Yamaha YWA-10 Handleiding

Yamaha Draadloos audio systeem YWA-10

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha YWA-10 (2 pagina's) in de categorie Draadloos audio systeem. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

YWA-10

Wireless Network Adapter

Owner’s Manual

English

YWA-10/EN-1

Allows Yamaha AV products equipped with a

NETWORK port and a DC OUT jack to be connected

with a wireless LAN.

Compatible devices can connect to the YWA-10

through a USB connector instead of a DC OUT jack.

Refer to the website below for a list of compatible

devices.

http://yamaha.com/

The firmware of this unit may be updated at times for

improvement. Please refer to the following website for

information on firmware updates.

http://yamaha.com/

Features

AV Receiver

YWA-10

Internet

connection

Modem

Wireless LAN router

(base unit)

Setup procedure

Checking the base unit

• Check that the Wireless LAN router (base unit)

can connect to the Internet.

Connecting to the base unit

• When the Wireless LAN router (base unit) has a

WPS button

^Carry out the procedures in “Step 2-A

Connecting to the base unit (using WPS)” to

connect to the base unit.

• When the Wireless LAN router (base unit) does

not have a WPS button

^Carry out the procedures in “Step 2-B

Connecting to the base unit (manual

configuration)” to connect to the base unit.

✻If connecting using “(using WPS)” does not

succeed, refer to “(manual configuration)” and

configure the connection.

Connecting to an AV product

The Wi-Fi CERTIFIED Logo is a

certification mark of the Wi-Fi

Alliance.

The Wi-Fi Protected Setup Mark

is a mark of the Wi-Fi Alliance.

aPOWER indicator

bWPS indicator

cWIRELESS indicator

dPower connector

eLAN1 port, LAN2 port

fWPS button

gReset button

• If you do not already have an Internet connection, please apply for one

before setting up this unit.

• Do not connect the USB power cable to a USB hub.

Part names

Things to check before setup

a b

d e f

Upper surface of product Rear

Side

aCheck that the wireless LAN router (base unit) can connect to the

Internet without difficulty.

Notes

• If you do not currently have an Internet subscription, please obtain one.

• A wireless LAN router is required to set up a connection using this

procedure. Please obtain a wireless LAN router if you do not have one

available.

bCheck whether the wireless LAN router (base unit) is WPS compatible.

Check the owner's manual and other documentation supplied with the

wireless LAN router.

Note

WPS (Wi-Fi Protected Setup) is a function that uses a button to configure

connections and security on wireless LAN devices.

*Some Wi-Fi devices have “WPS” written on them.

Step 1 Checking the base unit

WWhen the wireless LAN router (base unit) has a WPS button

Carry out “Step 2-A Connecting to the base unit (using WPS)”, and then

“Step 3 Connecting to an AV product”, in that order.

WWhen the wireless LAN router (base unit) does not have a WPS

button

Carry out “Step 2-B Connecting to the base unit (manual configuration)”,

and then “Step 3 Connecting to an AV product”, in that order.

Computer

Internet connectivity

Wireless LAN

router

(base unit)

Modem

Internet

connection

Notes

• This explanation details the procedure for connecting using the WPS

function. When using a base unit that is not equipped with a WPS

function, refer to “Step 2-B Connecting to the base unit (manual

configuration)” at right.

• You will need to change the IP address of this unit if you are using more

than one YWA-10 at the same time.

Refer to “Troubleshooting” on the reverse page for more details.

1. Supply power to the YWA-10

aTurn on the power of the AV product that you wish to connect this unit

to.

bUse the supplied USB power cable to connect the power connector on

this unit to the DC OUT jack on the AV product.

The indicator on the front panel of this unit lights. Wait for approximately one

minute after the indicator lights and then carry out the following procedure.

Note

If the AV product is not equipped with a DC OUT jack, connect to the USB

connector on the front panel.

2. Connect the base unit

aPress the WPS button on the wireless LAN router (base unit).

Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to use the WPS button.

bPress and hold the WPS button on the rear of this unit for more than 5

seconds and release it.

The WPS indicator on the front panel lights.

cWait until the WPS indicator turns off (this will take two minutes at

most).

Note

If the WPS indicator blinks, carry out procedure 2 again, starting at number

Step 2-A Connecting to the base unit

(using WPS)

This completes connection with the base unit. Proceed to “Step 3

Connecting to an AV product”.

AV Receiver

Rear Panel

Press and hold for more

than 5 seconds.

Notes

• When making a manual connection to the base unit, or when you are

unable to connect using the procedure described in “Step 2-A Connecting

to the base unit (using WPS)” at left, refer to the explanation below.

• If the PC you are using to configure this unit is connected to the wireless

LAN, turn the PC’s wireless LAN function off.

• You will need to change the IP address of this unit if you are using more

than one YWA-10 at the same time.

Refer to “Troubleshooting” on the reverse page for more details.

1. Check the network that you are attempting to

connect to.

You will need the setting information from the wireless LAN router (base unit)

when connecting or setting up this unit. Have the following table ready for use.

* Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to check its wireless LAN settings.

■When using WEP security settings

*1: 16-digit number (0–9, A–F), *2: ASCII (0–9, A–Z, a–z)

■When using WPA/WPA2 security settings

Note

Use only alpha-numeric characters (0–9, A–Z, a–z) for an SSID or password.

Otherwise, Yamaha cannot guarantee normal operation.

Refer to the owner’s manual of the wireless LAN router (base unit) for

information on how to change the SSID or password.

2. Connect this unit to a PC

aTurn the PC power on.

bUse the supplied LAN cable to connect the LAN1 port (or the LAN2 port)

on this unit to the LAN port on the PC. Then, use the supplied USB

power cable to connect the power connector on this unit to the USB

connector on the PC.

The indicator on the front panel of this unit lights. Wait for approximately one

minute after the indicator lights and then carry out the following procedure.

3. Setting up this unit

aStart the web browser on the PC.

bEnter “ywa.setup” in the

address field in the Web

browser, and press the Enter

key.

Note

If the login screen does not appear even after you enter “ywa.setup”, enter

“192.168.1.249” and press the Enter key. If the login screen still does not

appear, refer to “Troubleshooting”.

Step 2-B Connecting to the base unit

(manual configuration)

Name Wireless LAN setting

(1) SSID

(2) Security mode ❑ Open ❑ Shared

(3) Security key type ❑ Hexadecimal*1 ❑ ASCII*2

(4) Default key ❑ Key 1 ❑ Key 2 ❑ Key 3 ❑ Key 4

(5) Password

Name Wireless LAN setting

(1) SSID

(2) Security mode ❑ WPA-PSK ❑ WPA2-PSK

(3) Encryption type ❑ TKIP ❑ AES

(4) Password

To assure the finest performance, please read this

manual carefully.

Keep it in a safe place for future reference.

Check that the following accessories are supplied with

the product.

Owner’s Manual (this manual)

Package contents

Wireless Network

Adapter (this unit)

LAN cable

USB power cable

Continues to the back side.

YWA-10_dtp_En.fm Page 1 Thursday, April 12, 2012 12:07 AM

cOn the login screen, enter

“admin” in the user name field,

and “password” in the

password field, and then click

the OK button.

Note

If you cannot login to the setup screen, check that you have entered the

correct letters.

dWhere necessary, select the display language from the drop-down list.

The screen display language changes.

Note

The display examples in this manual use English as the display language.

eClick [Setup Wizard] and then [Next], in that order.

The “Wireless Site Survey” screen appears.

fOn the “Wireless Site Survey” screen, choose the same SSID as in (1)

on the table in “1 Check the network that you are attempting to connect

to.” and then click [Next].

Notes

• When the SSID does not appear, click [Refresh] and then search again.

• If the SSID (the name of the device you are connecting to) does not

display even when the above operation is performed, the wireless LAN

router (base unit) power is turned off, or the SSID name notification is

turned off (SSID Broadcast refusal).

In such cases, enter the same SSID as the wireless LAN router (base

unit) directly.

• It is recommended that you connect to an SSID with an RSSI (Received

Signal Strength Indication) of 50 or above.

gFollow the procedure in “1 Check the network that you are attempting

to connect to.” to set up this unit.

Refer to “■ When using WEP security settings” in the table on the reverse

page to set up this unit.

aEnter the profile name of your choice in “profile name”.

bWhen (2) in the table is “Open”

^Select “Open” under “Encryption”.

When (2) in the table is “Shared”

^Select “SHARED” under “Encryption”.

cWhen (5) in the table is set to use a 10 or 5 letter password

^Select “64Bit” under “Key Length”.

When (5) in the table is set to use a 26 or 13 letter password

^Select “128Bit” under “Key Length”.

dWhen (3) in the table is “Hexadecimal”

^Select “Hex” under “Key Format”.

When (3) in the table is “ASCII”

^Select “ASCII” under “Key Format”.

eEnter the same encryption key

as in (5) on the table in the

same Encryption key field as in

(4) in the table.

For example, when (4) in the

table is “Key 1”, enter the same

password as “Encryption Key

1” from (5) in the table.

fSelect the same default key as

(4) from the table in “Default Tx

Key”.

gClick [APPLY].

Refer to “■ When using WPA/WPA2 security settings” in the table on the

reverse page to set up this unit.

aEnter the profile name of your

choice in “profile name”.

bEnter the same password as in

(4) from the table in the “Pre-

shared Key” field.

cClick [APPLY].

Note

To register multiple base units repeat procedures e through g.

When (2) in the table is “Open / Shared”

When (2) in the table is “WPA-PSK”/“WPA2-PSK”

hThe “LAN Setup” screen appears. Change the IP address if it is already

being used by another device.

Check the settings and click [APPLY].

iThe seconds before this unit restarts are counted down (30 seconds).

When the count reaches “0”, this unit will restart. Click “OK” and check

that this unit can connect to the access point.

jClose the browser.

kRemove the connected LAN cable and USB power cable.

aUse the supplied LAN cable to connect the LAN1 port (or the LAN2 port)

on this unit to the NETWORK port on the AV product. Then, use the

supplied USB power cable to connect the power connector on this unit

to the DC OUT jack on the AV product.

The indicator on the front panel of this unit lights. Wait for approximately one

minute and then carry out the following procedure.

Note

If the AV product is not equipped with a DC OUT jack, connect to the USB

connector on the front panel.

bTurn on the power of the AV product that you wish to connect this unit

to.

cCheck that the network functions of the connected AV products

function correctly.

Refer to the owner’s manual of the AV product for information on these

network functions.

■The power does not turn on

• Check that the USB power cable is firmly connected to this unit and the AV

product.

• Check that the AV Receiver Network Standby is set to ON. (If Network

Standby is OFF, power supply to the DC OUT jack will turn OFF when the AV

Receiver is set to Standby.)

■Cannot connect using WPS

• Only some devices are WPS compatible. If you are unable to connect using

WPS, configure the settings manually.

■An error occurs when “ywa.setup” or “192.168.1.249” is input in the

address field of the web browser, or the login screen does not appear.

• Check the IP address settings (automatic or fixed setting) of the PC. If the

PC is set to fixed setting, change it to automatic.

• The IP address of this unit may have changed from its default setting. Refer

to “Resetting this unit” and reset this unit.

• If you are using any security software, turn it off temporarily. Refer to the

owner’s manual of the security software for information on how to turn it off.

• If the wireless channel of the base unit is set to “12” or “13”, change it to a

channel between “1” and “11”. (USA and Canada models only)

■Cannot log in from the login screen

• The ID and password may have been changed. Refer to “Resetting this unit”

and reset this unit.

This completes connection with the base unit. Proceed to “Step 3

Connecting to an AV product”.

Step 3 Connecting to an AV product

This completes the setup procedure.

Troubleshooting

AV Receiver

Rear Panel

■Unable to find the base unit in “Wireless Site Survey” on the setup

screen

• If this unit is too far away from the base unit (wireless LAN router, etc.) or

there is an obstacle between them, try searching again in close proximity to

the base unit, in a location where there are no obstacles between the two

devices.

• The base unit may be set to refuse SSID Broadcast. Set the SSID, security

mode, and key by hand.

■Unable to configure settings in “Wireless Site Survey” on the setup

screen

• Check the SSID. If the base unit SSID or password contain characters that

this unit cannot use, the password is greater than 30 characters long, or the

SSID is greater than 32 characters long, change them to settings that are

compatible with this unit.

• Check the base unit security mode, and set the same security mode on the

YWA-10 setup screen.

• The password you have entered may be incorrect. Check the password and

re-enter it.

• If multiple base units are registered, select the units to which you wish to

connect, and click [Connect].

■Not connected to the Internet, or connected to the Internet, but

experiencing sound skipping.

• There may be a problem with your Internet environment. Without using this

unit, check whether your PC can connect to the Internet, as in Step 1.

• Refer to “Step 3 Connecting to an AV product” and check that the products

and cables are connected correctly.

• If this unit is too far away from the base unit (wireless LAN router, etc.) or

there is an obstacle between them, try searching again in close proximity to

the base unit, in a location where there are no obstacles between the two

devices.

• If there is a microwave oven in the immediate area, electromagnetic waves

from the microwave oven may be interfering with the wireless transmissions.

Move further away from the microwave oven and try connecting again.

• The base unit may be restricting connections by MAC Address. Add the MAC

address written on the underside of this unit to the list of permitted

connections on the base unit.

• Turn on the power to this unit again.

• Turn on the power to the base unit (wireless LAN router, etc) again.

• Check the IP address settings (automatic or fixed setting) of the network

device to which this product is to be connected. If the network device is set to

fixed setting, change it to automatic.

• Check that the DHCP server function on the base unit is set to ON.

• Try removing and reinserting the LAN cable connecting this unit and the AV

Receiver.

• Connection is not possible if multiple YWA-10 units are in use, or if another

device is using the IP address “192.168.xxx.249”. Refer to “Changing the IP

address” and change to a unique IP address.

• If you are unable to connect even after performing the above procedure,

reset this unit. Refer to “Resetting this unit” for information on resetting.

• Audio content that utilizes a significant amount of data may not transmit

correctly over a wireless connection in some cases. Use audio formats that

require a small amount of data.

Note

Resetting this unit will erase all of its settings. Be sure to note down the

necessary information before resetting.

aCheck that this unit’s power is on.

bPress the Reset button for at least 10 seconds.

cRelease the Reset button when all the indicators are blinking.

When this unit restarts after approximately 2 minutes, resetting is complete.

When resetting is complete, set up this unit again, starting from “Step 2-A

Connecting to the base unit (using WPS)” or “Step 2-B Connecting to the base

unit (manual configuration)”.

aReset this unit.

Refer to “Resetting this unit”.

bConnect this unit to a PC.

Refer to “2 Connect this unit to a PC” in “Step 2-B Connecting to the base

unit (manual configuration)”.

cOpen the setting screen of this unit.

Refer to “3 Setting up this unit” in “Step 2-B Connecting to the base unit

(manual configuration)”, and carry out procedures 1-3.

dClick “Network” in the menu in the upper area of the setting screen.

eOn the “LAN Setup” screen, enter “192.168.1.xxx” as an IP address.

Set the “xxx” in “192.168.1.xxx” to a number that is between 2 and 248, and

one that is not used by other devices.

fClick [APPLY].

gSet up this unit again.

Carry out “Step 2-A Connecting to the base unit (using WPS),” or “Step 2-B

Connecting to the base unit (manual configuration)”.

Resetting this unit

Changing the IP address

User name (Login ID): admin

IP address: 192.168.1.249

Password: password

Wireless section

Wireless type .................................. IEEE802.11n, IEEE802.11g, IEEE802.11b

Frequency of operation ..........................................US: 1—11 ch, EU: 1—13 ch

Frequency band ................................................ 2.4 GHz (2,400—2,483.5 MHz)

Type of modulation ...................... IEEE802.11n: OFDM, IEEE802.11g: OFDM,

IEEE802.11b: DSSS

Antenna gain...............................................................................................2 dBi

Antenna...................................................................Internal antenna x 2 (2T2R)

Access mode .......................................................................Infrastracture mode

Bandwidth .......................................................................... 20 MHz and 40 MHz

Security ...................WPA2-PSK (TKIP), WPA2-PSK (AES), WPA-PSK (TKIP),

WPA-PSK (AES), SHARED, OPEN (WEP: 64bit/128bit,

Key format: ASCII/Hexadecimal), Disabled (No encryption)

Wired section

Ethernet type......................IEEE802.3u (100Base-Tx), IEEE802.3i (10Base-T)

Interface ....................................................................... RJ-45 port x 2 (LAN x 2)

Ethernet cable......................................................................Category 5 or more

Configuration window requirement

OS............................................... Windows 7(32bit/64bit)/Vista(32bit/64bit)/XP,

Mac OS X 10.4/10.5/10.6, CPU: Intel/PowerPC support)

Browser................................ Internet Explorer 6 or above, Firefox 5.0 or above

General

Dissipation power.......................................... Maximum of approximately 2.3 W

Power supply ................................................................................DC +5V 0.5 A

External dimensions.......................... 78 x 70 x 22 (mm) *Excluding protrusions

Weight..........................................................................................................62 g

Operating temperature range.........................................Temperature: 0—40 °C

Humidity: 10—90 % (No condensation)

Strage temperature range..........................................Temperature: –20—60 °C

Humidity: 10—90 % (No condensation)

* Specifications are subject to change without notice.

Factory default settings

Specifications

(E.U. only)

This symbol mark is according to the EU directive 2002/96/EC.This symbol

mark means that electrical and electronic equipment, at their end-of-life, should

be disposed of separately from your household waste. Please act according to

your local rules and do not dispose of your old products with your normal

household waste.

■Precautions

Read this before using this unit.

To assure the finest performance, please read this manual carefully. Keep it in a safe place

for future reference.

1 Install this unit in a cool, dry, clean place away from direct sunlight, heat sources, and

sources of excessive vibration, dust, moisture, and/or cold. (Do not use/keep this unit in

a car etc.)

2 Locate this unit away from other electrical appliances, motors, or transformers to avoid

humming sounds.

3 Do not expose this unit to sudden temperature changes from cold to hot, and do not

locate this unit in an environment with high humidity (i.e. a room with a humidifier) to

prevent condensation inside this unit, which may cause an electrical shock, fire, damage

to this unit, and/or personal injury.

4 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean,

dry cloth.

5 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel

when any service is needed. The cabinet should never be opened for any reason.

6 Be sure to read the “Troubleshooting” section regarding common operating errors before

concluding that the unit is faulty.

7 Before moving this unit, disconnect USB power cable from the AV product.

Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or

defibrillator implant.

Explanations regarding GPL

This product utilizes GPL/LGPL open-source software in some sections. You have the right

to obtain, duplicate, modify, and redistribute this open-source code only. For information on

GPL/LGPL open source software, how to obtain it, and the GPL/LGPL license, refer to the

Yamaha Corporation website (http://download.yamaha.com/sourcecodes/ywa-10/).

• This product is limited to indoor use only.

• Frequencies used by this product may be prohibited to use in some counties. As a user of

this product, you have responsibilities to use this product only in the intended countries

and confirm that this product is set to use frequencies and channels that are allowed to

use in your country. Violators may be punishable by law of the country. For information

about laws of each country, please refer to “ERC/REC 70-03”.

We, the manufacturer (Yamaha Corporation) hereby declare that this equipment (Wireless

Network Adapter), model YWA-10 is in compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

• Microsoft, Windows 7, Windows Vista and Windows XP are registered trademarks or

trademarks of Microsoft Corporation in the U.S. and other countries.

• Other product names, technology names, and company names mentioned in this manual may

be trademarks or registered trademarks of their respective owners and are hereby

acknowledged.

YWA-10_dtp_En.fm Page 2 Thursday, April 12, 2012 12:07 AM

Product specificaties

Merk:	Yamaha
Categorie:	Draadloos audio systeem
Model:	YWA-10
Kleur van het product:	Zwart
Gewicht:	62 g
Breedte:	78 mm
Diepte:	70 mm
Hoogte:	20 mm
LED-indicatoren:	Ja
Wi-Fi-standaarden:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Connectiviteitstechnologie:	Bedraad en draadloos
Ethernet LAN:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	2
Aantal USB-aansluitingen:	1
Interface:	Ethernet
Wifi-standaard:	Wi-Fi 4 (802.11n)
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Intern:	Nee
Ondersteunde WLAN data-overdrachtsnelheden:	11, 24, 54, 300 Mbit/s
Hostinterface:	Draadloos
Maximale overdrachtssnelheid van gegevens:	300 Mbit/s
Wifi:	Ja