3D Systems CubePro Handleiding

3D Systems 3D Printer CubePro

Lees hieronder de 📖 handleiding in het Nederlandse voor 3D Systems CubePro (86 pagina's) in de categorie 3D Printer. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/86

CubePro™

User Guide

Original Instructions

Prosumer 3D Printer

3D Systems, Inc.

TABLE OF CONTENTS

1 INTRODUCTION ........................................................................................1

FCC Notice .........................................................................................1

KCC ...............................................................................................1

COMPLIANCE ......................................................................................1

Warranty ...........................................................................................2

Limitation of Liability ................................................................................2

2 IMPORTANT SAFETY INFORMATION 3 .......................................................................

Safety Symbols and Definitions ........................................................................3

Safety Guidelines ...................................................................................3

3 CUBEPRO 3D PRINTER FEATURES AND BENEFITS 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CubePro 3D Printer Properties ........................................................................4

Print Materials ......................................................................................4

Material Color Choices ...............................................................................4

4 AT A GLANCE ..........................................................................................5

5 SPECIFICATIONS AND REQUIREMENTS ....................................................................7

Dimensions and Weight ..............................................................................7

Weight and Dimensions ..............................................................................7

PC Requirements ...................................................................................7

Software ...........................................................................................7

Electrical Requirements ..............................................................................7

Material Storage ....................................................................................7

6 UNPACKING AND SETTING UP YOUR CUBEPRO ............................................................8

Contents ...........................................................................................8

Unpacking and Setting Up Your CubePro 9 ................................................................

Setup and Activate Your CubePro .....................................................................14

Touchscreen Display ...............................................................................20

Installing a Material Cartridge ........................................................................22

7 PRINTING YOUR CREATION 25 .............................................................................

Printing Procedure .................................................................................25

8 FINISHING YOUR CREATION ............................................................................29

Removing Your Creation From The Print Pad 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing Rafts ...................................................................................29

Removing Supports ................................................................................29

Removing Supports - Optional Ultrasonic Support Removal Tank 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hot Water Method .................................................................................30

Caustic Soda Method ..............................................................................31

9 CUBEPRO SOFTWARE 33 .................................................................................

Installing Windows Software .........................................................................33

Installing Mac Software .............................................................................34

CubePro Software Overview .........................................................................35

Home Tab .........................................................................................35

3D Systems, Inc.

CAD File Functions ................................................................................36

Geometry Functions ...............................................................................36

Color, Build, Print File and Help .......................................................................37

View Tab ..........................................................................................37

Zoom and View ...................................................................................37

Print Paths .......................................................................................38

Settings Tab 38 .......................................................................................

Printer Configuration ...............................................................................39

Build Settings .....................................................................................40

Descriptions ......................................................................................41

Firmware Update ..................................................................................45

Printer Connection .................................................................................45

Preparing and Printing a Creation .....................................................................46

10 OPERATION PROCEDURES .............................................................................49

Applying Cube Glue 49 ................................................................................

Layer 1 ..........................................................................................49

Layer 2 ..........................................................................................49

Replacing a Material Cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Setting Up an ad Hoc Network ........................................................................54

11 CUBEPRO MAINTENANCE ..............................................................................56

Restoring Roughness to the Print Pad .................................................................56

Cleaning the Jet Wiper ..............................................................................56

General Cleaning ...................................................................................57

Adjusting the Jet Wiper Assembly ....................................................................57

Calibrating the Print Pad ............................................................................59

Calibrating the Z-Gap And Print Pad Level ..............................................................61

Level Gap Calibration Print Overview ..................................................................61

Printing the Level Gap Calibration File .................................................................62

Adjustment Knob Measurement ......................................................................63

Reading the Print Pad Level Calibration Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Reading The Z-Gap Calibration Print ..................................................................64

Calibrating the Offset Jets ...........................................................................66

Calibration Overview ...............................................................................66

Reading the Offset Jets Scale ........................................................................67

Offset Jets Calibration Procedure .....................................................................68

Calibrating the Wipe Function ........................................................................71

Testing the Print Jets and Extruders 71 ...................................................................

Moving the Print Jets 73 ...............................................................................

Updating the CubePro Firmware ......................................................................74

Updating Firmware Using USB .......................................................................74

Updating Firmware Using WI-FI ......................................................................75

Replacing Fuses ...................................................................................78

Lubricating The Bearing Rods ........................................................................79

Error Codes .......................................................................................80

Material Flow Errors ................................................................................80

Temperature Errors ................................................................................80

Contacting Support .................................................................................80

Product specificaties

Merk:	3D Systems
Categorie:	3D Printer
Model:	CubePro
Kleur van het product:	Black, White
Ingebouwd display:	Ja
Gewicht:	41000 g
Breedte:	566 mm
Diepte:	581 mm
Hoogte:	606 mm
Stroom:	6 A
Touchscreen:	Ja
USB-poort:	Ja
Nauwkeurigheid:	1 procent
Kijkglas:	Ja
Ondersteunt Mac-besturingssysteem:	Mac OS X 10.9 Mavericks
Printtechnologie:	Plastic Jet Printing (PJP)
Wifi:	Ja
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
RAM minimum:	2 GB
Minimum display resolutie vereiste:	1024 x 768 Pixels
Printmateriaal:	ABS, Polylactic acid (PLA)
Maximaal afdrukformaat:	- mm
Laagdikte (min):	0.07 mm
Laagdikte (max):	0.3 mm
Aantal printkoppen:	3
Ondersteunde laagdikte:	0.2, 0.3 mm
Maximale extrudertiptemperatuur:	280 °C
Minimale processorsnelheid:	2 GHz
Verticale printsnelheid (max):	54000 mm/u
Aantal afdrukkleuren:	3