Workshop WS0900VA Handleiding

Workshop Stofzuiger WS0900VA

Lees hieronder de 📖 handleiding in het Nederlandse voor Workshop WS0900VA (18 pagina's) in de categorie Stofzuiger. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18
FOR QUESTIONS OR INFORMATION CONTACT US AT:
1-888-455-8724 from the US and Canada
www.WORKSHOPvacs.com
Part No. SP6863 Printed in Mexico
OWNER’S MANUAL
Español - página 15
Français - page 29
SAVE THIS MANUAL FOR FUTURE REFERENCE
WARNING:
To reduce the risk of injury, the user must read and understand the
owner’s manual before using this product.
!
MD
Wet/Dry Vac
6 U.S. Gallon/
22.5 Liter
• WS0600VA0
9 U.S. Gallon/
34.1 Liter
• WS0900VA0
SP6863-1 Workshop 6 9 GALLON:SP6439-3_ES.qxd 8/19/13 2:09 PM Page 1
5
Removal and Installation
of the Qwik Lock™ Filter
Filter Removal:
1. Hold the Filter tabs of the Qwik Lock™
Filter in each hand.
2. With one thumb on the Qwik Lock™
stud, which protrudes through the
integrated Filter plate, lift up on the
Filter tabs while pushing down on the
stud.
3. This action will cause the Filter to
release from the Filter cage. Slide
Filter off cage.
Filter Installation:
1. Carefully slide the Qwik Lock™ Filter
over the Filter cage and press down
on the outside edge of the Filter until
the rubber gasket on the bottom of the
Filter seats securely around the base
of the Filter cage and against the lid.
2. Align the small center hole in the top
of the Filter over the Qwik Lock™ stud
on the Filter cage. Press firmly on top
of the Filter near the stud to allow the
Filter to snap over the ball on the end
of the stud. The Filter is now attached.
Lid
Filter
Cage
Qwik
Lock
Stud
Filter
Tabs (2)
Integrated Filter
Plate with Center
Hole
PUSH
DOWN
PULL
UP
Rubber
Gasket at
Bottom of
Filter
(cutaway
view)
NOTE: Failure to properly seat the
bottom gasket could result in debris
bypassing the Filter.
WARNING: Do not operate
without Filter cage and float, as they
prevent liquid from entering the
impeller and damaging the motor.
!
FILTER REMOVAL & INSTALLATION
SP6863-1 Workshop 6 9 GALLON:SP6439-3_ES.qxd 8/19/13 2:09 PM Page 5
9
OPERATION (continued)
Choosing the Correct Filter
There are a variety of Filters available for
WORKSHOP®Wet/Dry Vacuums.
The Filters you choose should depend
upon the task you are performing.
Not all available Filters are included with
each model, but they may be purchased
from retailers carrying WORKSHOP
Wet/Dry Vacuums or from
www.WORKSHOPvacs.com.
The available Filters include:
1. Pleated Paper Cartridge Filters
WARNING: To reduce the risk of
damage to the Vacuum, do not run
motor with float in raised position.
A cartridge Filter should be used
and positioned correctly during all
vacuuming operations to avoid
debris leaks and possible damage
to the vacuum motor.
!
2. Wet Application Cartridge Filter
a. The available Pleated Paper
Cartridge Filters include catalog
numbers WS21200F (Everyday Dirt),
WS22200F (Fine Dust), and
WS23200F (HEPA Media).
b.Each of these Pleated Paper
Cartridge Filters are intended for
cleaning up dry debris, however, a
small amount of liquid can be picked
up without damaging the Filter. When
maintained properly, small amounts
of liquid will not cause damage to the
Filter. When picking up larger
amounts of liquid, the Pleated Paper
Cartridge Filter will become
saturated, misting may appear in the
vacuum’s exhaust, and the Filter may
be damaged. After using the Vac to
pick up small amounts of liquid, the
Pleated Paper Cartridge Filter must
be dried to avoid mildew and
damage.
c. If you are using your vacuum to pick up
very fine dust, it will be necessary for
you to empty the drum and clean the
Filter at more frequent intervals to
maintain peak vacuum performance.
d.See “Filter Removal and Installation”
section for directions on how to
change the Pleated Paper Cartridge
Filter.
a. The available Wet Application
Cartridge Filter is catalog number
WS24200F.
b.The Wet Application Cartridge Filter
is intended for cleaning up liquids
and wet debris only. It is NOT to be
used for any dry debris.
c. To maintain Filter performance, rinse
thoroughly with water after each use.
d.See “Filter Removal and Installation”
section for directions on how to
change the Wet Application
Cartridge Filter.
3. Dust Collection Bags
a. The available Dust Collection Bag is
catalog number WS32090F.
b.The Dust Collection Bag is intended
for cleaning up dry debris ONLY.
c. If the debris being picked up has any
moisture, the bag will absorb the
moisture and may deteriorate very
quickly, making the bag non-
functional.
d.If you are using your vacuum to pick
up fine dust, the Dust Collection Bag
will make cleanup easier.
Note: Dust Collection Bag MUST be
used in conjunction with a Pleated
Paper Cartridge Filter.
e. Directions for Installation and
Removal of Dust Collection Bags are
printed on the bags.
SP6863-1 Workshop 6 9 GALLON:SP6439-3_ES.qxd 8/19/13 2:09 PM Page 9


Product specificaties

Merk: Workshop
Categorie: Stofzuiger
Model: WS0900VA

Heb je hulp nodig?

Als je hulp nodig hebt met Workshop WS0900VA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Stofzuiger Workshop

Handleiding Stofzuiger

Nieuwste handleidingen voor Stofzuiger