ZKTeco ZKP8008 Handleiding

ZKTeco Printer ZKP8008

Lees hieronder de 📖 handleiding in het Nederlandse voor ZKTeco ZKP8008 (40 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/40

POS rinter-80- PSeries

Programmer Manual

[Name] Horizontal tab

[Format] ASCII HT

Hex 09

Decimal 9

[Description] Moves the print position to the next horizontal tab position.

[Details] • This command is ignored unless the next horizontal tab position has been set.

• If the next horizontal tab position exceeds the printing area, the printer sets the

printing position to [Printing area width + 1].

• Horizontal tab positions are set with ESC D.

• If this command is received when the printing position is at [printing area

width+ 1], the printer executes print buffer-full printing of the current line and

horizontal tab processing from the beginning of the next line.

• The default setting of the horizontal tab position for the paper roll is font A(12

×24) every 8th character (9th, 17th, 25th, ... column).

[Reference] ESC D

[Name] Print and line feed

[Format] ASCII LF

Hex 0A

Decimal 10

[Description] Prints the data in the print buffer and feeds one line based on the current line

spacing.

[Note] This command sets the print position to the beginning of the line.

[Reference] ESC 2, ESC 3

[Name] Print and carriage return

processed as the code for ESC 3 <10>H.

 Even though the printer is not selected using ESC = (select peripheral

device), this command is effective.

 The printer transmits the current status. Each status is represented by

onebyte data.

The printer transmits the status without confirming whether the host

computer can receive data.

The printer executes this command upon receiving it.

This command is executed even when the printer is off line, the receive -

buffer is full, or there is an error status with a serial interface model.

With a parallel interface model, this command can not be executed when

the printer is busy. This command is executed even when the printer is off-line

or there is an error status when DIP switch 2 1 is on with a parallel interface-

model.

When Auto Status Back (ASB) is enabled using the GS a command, the

status transmitted by the DLE EOT command and the ASB status must be

differentiated.

n = 1: Printer status

Bit / OFF ON HEX Decimal

Function

0 OFF 00 0

Not used.Fixed to Off.

1 ON 02 2 Not used.Fixed to On.

2 OFF 00 0 Drawer open/close signal is LOW(connector pin3).

ON 04 4 Drawer open/close signal is LOW(connector pin3).

3 -- -- -- Undefined.

4 ON 10 16 Not used.Fixed to On.

5.6 -- -- -- Undefined.

7 OFF 00 0 Not used.Fixed to Off.

n = 2: Off line status-

Bit Off/On Hex Decimal Function

0 0 0 00 Not used Fixed to Off.

Product specificaties

Merk:	ZKTeco
Categorie:	Printer
Model:	ZKP8008
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Soort:	POS-printer
Kleur:	Nee
USB-poort:	Ja
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Type stroombron:	DC
Aantal USB 2.0-poorten:	1
Intern geheugen:	- MB
Maximum roll diameter:	83 mm
USB-connector:	USB Type-B
Printtechnologie:	Direct thermisch
Ingebouwde streepjescodes:	1D
Printsnelheid (metrisch):	260 mm/sec
Wifi:	Nee
Ondersteunde papierwijdte:	0.06 - 0.08 mm
Character sets:	ASCII