WyreStorm CAM-210 Handleiding

WyreStorm Bewakingscamera CAM-210

Lees hieronder de 📖 handleiding in het Nederlandse voor WyreStorm CAM-210 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quickstart Guide

CAM-210-PTZ Quickstart Guide | 230209

UK: +44 (0) 1793 676 683 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 2

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version, additional documentation, and conguration tools.

• Read through the section for important wiring guidelines before creating or choosing premade cables.Wiring and Connections

1080p60 PTZ Camera with USB 3.0,

HDMI Out, Auto Framing

CAM-210-PTZ

In the Box

1x CAM-210-PTZ Camera

1x 12V DC 1A PSU (US/UK/EU/AU)

1x IR Remote

1x Wall Mount

1x 2m 8 pin Mini Din RS-232 Cable

1x 1.5m USB 3.0 Type B Host Cable

1x QuickStart Guide

Basic Wiring Diagram

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

WyreStorm CAM-210-PTZ

Software Device Setup

Connecting To Zoom

To connect the WyreStorm CAM-210-PTZ to your Zoom software, rst navigate to your settings pane which can be found by clicking the gear icon in the top

right hand corner, then click on the Video tab. Here you can change the camera device by using the dropdown menus. Select WyreStorm CAM-210-PTZ under

the applicable options.

WyreStorm CAM-210-PTZ

Connecting To Microsoft Teams

To connect the WyreStorm CAM-210-PTZ to your Microsoft Teams software, rst navigate to your settings pane which can be found by clicking on your display

image in the top right hand corner, then click on the devices tab. Here you can change the camera device by using the dropdown menus. Select WyreStorm

CAM-210-PTZ under the applicable options.

CAM-210-PTZ Quickstart Guide | 230209

UK: +44 (0) 1793 676 683 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 2

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that WyreStorm CAM-210-PTZ has been selected in your software’s device

settings

• Check Web UI settings for Video resolution and Frame rate to ensure

compatibility with your software

• Verify that the device is not in standby

• Verify that power is being supplied to the device

• Verify that all connections are not loose and are functioning properly

• Verify that the RJ-45 cable is properly terminated following EIA568B standard

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to other

devices to verify functionality.

Default IP Address Default HTTP Port VISCA Control Port192.168.11.43 80 5678

Setup and Conguration

Accessing the Web UI

This camera is set to a default static IP Address (192.168.11.43). In order to communicate with it initially the PC must be set to a 192.168.11.xxx address with a

subnet of 255.255.0.0. This can be changed back once a static IP is set within a different range.

1. Connect the camera to the same network as a PC.

2. Open a web browser and enter the IP Address of the camera.

Username: admin | Password: admin

Using Control Software