Worx WG401E Handleiding
Worx
Schaafmachine
WG401E
Lees hieronder de š handleiding in het Nederlandse voor Worx WG401E (12 pagina's) in de categorie Schaafmachine. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
2
WARNING! Read all safety
warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, ļ¬re and/or serious
injury.
Save all warnings and instructions for
future reference.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
- Children should be supervised to ensure
that they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualiļ¬ed persons in order
to avoid a hazard.
SAFETY INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
SAFE OPERATING PRACTICES
1. TRAINING
Become familiar with the ownerās manual
before attempting to operate this equipment.
2. PREPARATION
1) Do not allow children to operate this
equipment.
2) Do not operate this equipment in the
vicinity of bystanders.
3) Wear ear protection and safety glasses at
all times while operating the machine.
4) Avoid wearing clothing that is loose ļ¬tting
or that has hanging cords or ties.
5) Only operate the machine in open space
(e.g. not close to a wall or other ļ¬xed
object) and on a ļ¬rm, level surface.
6) Do not operate the machine on a paved or
gavel surface where ejected material could
cause injury;
7) Before starting the machine, check that all
screws, nuts, bolts, and other fasteners
are properly secured and that guards and
screens are in place. Replace damaged or
unreadable labels.
3. OPERATION
1) Before starting the machine, look into the
feeding chamber to make certain that it is
empty.
2) Keep your face and body away from the
feed intake opening.
3) Do not allow hands or any other part of
the body or clothing inside the feeding
chamber, discharge chute, or near any
moving part.
4) Keep proper balance and footing at all
times. Do not overreach. Never stand at a
higher level than the base of the machine
when feeding material into it.
5) Always stand clear of the discharge zone
when operating this machine.
6) When feeding material into the machine
be extremely careful that pieces of metals,
rocks, bottles, cans or other foreign objects
are not included.
7) If the cutting mechanism strikes any foreign
objects or if the machine should start
making any unusual noise or vibration,
switch off the machine, disconnect the
supply and take the following steps:
ī ā¢īInspectīforīdamage;
ī ā¢īCheckīforīandītightenīanyīlooseīparts;
ī ā¢īHaveīanyīdamagedīpartsīreplacedīorī
repaired with parts having equivalent
speciļ¬cations.
8) Do not allow processed material to build
up in the discharge zone; this may prevent
proper discharge and can result in kickback
of material through the feed intake
opening;
9) If the machine becomes clogged, shut off
the power source and disconnect from
supply before cleaning debris. Keep the
power source clear of debris and other
accumulations to prevent damage to the
power source or possible ļ¬re. Remember
that operating the starting mechanism on
engine powered machines will still cause
3
the cutting means to move.
10) Keep all guards and deļ¬ectors in place and
in good working condition;
11) Do not tamper with the power source
governor settings; the governor controls
the safe maximum operating speed and
protects the power source and all moving
parts from damage caused by over-speed.
Seek authorized service if a problem exists.
12) Do not transport this machine while the
power source is running.
13) Shut off the power source and disconnect
the plug whenever you leave the work area.
14) Do not tilt the machine while the power
source is running.
4. MAINteNANce AND StoRAGe
1) When the machine is stopped for servicing,
inspection, or storage, or to change an
accessory, shut off the power source,
disconnect form supply, make sure that all
moving parts have come to a complete stop
and, where a key is ļ¬tted remove the key.
Allow the machine to cool before making
any inspections, adjustments, etc.
2) When servicing the cutting means be aware
that, even though the power source will
not start due to the interlock feature of the
guard, the cutting means can still be moved
by a manual starting mechanism.
5. ADDItIoNAL SAfety INStRuctIoNS
foR uNItS WIth BAGGING
AttAchMeNtS
1) Shut-off the power unit before attaching or
removing the bag;
Read the instruction manual,
before use.
Keep bystander or children away.
Danger - Rotating blades. Keep
hands and feet out of openings
while machine is running.
Wear eye and ear protection.
Remove plug from the mains
immediately if the cable is
damaged or cut
Double insulation
Wait until all machines
components have completely
stopped before touching them.
Do not use as a step
RCM approval mark
Product specificaties
Merk: | Worx |
Categorie: | Schaafmachine |
Model: | WG401E |
Kleur van het product: | Black,Metallic |
Gewicht: | 28000 g |
Geluidsniveau: | 90 dB |
Vermogen: | 2500 W |
Maaimethode: | Lemmet |
Snijcapaciteit: | 40 mm |
Capaciteit collecte bus: | - l |
Materiaal doorstroom: | 140 kg/h |
Automatische voeding: | Ja |
Heb je hulp nodig?
Als je hulp nodig hebt met Worx WG401E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schaafmachine Worx
5 Mei 2024
8 Maart 2023
28 Januari 2023
9 November 2022
Handleiding Schaafmachine
- Schaafmachine Bosch
- Schaafmachine AEG
- Schaafmachine DeWalt
- Schaafmachine WOLF-Garten
- Schaafmachine Bavaria
- Schaafmachine Black Decker
- Schaafmachine Bort
- Schaafmachine Einhell
- Schaafmachine Felisatti
- Schaafmachine Ferm
- Schaafmachine Gamma
- Schaafmachine Gardena
- Schaafmachine Global
- Schaafmachine Gude
- Schaafmachine Hammer
- Schaafmachine Hikoki
- Schaafmachine Hitachi
- Schaafmachine Makita
- Schaafmachine Metabo
- Schaafmachine Parkside
- Schaafmachine Powerplus
- Schaafmachine Protool
- Schaafmachine Robust
- Schaafmachine Rupes
- Schaafmachine Ryobi
- Schaafmachine Skil
- Schaafmachine Stihl
- Schaafmachine Stomer
- Schaafmachine Taurus
- Schaafmachine Topcraft
- Schaafmachine Triton
- Schaafmachine Varo
- Schaafmachine Ozito
- Schaafmachine Black And Decker
- Schaafmachine Cocraft
- Schaafmachine Meec Tools
- Schaafmachine Cotech
- Schaafmachine Fieldmann
- Schaafmachine Mafell
- Schaafmachine Proxxon
- Schaafmachine Porter-Cable
- Schaafmachine Herkules
- Schaafmachine Rikon
- Schaafmachine Surtek
- Schaafmachine Snow Joe
- Schaafmachine Alpha Tools
- Schaafmachine Max Bahr
- Schaafmachine Einhell Bavaria
- Schaafmachine McKenzie
- Schaafmachine Prowork
- Schaafmachine Proviel
- Schaafmachine XU1
- Schaafmachine Ergotools Pattfield
- Schaafmachine Bavaria By Einhell
Nieuwste handleidingen voor Schaafmachine
5 September 2024
5 September 2024
5 September 2024
5 September 2024
11 Juli 2024
11 Juli 2024
10 Juli 2024
10 Juli 2024
10 Juli 2024
11 Juni 2024