Yamaha MY16-ES64 Handleiding

Yamaha Niet gecategoriseerd MY16-ES64

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha MY16-ES64 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

OWNER’S MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

MANUALE DI ISTRUZIONI

取扱説明書

OWNER’S MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

MANUALE DI ISTRUZIONI

取扱説明書

日本語中文 ITALIANO ESPAÑOL FRANÇAIS DEUTSCH ENGLISH

EtherSound®

INTERFACE CARD

EtherSound®

INTERFACE CARD

MY16-ES64

2MY16-ES64 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : EtherSound INTERFACE CARD

Model Name : MY16-ES64

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

• This applies only to products distributed by Yamaha Canada Music Ltd. (class B)

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

(class b korea)

ENGLISH

MY16-ES64 Owner’s Manual 3

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injur y or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not

limited to, the following:

• Before installing the card in an audio device please check to make sure that the device is compatible with the card and check possible restrictions

regarding the maximum number of Yamaha and third-party expansion cards that can be simultaneously installed. Refer to the owner manual supplied ’s

with the audio device, and/or the Yamaha Pro Audio web site at:

http://www.yamahaproaudio.com/

• Do not install the card in any Yamaha products not speciﬁed by Yamaha for use with the card to avoid possible electrical shock, ﬁre, or equipment

damage.

• Do not attempt to disassemble or modify the card. Do not apply excessive force to card connectors or other card components. Mishandling of the card

may lead to shock, ﬁre hazard, or equipment failure.

• Be sure to disconnect the power cable of the host device before installing the card and connecting/disconnecting the cables (in order to eliminate shock

hazard, undesired noise, and avoid equipment damage).

• Turn off all peripheral devices connected to the host device before installation, and unplug all related cables.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injur y to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Be sure to properly ground the host device to prevent electrical shock and/or malfunction.

• Do not touch the metallic leads (pins) of the circuit board when handling the card. The pins are sharp and may cause hand cuts.

• Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands on sharp edges.

• Avoid touching exposed connectors and metal parts to minimize the possibility of bad connections.

• Drain all static electricity from your clothing and body before handling the card. Static electricity can damage the card. Touch an exposed metal part of the

host device or other grounded object beforehand.

• Do not drop the card or subject it to physical shock as this can result in breakage and/or malfunction.

• Do not drop screws or other small parts inside the card. If power is applied while screws or similar metal objects are loose inside the unit the card may

malfunction or be damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualiﬁed Yamaha service personnel.