WyreStorm EX-35-H2-ARC Handleiding

WyreStorm AV extender EX-35-H2-ARC

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm EX-35-H2-ARC (3 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

18Gbps 4K HDR HDBaseT Extender with

True ARC and Audio Breakout

EX-35-H2-ARC Quickstart Guide

EX-35-H2-ARC Quickstart Guide | 181012

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-35-H2-ARC Transmitter

1x EX-35-H2-ARC Receiver

1x 12V DC 3A Power Supply (US/EU/UK)

3x 3‐pin Screw Down Male Phoenix Connectors

1x IR Emitter

1x IR Receiver

4x Mounting Brackets (2x for TX | 2x for RX)

1x Quickstart Guide (this document)

HDMI HDMI

Audio Return

Channel

12V DC 3A

Power Supply

EX-35-H2-ARC Transmitter (TX) EX-35-H2-ARC Receiver (RX)

4K HLG Source

4K HDR Source

4K HDR HDMI Display

HDMI

Audio Return

Channel

KEY

HDMI

HDBaseT

Power

Audio Return Channel

HDBaseT

Cat6/6a/7

Note: S/PDIF I/O also available for audio return

Note: Extender set may be powered by either the TX or RX.

Only one power supply is required.

AV Receiver

Front Panel (TX/RX) Rear Panel (TX/RX)

Power LED Solid: The receiver is powered On

Off: The receiver is powered Off

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

HDCP LED

Solid: HDCP content is present.

Flashing: HDCP content is not present.

Off: No signal.

LINK LED

Solid: Link to receiver has been established.

Flashing: Link to receiver has not been

established.

Source Audio Out Use this connection to send audio separate

from the HDMI connection to the RX.

Audio Return Input

Set the switch to ARC to receive audio from

the display via the HDMI connection.

Set the switch to S/PDIF In to receive audio

from the display via the S/PDI In connection.

Power In

5.5mm Screw Down Barrel Jack

Connect to the included 18V DC 1A power

supply to the transmitter or receiver. A power

supply is not required on the other end as it

will be powered using PoH..

HDBT In

HDBT Out

8-pin RJ-45 female

Connect the transmitters HDBT Out to

receivers HDBT In.

IR TX

IR RX

IR TX - 3.5mm (1/8in) Mono Jack: Connect

to the supplied IR emitter to control a local

device from the remote display location via

HDBaseT.

IR RX - 3.5mm (1/8in) Stereo Jack: Connect

to the supplied IR receiver to send IR to the

remote display location via HDBaseT.

See for more IR TX/RX Guidelines

information.

RS-232 1x RS-232: 3-pin Phoenix

HDMI In

HDMI Out

19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

S/PDIF In/Out

S/PDIF Out on the TX transmits audio from

the RX received via HDBaseT.

S/PDIF In on the RX receives audio to be sent

to the TX via HDBaseT. Audio Return Input

switch must be set to S/PDIF in order for

audio to be transmitted.

EX-35-H2-ARC Quickstart Guide | 181012

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

EX-35-H2-ARC Transmitter (TX)

EX-35-H2-ARC Receiver (RX)

A B C D E F

EX-35-H2-ARC Transmitter (TX)

EX-35-H2-ARC Receiver (RX)

A B C D E F

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device.

• Verify that all HDMI and HDBaseT connections are not loose and are

functioning properly.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• Congure EDID Settings to a lower resolution.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the

Wiring and Connections section.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

EX-35-H2-ARC Quickstart Guide | 181012

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received by the NetworkHD

system. Other 3rd party emitters and receivers can be used; however, these

devices must operate in the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

The EX-35-H2-ARC uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary from

device to device. Refer to the documentation for the connected device for pin

functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Audio Return Input

This receiver contains a switch that determines where the Audio Return is

received to be sent back to the transmitter. Set this switch based on the

connections being used to send and receive audio. Set the switch to ARC to receive audio from the

display via the HDMI connection.

Set the switch to S/PDIF In to receive audio from the

display via the S/PDI In connection.

Product specificaties

Merk:	WyreStorm
Categorie:	AV extender
Model:	EX-35-H2-ARC
Kleur van het product:	Zwart
Gewicht:	360 g
Breedte:	195 mm
Diepte:	94.8 mm
Hoogte:	21 mm
Soort:	AV-zender & ontvanger
Stroom:	3 A
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Ondersteunde video-modi:	1080p, 2160p
Maximum resolutie:	4096 x 2160 Pixels
Vermogensverbruik (max):	8.88 W
HDCP:	Ja
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
HDMI versie:	2.0
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080),3860 x 2160,4096 x 2160
Remote (IR) ingang:	1
Duurzaamheidscertificaten:	RoHS
Digitale audio, optische uitgang:	1
Temperatuur bij opslag:	-20 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
Externe adapter:	Ja
Rack-montage:	Ja
Audio-uitgangskanalen:	2.0 kanalen
HDBaseT-gecertificeerd:	Ja
Remote (IR) uitgang:	1
HDMI in:	1
RS-232 ingangspoorten:	1
RJ-45 uitgang ports:	1
HDCP versie:	2.2
Digitale audio optische in:	1
Bandbreedte:	9.2 Gbit/s
Aantal HDMI-uitgangen:	1
RJ-45 invoer ports:	1
Operating voltage:	12 V
HDBaseT-poort:	Ja
Maximaal bereik:	35 m
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Consumer Electronics Control (CEC)-ondersteuning:	Ja
Ondersteundende kabel types:	Cat6, Cat6a, Cat7, HDMI
3,5 mm-uitgang:	Ja
Extended display identification data (EDID):	Ja
Digitale audio optische-ingangstype:	TOSLINK
CEC-passthrough:	Ja