4ms Stereo Triggered Sampler Handleiding

4ms Niet gecategoriseerd Stereo Triggered Sampler

Lees hieronder de 📖 handleiding in het Nederlandse voor 4ms Stereo Triggered Sampler (24 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
Stereo Triggered Sampler
4ms Company
User Manual 1.0 – August 16, 2017
for f irmware v1.0
The Stereo Triggered Sampler is a high fidelity, two-channel stereo audio recorder and playback module. The
STS can record high quality stereo WAV files while simultaneously playing two different stereo files. A maximum of
600 samples can be loaded at one time from the removable/swappable microSD card, in a variety of formats up to
96kHz/32-bit/stereo WAV. All sample parameters (1V/oct pitch, sample file selection, length, and start position) are
CV controllable, and trigger jacks for play, record, and reverse allow for synchronization. On-board editing tools
allow you to set loop/trim points and gain, as well as assigning samples to banks and slots.
Two independent stereo playback channels can play any of 600 samples simultaneously
Recording channel creates stereo WAV files directly onto microSD Card for immediate use
Extremely low noise, high fidelity design
Plays a variety of WAV files up to 32-bit/96kHz
Intelligent file system makes loading large sample libraries easy by organizing banks into folders
CV and controls for 1V/oct tracking, Start Position, Length, Sample selection, Reverse and Play
Trim samples and set Loop points, adjust gain, and re-organize banks and sample slots on the fly.
Includes microSD card with Sample Pack, SD adaptor, 10-to-16 pin power cable and M3 screws
Table of Contents
Setting up your Stereo Triggered Sampler
1. Remove the Stereo Triggered Sampler (STS) from the box and anti-static bag. The RAM chip on the STS may
be damaged by static electricity; take care not to touch the circuit board.
2. Connect the free end of the power cable to a 16-pin Eurorack power header on your power supply distribution
system, with the red stripe towards to the -12V. The other end of the power cable is a
10-pin connector which should already be connected to the STS so the red stripe on
the power cable is orientated towards the bottom of the module (the bottom is marked
by a white stripe and the word “POWER”). Note: The STS is reverse-polarity
protected, but other modules being incorrectly connected could damage anything on
the power bus.
3. Backup your microSD card before you first power the STS on! We recommend
you perform a full backup of the microSD card by using a computer (use the included
SD card adaptor if needed). This will be useful if the card ever becomes damaged or
you wish to restore the STS to the original factory settings and samples.
4. Securely screw the STS to the rails of your case. Power the system on.
5. Begin with Tutorial 1: Basic Playback on page 5 of this manual.
Never remove the microSD card when the light is on!Busy !
Setting up your Stereo Triggered Sampler 2! ".............................................................
Overview 3! "................................................................................................................
Electrical and Mechanical Specifications 4! "..............................................................
Tutorial 1: Basic Playback 5! "......................................................................................
Tutorial 2: Navigating Banks 6! "..................................................................................
Stereo/Mono Mode 8! "................................................................................................
Channel Playback Volume 8! ".....................................................................................
Tutorial 3: Recording Samples 9! "...............................................................................
Tutorial 4: Loading Files onto the microSD Card 10! ".................................................
Sample List HTML file 12! "..........................................................................................
Edit Mode: Gain, Loop/Trim points 13! "......................................................................
Saving and Reverting 14! "...........................................................................................
Copying 14! "................................................................................................................
Tutorial 5: Creating Slices 15! "....................................................................................
Example Patch: Sequencing the STS 16! "..................................................................
Example Patch: Granular Scrubbing 17! "...................................................................
Recording the STS Output as a New Sample 18! ".....................................................
Example Patch: Clock Sync and Shifting Ping-Pong Loops 18! "...............................
Assigning Samples to Banks and Slots 19! "...............................................................
System Mode 21! ".......................................................................................................
1V/OCT Tracking Compensation 21! ".........................................................................
Rebuilding the Index File 21! ".....................................................................................
Updating Firmware (Audio Bootloader) 22! "...............................................................
microSD Card Specifications 23! "...............................................................................
File Formats 23! ".........................................................................................................
Chart of All Button Features 24................................................................................!
Page of  2 24
Overview
Up to 600 samples loaded at one time (10 samples per bank)
Includes a microSD card with over 200 samples
Extremely quiet, low noise and low jitter design
Stereo or Mono operation:
Stereo mode: Two stereo files are mixed and played through the L and R output jacks (L+L and R+R)
Mono mode: Each file is mixed to mono and output through the channel's output jack (L+R and L+R)
Firmware can be updated by playing an audio file into the STS
Two independent playback channels:
Each channel outputs in mono or stereo through the shared L/R jacks
Play button/trigger jack: Tapping the button or receiving a trigger starts/re-starts the sample
When Length is set to “All”, the Play button starts/stops the sample (set in System Mode, see p.21)
Sample CV/knob: select which sample within the channel's bank
1V/OCT CV and Pitch knob: playback pitch (-10 to +4.3 octave range)
Start Pos CV/knob: position in the sample to begin playback (loop start point)
Length CV/knob: playback time (loop end point)
Length knob at max: entire file is played
Length knob 50%-99%: 200ms - 5s of the sample is played (beginning at the Start Position)
Length knob <50%: Percussive decay envelope is applied to the playback (attack-only envelope if
playing Reverse)
Length <1%: Tiny grains are played (can be used to sweep through sample file data manually)
Reverse button/jack: toggles forward/backwards
Bank button: selects channel's bank
and turn the knobs for fast selection of bank Tip: Hold Bank Sample
Edit button allows basic on-board editing features:
Set loop/trim points with Scrub Start and Scrub End
Set (boost/cut from 10% to 500%) Gain
Re-organize samples with Next File
Move samples around within a bank
Assign files from any folder on the microSD card into any sample slot (sub-folders are ignored)
Copy sample to multiple slots, each with their own loop/trim/gain settings
Reverse+Start Pos button/knob combo allows for setting volume of each channel independently.
Maximum file size for playback: 4GB per file (6.7 hours per file at 44.1kHz/16b/stereo)
microSD Card is hot-swappable when light is off: no power-down required to change cards Busy
Samples that are pre-loaded into memory can continue playing while card is removed
Recording channel:
Stereo recording can be simultaneous to operation of playback channels
Easily record output of sample playback, “bouncing” a play session into a new sample file
Recording initiated by button or trigger
Monitor mode lets you check the signal before starting a recording
Record into any sample slot in any bank
Every recording is saved as a WAV file on the microSD Card and can be played back instantly
Edit features allow you to manually browse all the takes, and assign them to banks/sample slots
Recording can be disarmed to prevent accidental recordings
44.1kHz/24-bit stereo or 16-bit stereo recording, selectable in System Mode
“Unlimited” recording time (records continuously until card is full)
256GB card = 18 days of continuous recording (432.9 hours)
Long recordings are split into 4GB WAV files
Page of  3 24


Product specificaties

Merk: 4ms
Categorie: Niet gecategoriseerd
Model: Stereo Triggered Sampler

Heb je hulp nodig?

Als je hulp nodig hebt met 4ms Stereo Triggered Sampler stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd 4ms

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd