

– Flexible cables section: 0.75 ÷ 1.5 mm

– Sheathed cables maximum diameter: 3 mm

• Protection degree: IP54

• Operating temperature: 0 ÷ +50 °C

• Storage temperature: -25 ÷ +70 °C

• Operating humidity: 20÷90% non condensing

• Key to force sending data to the connected devices

• Red / green / orange led for signaling device status (Figure 1)

Led for signaling

device status

Key to force sending data

to the devices

• Installation can be wall or pole (by using the adapter in the package)

• Remove the cover by leveraging the teeth on the sides of the product

• Pass the cables through the cable entry on the bottom side and connect the

power and bus cables respecting the wiring diagram

• Tighten the cable gland and replace the cover.

• When you power on the led emits two red flashes as follows:

OFF ON OFF ON OFF

… 1 s 1 s 1 s …

After the power on sequence, the DY GPS:

- acquires data of time, date, latitude, longitude and number of satellites received

about every 30 seconds

- sends data of time, date, latitude, longitude to the I/O extension port (and to the

connected devices) every 30 minutes

The flashing of the green led indicates the number of the received satellites

(the higher the number of satellites received, the better the reception of the

information):

Number of satellites Green led sequence

ON OFF REPETITIONS

0 - 2 500 ms 500 ms continuous

3 – 5 100 ms 300 ms 3 every 5 seconds

6 – 8 100 ms 300 ms 6 every 5 seconds

9 – 12 100 ms 300 ms 9 every 5 seconds

• Sending data to the I/O extension port (and to the connected devices) is signaled

by the red flashing of the led for 3 seconds as follows:

ON OFF ON OFF …..

100 ms 100 ms 100 ms 100 ms …..

Note: at any time you can force sending data to the I/O extension port by pressing

the key (accessible by removing the cover, see figure 2).

• Failure to receive the correct data for more than 60 seconds causes an auto-reset

of the device. After three fruitless recovery attempts, this condition is signaled by

the red flashing of the led as follows:

ON OFF ON OFF …..

500 ms 500 ms 500 ms 500 ms …..

In this case, the DY GPS tries to restore the operation of the GPS module by

continuing signaling; in case it succeeds, it will return to normal operation (flashing

of the led of green colour according to the number of the detected satellites).

• Failure to receive the correct data for more than 30 minutes causes an auto-

reset of the device with loading of factory settings and subsequent restart. This

condition is signaled by the orange flashing of the led for 3 seconds as follows:

ON OFF ON OFF …..

300 ms 300 ms 300 ms 300 ms …..

3CONNECTION DIAGRAMS

I/O extension

port

Figure 1 Figure 2

DY GPS

2CSM441046D0201

ABB S.p.A

V.le dell’Industria 18

20010 Vittuone (MI) - Italy

Tel. +39 02 2415 0000

https://new.abb.com/low-voltage

We reserve the right to make technical changes or modify

the contents of this document without prior notice.

Installation Manual

Product specificaties

Merk:	ABB
Categorie:	Niet gecategoriseerd
Model:	DY GPS

Heb je hulp nodig?

Als je hulp nodig hebt met ABB DY GPS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd ABB

ABB US/U 12.2 Handleiding

27 Mei 2023

ABB DWTL1 Handleiding

26 Mei 2023

ABB D1 Plus 110 Handleiding

12 Mei 2023

ABB D1 Plus 24 Handleiding

7 Mei 2023

ABB D2 Plus Handleiding

23 April 2023

ABB System Pro M DT1 Handleiding

20 April 2023

ABB VAA/S6.230.2.1 Handleiding

19 April 2023

ABB AD1-R-15m-72 Handleiding

18 April 2023

ABB System Pro M DT2-K Handleiding

17 April 2023

ABB SA/S8.16.2.1 Handleiding

16 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Smeg GTA-6 Handleiding

21 November 2024

Smeg KIT6CX Handleiding

21 November 2024

Senal SCS-98 Handleiding

21 November 2024

Senal ASM-6 Handleiding

21 November 2024

Senal ASM-MNTKIT Handleiding

21 November 2024

Senal SMS-45 Handleiding

21 November 2024

Smeg KIT6PX Handleiding

21 November 2024

Senal SCI-3212MP Handleiding

21 November 2024

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024

Senal OLM-2S-P Handleiding

21 November 2024