Yamaha VXC4 Handleiding

Yamaha Speaker VXC4

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha VXC4 (11 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the

possibility of serious injury or even death from electrical shock, short-

circuiting, damages, fire or other hazards. These precautions inc lude,

but are not limited to, the following:

• This device contains no user-serviceable parts. Do not open the device

or attempt to disassemble the internal parts or modify them in any way. If

it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or

glasses) containing liquids which might spill into any openings. If any

liquid such as water seeps into the device, have the device inspected by

qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the

possibility of physical injury to you or others, or damage to the device

or other property. These precautions include, but are not limited to,

the following:

• Do not place the device in an unstable position where it might

accidentally fall over.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Construction work should be carried out in accordance with construction-

related law and always by a professional constructor. If the device

installation requires construction work, make sure to observe the

following precautions.

- Choose mounting hardware and an installation location that can

support the weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• Before connecting the device to a power amplifier, turn off the power for

all devices. Before turning the power on or off for all devices, set all

volume levels to minimum.

• Use only speaker cables for connecting speakers to the speaker jacks.

Use of other types of cables may result in fire.

• Do not wipe the outer packaging with benzine, thinner, or synthetic

detergent and do not use electrical contact cleaner. These may damage

the outer packaging and dissolve the parts.

• Do not insert your fingers or hands in any gaps or openings on the device

(ports).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (ports). If this happens, have the

device inspected by qualified Yamaha service personnel.

PRECAUTIONS

Do not open

Water warning

Location

Connections

Maintenance

Handling caution

• Do not operate the device if the sound is distorting. Prolonged use in this

condition could cause overheating and result in fire.

• When choosing a power amplifier for use with this device, make sure that

the output power of the amplifier is lower than the power capacity of this

device (see SPECIFICATIONS).

Even if the output power of the amplifier is lower than the power capacity

of this device (program), use of excessive input signals resulting in

clipping may cause damage to the device.

Malfunction or fire may occur especially when the following sounds or

noises are generated:

- feedback, when using a microphone

- continuous and extreme volume sound from a musical instrument

- extreme continuous distorted sound

- noise caused by plugging/unplugging the cable while the amplifier is

turned on

NOTICE

To avoid the possibility of malfunction/damage to the product, damage to

data, or damage to other property, follow the notices below.

ƔHandling and Maintenance

• Do not place vinyl, plastic or rubber objects on the device, since this

might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint

thinners, solvents, cleaning fluids, or chemical-impregnated wiping

cloths.

• Condensation can occur in the device due to rapid, drastic changes in

ambient temperature-when the device is moved from one location to

another, or air conditioning is turned on or off, for example. Using the

device while condensation is present can cause damage. If there is

reason to believe that condensation might have occurred, leave the

device for several hours until the condensation has completely dried out.

• Be sure to observe the amplifier’s rated load impedance (see

SPECIFICATIONS), particularly when connecting speakers in parallel.

Connecting an impedance load outside the amplifier’s rated range can

damage the amplifier.

• When connecting the speakers with high impedance, be sure that the

total rated input capacity of the speakers does not exceed the output

power of the amplifier.

• When using a high-impedance speaker connection, make sure the audio

signal is passed through an 80 Hz or above high-pass filter before being

input to the speakers.

• ABOUT THE PROTECTION CIRCUIT

This speaker system has an internal protection circuit that shuts off the

speaker unit when an excessive input signal is applied.

If the speaker unit emits no sound, reduce the volume level of the

amplifier immediately.

The sound will return automatically in several seconds.

• Do not swing the speaker by its strap.

• Do not place the speaker face down with the grille attached, as

deformation of the grille may result.

• When placing the speaker face down, always place it on a flat and

smooth surface.

• Do not touch the speaker driver unit.

ƔAbout This Manual

The illustrations as shown in this manual are for instructional purposes only,

and may appear somewhat different from those on your device.

The contents of this manual apply to the latest specifications as of the

printing date. Since Yamaha makes continuous improvements to the

product, this manual may not apply to the specifications of your particular

product. To obtain the latest manual, access the Yamaha website then

download the manual file. Since specifications, equipment or separately

sold accessories may not be the same in every locale, please check with

your Yamaha dealer.

Yamaha cannot be held responsible for damage caused by improper use

or modifications to the device.

UNPACKING

Unpack the contents and confirm that all the following items are included.

* Speaker cable and safety wire are not included.

SPECIFICATIONS

*1: Half-space (2π)

*2: Calculated based on power rating and sensitivity, exclusive of power compression.

*3: 30 mm or less for the Anti-Drop Tab.

DIMENSIONS

• Speaker × 2 • Grille × 2 • O-ring × 2 • Tile Rail × 4

• Screw × 4 • Cutout Template × 1 • Owner’s Manual (this manual)

Type Full Range with Back Can, Bass-reflex

Component 4" (10 cm) Full Range

Coverage Angle (500 Hz – 4 kHz on average) 130° conical

Nominal Impedance 8 Ω

Power Rating NOISE 30 W

PGM 60 W

MAX 120 W

Sensitivity (1W, 1m) *187 dB SPL

Maximum SPL (Calculated, 1m) *2108 dB SPL

Frequency Range (-10 dB) *180 Hz – 20 kHz

Connector Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)

Max. wire size 12 AWG (2.5 mm2)

Transformer Taps 70 V 30 W, 15 W, 7.5 W, 3.8 W

100 V 30 W, 15 W, 7.5 W

Overload Protection PolySwitch

Magnetically Shielded No

Enclosure Shape Back Can

Back Can Material Steel 1mm, Black

Baffle Material HIPS

Grille Material Powder coated perforated steel (t=0.6 mm)

Trim Ring: ABS

Aperture ratio: 51%

Finish VXC4 : Black painting (approximate value: Munsell N3)

VXC4W : White painting (approximate value: Munsell 9.3)

Dimensions (Speaker only) Ø225 × 194H mm (Ø8 7/8" × 7 5/8"H)

Net Weight (Speaker only, 1 piece) 2.6 kg (5.7 lbs)

Cutout Size Ø186 mm (Ø7 5/16")

Required ceiling board thickness 5 mm – 35 mm *3

Conduit Tube Up to 1/2"

Packaging Packaged in pair

243

164

Ø243

Ø183

608

644

O-ringVXC4/VXC4W

Unit: mm

Tile Rail

INSTALLING THE SPEAKERS

Install the speakers onto the ceiling with the supplied hardware. Ensure that

the strength of the ceiling rail is sufficiently strong.

Pre-installation (Preparation of the Cable)

Use stranded wire for cables attached to the Euroblock connector. Strip

their insulation as shown in the figure and connect them.

NOTE

Do not plate stranded wires by solder. Doing so will cause the wire to break.

1Put the supplied cutout template to the ceiling and draw a circle by

tracing it.

Make sure to use the cutout template so that hole is the correct

diameter.

NOTE

If you use a circular cutter, set the diameter with the cutout template.

2Cut the hole by tracing the circle.

Be careful to prevent chips or powder entering your eyes while

cutting the hole.

1Insert the two tile rails through the cut hole and place them on the

ceiling surface within your reach. Be sure that each tile rails are

oriented as shown below.

2Insert the folded O-ring through the cut hole and open it in the ceiling.

3Secure the O-ring and tile rails with supplied two screws through

either slot of both O-ring brackets.

1Pull the wiring from the amplifier through the cut hole.

2Loosen the screw at the right of the terminal cover to open the

terminal cover and remove the Euroblock connector.

3After loosening the terminal screws of the Euroblock connector with a

flat-blade screwdriver, insert the cable into each terminal and tighten

the screws. Make sure that cables cannot be pulled out.

NOTE

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).

1CUT OUT A HOLE IN THE CEILING

2INSTALL THE TILE RAILS AND O-RING

3CONNECT THE WIRING TO THE CONNECTOR AND FIX

THE CABLE

About 7 mm (0.3 in.)

Terminal cover

Euroblock connector

Less than 3 mm (0.1 in.)

There are two acceptable wiring methods.

CAUTION

When connecting with low impedance, take note of the combined

resistance.

Using Loop-Through Terminals

For this method, cables are connected from terminals 1 and 4 to the

subsequent speaker. If the Euroblock connector is disconnected from

a speaker, all subsequent speakers will not work. This can be useful

to identify which speaker has a problem.

Paralleling Input Terminals

For this method, cables are connected to terminals 2 and 3 of each

speaker. Since the cables are connected via Euroblock connectors,

subsequent speakers can work even if a problem occurs with a

speaker.

4Plug the connected Euroblock connector into the socket in the

speaker.

5Loosen the screw A of the strain relief clamp.

6Remove the screw B of the strain relief clamp.

If the cable is not to be held, remove the screw A and remove the

strain relief fitting, then proceed to step 8.

From amplifier or

previous speakers To subsequent

speakers

subsequent

speakers

Euroblock

connector

Power

amplifier

Speaker

From amplifier or

previous speakers

To subsequent

speakers

Power

amplifier

Speaker

Euroblock

connector

subsequent

speakers

7Hold the cable in the strain relief clamp, then tighten screws A and B.

8Close the terminal cover and tighten the screw.

1Attach the safety wire to the safety wire ring, and connect the wire to

an independent support point, such as a joist.

CAUTION

Always take measures to prevent the speaker falling down.

If the safety wire is too short, prepare another wire appropriate for the

speaker weight and installation conditions. If the wire is too long,

should the speaker fall, the wire may break as a result of too much

strain.

2Push up the speaker slowly into the ceiling, taking care not to trap the

cable.

4FIX THE SPEAKERS ONTO THE CEILING

Screw

Safety wire ring

Anti-Drop Tab

When all the Anti-Drop Tabs

cross over the O-ring, the

speaker is held temporarily. You

can release your hands from the

speaker.

To release the speaker from the

O-ring, press the Anti-Drop Tabs.

These are located above the U

mark near the edge of the

cabinet’s face.

3Turn the screwdriver a half turn counterclockwise to loosen the

attachment screw. This makes the clamp easier to align in the

channel.

4Turn the screwdriver clockwise to tighten the attachment screw.

The first turn of the attachment screw aligns the clamp with the

channel. Further turns move the clamp down the channel to pull the

speaker up into the ceiling.

CAUTION

• Do not over-tighten the attachment screw. Otherwise, the

attachment screw and clamp will break.

• Do not turn any screws that do not have a guide sleeve in the screw

hole. Otherwise, the speaker may fall or malfunction.

Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/

70V line distributed system, by rotating the tap selector switch on the front

side of the speaker with a flat-blade screwdriver.

CAUTION

The “X” position should not be selected. The 8Ω position should be selected

for 8Ω audio systems only. If the setting is incorrect, it may cause

malfunction of the speaker and amplifier.

Fit the grille to the cabinet front and turn it clockwise.

CAUTION

The grille may fall down if it is attached inadequately. Attach it firmly.

5SET THE LINE VOLTAGE/IMPEDANCE AND POWER

6ATTACH THE GRILLE

Clamp

Owner’s Manual

Ceiling Speaker

English

ZE19530

Information for Users on Collection and Disposal of

Old Equipment

English

This symbol on the products, packaging, and/or accompanying

documents means that used electrical and electronic products should not

be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take

them to applicable collection points, in accordance with your national

legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please

contact your local authorities or dealer and ask for the correct method of disposal.

Verbraucherinformation zur Sammlung und Entsorgung alter

Elektrogeräte

Deutsch

Befindet sich dieses Symbol auf den Produkten, der Verpackung und/

oder beiliegenden Unterlagen, so sollten benutzte elektrische Geräte

nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen und den

Richtlinien 2002/96/EG bringen Sie alte Geräte bitte zur fachgerechten

Entsorgung, Wiederaufbereitung und Wiederverwendung zu den

entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie,

wertvolle Ressourcen zu schützen, und verhindern mögliche negative

Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch

unsachgerechte Müllentsorgung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte

kontaktieren Sie bitte Ihre örtliche Stadt- oder Gemeindeverwaltung, Ihren

Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

[Information für geschäftliche Anwender in der Europäischen Union]

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder

Zulieferer für weitere Informationen.

[Entsorgungsinf ormation für Länder außerhalb der Europäischen Union]

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel

ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler

und fragen Sie nach der sachgerechten Entsorgungsmethode.

Information concernant la Collecte et le Traitement des

déchets d’équipements électriques et électroniques.

Français

Le symbole sur les produits, l'emballage et/ou les documents joints

signifie que les produits électriques ou électroniques usagés ne doivent

pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des

déchets d’équipements électriques et électroniques, veuillez les déposer

aux points de collecte prévus à cet effet, conformément à la

réglementation nationale et aux Directives 2002/96/CE.

En vous débarrassant correctement des déchets d’équipements

électriques et électroniques, vous contribuerez à la sauvegarde de

précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine

qui pourraient advenir lors d'un traitement inapproprié des déchets.

Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements

électriques et électroniques, veuillez contacter votre municipalité, votre service de

traitement des déchets ou le point de vente où vous avez acheté les produits.

[Pour les professionnels dans l'Union Européenne]

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et

électroniques veuillez contacter votre vendeur ou fournisseur pour plus d'informations.

[Information sur le traitement dans d'autres pays en dehors de l'Union Européenne]

Ce symbole est seulement valable dans l'Union Européenne. Si vous souhaitez vous

débarrasser de déchets d’équipements électriques et électroniques, veuillez contacter les

autorités locales ou votre fournisseur et demander la méthode de traitement appropriée.

Información para los usuarios acerca de la recogida y

desecho de equipos antiguos

Español

Este símbolo en los productos, embalajes y/o documentos adjuntos

indica que los productos eléctricos y electrónicos usados no deben

mezclarse con la basura doméstica normal.

Lleve los productos antiguos a los puntos de recogida pertinentes, de

acuerdo con la legislación nacional y la Directiva 2002/96/CE, para

conseguir así un tratamiento, recuperación y reciclaje adecuados.

Si se deshace correctamente de estos productos, contribuirá a ahorrar

valiosos recursos y a impedir los posibles efectos adversos que sobre la

salud humana y el medio ambiente podría provocar la incorrecta

manipulación de la basura.

Póngase en contacto con su ayuntamiento, con el departamento de eliminación de basuras

o con el establecimiento donde adquirió los artículos y obtenga más información acerca de

la recogida y reciclaje de productos antiguos.

[Para usuarios profesionales de la Unión Europea]

Si desea desechar equipos eléctricos y electrónicos, póngase en contacto con su

distribuidor o proveedor para obtener más información.

[Información acerca del desecho en países fuera del ámbito de la Unión Europea]

Este símbolo solo es válido dentro de la Unión Euro pea. Si desea desechar estos artículos,

póngase en contacto con las autoridades municipales o con su distribuidor, e infórmese

acerca del método correcto de hacerlo.

Informazioni per gli utenti sulla raccolta e lo smaltimento di

vecchia attrezzatura

Italiano

La presenza di questo simbolo sui prodotti, sull’imballaggio, e/o sui

documenti che li accompagnano avverte l’utente che i prodotti elettrici ed

elettronici usati non devono essere associati ai rifiuti domestici generici.

Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti,

consegnarli ai punti di raccolta specifici in accordo con la propria

legislazione nazionale e la direttiva 2002/96/CE.

Smaltendo correttamente questi prodotti, si contribuisce al risparmio di risorse

preziose e a prevenire alcuni potenziali effetti negativi sulla salute umana e

l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei

rifiuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, contattare la propria

amministrazione comunale, il servizio di smaltimento dei rifiuti o il punto vendita dove i

prodotti sono stati acquistati.

[Per le aziende dell’Unione europea]

Se si desidera disfarsi di prodotti elettrici ed elettronici, contattare il rivenditore o il fornitore

per ulteriori informazioni.

[Informazioni sullo smaltimento negli altri Paesi al di fuori dell’Unione europea]

Il presente simbolo è valido solamente nell’Unione europea. Se si desidera disfarsi di questi

articoli, contattare le autorità locali o il rivenditore per informarsi sulle corrette modalità di

smaltimento.

Manual Development Department

Published 03/2015 YKZC-D0

Printed in Indonesia

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

This manual describes the procedure for painting the grilles and enclosures of the VXS and VXC series speakers.

It is recommended to use acrylic lacquer paint for the enclosure of the VXS series. Follow the instructions provided with the

paint.

1Remove the emblem on the front of the grille.

• The emblem is attached by adhesive tape.

2Remove the screw behind the emblem, using a

crosshead screw driver.

3Remove the speaker grille.

• Remove the grille using a narrow, pointed tool.

• Remove the corner of the grille first.

Using excessive force may distort the grille.

• Be careful not to damage the butyl rubber on the inner edge of the

grille.

1Paint the grille using spray-type paint.

2Allow the applied paint to completely dry.

1Remove any dust, etc., with a lint-free cloth.

• Do not sand the enclosure surface.

2Paint the enclosure using spray-type paint.

• Cover the baffle and connectors using masking materials to avoid

paint contact.

3Allow the applied paint to completely dry.

VXS series

CAUTION The enclosure of the subwoofer (VXS10S / VXS10SW / VXS10ST / VXS10STW) is PVC coated,

and therefore should not be painted.

Removing the grille

Painting the grille

Painting the enclosure

English

Speaker system painting guide

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	VXC4
Kleur van het product:	Zwart
Gewicht:	2600 g
Breedte:	- mm
Diepte:	195 mm
Hoogte:	- mm
Connectiviteitstechnologie:	Bedraad
Diameter:	225 mm
Gemiddeld vermogen:	30 W
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	1
Peak Music Power Output (PMPO):	120 W
Frequentiebereik:	80 - 20000 Hz
Gevoeligheid:	87 dB
Luidspreker soort:	Volledig bereik
Diameter mid-range driver:	4 "
Aantal Euroblock-ingangsconnectoren:	1