Zodiac Cadet 240 Roll Up Boot Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Zodiac Cadet 240 Roll Up Boot (10 pagina's) in de categorie Boten. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/10
/ 10
E
N
G
L
I
S
H
1
CAUTION
z
z
z
zz CAREFULLY READ THIS MANUAL BEFORE OPERATING YOUR
BOAT.
z
z
z
zz THIS OWNER’S MANUAL IS IN TWO VOLUMES THAT MUST BE
KEPT TOGETHER.
NOTICE:
THE OWNER'S MANUAL IS IN TWO VOLUMES:
- VOLUME 1
DEALS WITH OPERATING PRECAUTIONS AND SAFETY
RECOMMENDATIONS THAT MUST BE OBSERVED.
- VOLUME 2
DEALS WITH TECHNICAL SPECIFICATIONS AND ASSEMBLY
PROCEDURE OF THE BOAT AND ITS EQUIPMENT.
VOLUME 2
TECHNICAL SPECIFICATIONS - ASSEMBLY PROCEDURE
ZODIAC
CADETS
CADET ROLL UP 200 - 240 - 260
CADET SOLID 260 – 285 – 310 – 340
CONTENTS
Page Page
Ö
Ö
Ö
ÖÖInflation 7
Ö
Ö
Ö
ÖÖ Ö
Ö
Ö
ÖÖAssembly procedure 2 Pressure 8
Ö
Ö
Ö
ÖÖ Ö
Ö
Ö
ÖÖCheck on unpacking 2 Assembly of equipment 9
Ö
Ö
Ö
ÖÖ Ö
Ö
Ö
ÖÖAssembly 3 - 5 Deflation - folding the boat 10
Ö
Ö
Ö
ÖÖ Ö
Ö
Ö
ÖÖInflation system 6 General description I - IV
/ 10
2
ASSEMBLY PROCEDURE
We recommend that you follow the specific order of the assembly procedure. Proceed step by step
and refer to the corresponding pages.
PROCEDURE PAGE SECTION
1. inventory the elements composing your boat, 2 CHECK ON UNPACKING
and learn how to recognise them I - IV DESCRIPTION
2. activate valves in inflating position 6 INFLATION SYSTEM
3. slightly inflate the main buoyancy tube 7 INFLATION
4. CADET RU 200 - RU 240 : Insert the wooden slats in
their pockets
CADET RU 260 : install the rolling floor
CADET SOLID : assemble the floorboard
3 - 5 ASSEMBLY
5. Install the seat (except CADET RU 200) 9 ASSEMBLY OF
EQUIPMENT
6. finish inflation of the boat to the correct pressure 7 - 8 INFLATION / PRESSURE
7. Install the oars 9 ASSEMBLY OF
EQUIPMENT
CHECK ON UNPACKING
CAUTION
DO NOT USE A SHARP TOOL
The pack must contain: 1 buoyancy tube +
Cadet Roll up
Cadet Solid
C200RU C240RU C260RU
C260S
C285S
C310S
C340S
Floorboard S (1) S (1) R (1) PF (1) PF (1) PF (1) PF (1)
inflatable keel 1 1 1 1
Stringer 2 2 2 2
Repair kit 1 1 1 1 1 1 1
Owner’s manual (2) 1 1 1 1 1 1 1
Equipement standard
Removable wooden seat 1 1 1 1 1 1
Carry bag 1 1 1 1 1 1 1
Reinforced aluminium oar 2 2 2 2 2 2 2
Foot-pump 1 1 1 1 1 1 1
(1) S = Slats R = Rolling floor PF = Marine Plywood Floor
(2) 2 volumes
You can equip your boat with many optional accessories (transportation wheels, boarding ladder,
lifting rings etc.). Ask your dealer to advise you.
NOTICE : IF YOU WISH TO ADD LIFTING RINGS, YOU MUST FIX THEM ON THE
BUOYANCY TUBE, NEVER ON THE FLOOR
/ 10
E
N
G
L
I
S
H
3
ASSEMBLY
Choose a smooth and clean surface
IF THE BUOYANCY TUBE WAS STORED AT A TEMPERATURE BELOW
0°C / 32°F, LEAVE IT AT 20°C / 68°F FOR 12 HOURS BEFORE
UNFOLDING.
CADET SOLID : INSTALL THE MARINE PLYWOOD FLOOR:
• Sprinkle some starch in the angle (joint of the buoyancy tubes to the bottom) to facilitate fitting.
CAUTION, NEVER USE TALCUM POWDER.
• Make sure you identify the parts and direction in which they fit:
- The floorboard consists of 3 main sections and 2 sections in the bow [fig 1 and 4]
- The bow sections have an upside and a downside.
1. Insert the bow section (1) into the bow angle.
2. Insert the rear section (5) against the transom (6) as show on fig 1.
3. Fit all sections together [fig.1].
4. Position sections 3 and 4 as an apex (in a tent-like position) [fig 1 and 2].
5. Check that all sections are correctly aligned [fig 4].
6. Check that the floorboard is correctly fitted in the angles.
7. Flatten the apex by standing on it (in the boat) and pulling the lifelines to prevent the fabric being
pinched [fig. 2].
8. Assemble the stringers (see instructions bellow).
CADET SOLID : ASSEMBLY OF THE STRINGERS
The stringers are essential to good working of the boat: they lock the floorboard together and stiffen its
structure.
1. To facilitate the fitting of the first stringer, slide the other stringer under the boat, about 20 cm from
the side [fig. 3-a].
DO NOT PUT THE STRINGER IN POSITION UNDER THE BOAT UNTIL
THE FLOOR IS FLATTENED.
2. Position the stringer on the edge of the floorboard. The reference mark on the stringer (8) must
remain on top (the thicker part should be towards the top) [fig. 3].
3. Fit the stringers between the two buffers (9) of sections 3 and 5 [fig. 4].
4. Rotate the stringer in the angle so as to press them against the bottom [fig. 3-b and 4].
5. Because of the self-locking system of the floorboard, the stingers will fit into place once the
buoyancy tube is inflated.
Product specificaties
| Merk: | Zodiac |
| Categorie: | Boten |
| Model: | Cadet 240 Roll Up Boot |
Heb je hulp nodig?
Als je hulp nodig hebt met Zodiac Cadet 240 Roll Up Boot stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Boten Zodiac
3 Oktober 2022
Handleiding Boten
Nieuwste handleidingen voor Boten
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022