Winix A230 Handleiding

Winix Luchtreiniger A230

Lees hieronder de 📖 handleiding in het Nederlandse voor Winix A230 (2 pagina's) in de categorie Luchtreiniger. Deze handleiding was nuttig voor 108 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

A231 / A 230

WHERE TO USE

MODEL PART DIAGRAM

12~18 in

Allow 12 ~ 18 in. of space between TVs, radios, and other electronics

Electromagnetic interference from certain electronics may cause

product malfunction.

Place indoors away from direct sunlight

Direct exposure may cause product malfunction or failure.

Only place on hard, flat surfaces

Flimsy or slanted surfaces may result in abnormal noise and vibrations.

Allow 12 ~ 18 in. from walls

For maximum air flow.

01. Filter Replacement Indicator

LED light indicates when it is time to change the filter.

02. Filter Reset Button

After replacing the 360º All-in-One True HEPA Filter, use a small object such as a paper clip, to press and hold the

Filter Reset Button for at least 5 seconds until the Filter Replacement Indicator turns off.

03. Auto Mode Button

The unit will default to Auto with PlasmaWave® enabled when first powered on.

•Auto Mode automatically adjusts fan speeds according to your indoor air quality. The fan speed will adjust

to low when air quality is good, medium when fair, and to high when poor.

CONTROL PANEL

04. Air Quality Indicator

Color coded LED light indicates one of three levels of Air Quality:

Red (poor), Amber (fair), and Blue (good).

05. Sleep Mode Button

When Sleep Mode is activated, the Air Quality Indicator LED light is disabled.

•Fan speed will automatically set to minimum speed (lower than 'Low') which will be nearly silent.

•When Sleep Mode is active, PlasmaWave® will be disabled, but it can be turned back on.

06. PlasmaWave

Button

Enables or disables PlasmaWave®

"When the unit is running, you may hear a chirping or buzzing sound. The sound is from large particles passing

through PlasmaWave®, it is normal and does not signify product failure."

Press the PlasmaWave® Technology button when the unit is on to enable or disable this feature.

07. Fan Speed Indicator Buttons

Indicates the current fan speed.

•Use the Fan Speed arrow buttons to set the desired fan speed. Fan speeds cycle over in this sequence:

Auto, Low, Medium, High, Auto.

Low Medium High

08. Power Button

Turns the unit on or off. During the first 30 seconds of power, the Air Quality Indicator will cycle through

Blue, Amber and Red colors.

•Odor Sensor takes approximately 4 minutes to detect the air quality in the environment before normal

operation begins.

When to Replace Filters

Filter Indicator L i ght When to ser vice When to replace

360º All-in-One

True HEPA Filter

Clean once every 14 days Lasts Approx. 12 months

•When the Check Filter indicator LED is on, it is time to replace the All-in-One True HEPA Filter.

•Intervals between filter replacement may vary depending on environment.

MAINTENANCE

Activated Carbon Filter

Fine Mesh Pre-Filter

True HEPA Filter

PlasmaWave

4-STAGE AIR PURIFICATION

01. Fine Mesh Pre-Filter

Designed to catch larger airborne particles found

indoors.

02. True HEPA Filter

Captures 99.97%* of airborne allergens including; pollen,

mold spores, dust, pet dander, microbes, and smoke

(*Particles as small as 0.3 microns in size).

03. Activated Carbon Filter

Reduces VOCs and household odors from cooking,

pets, and smoke.

04. PlasmaWave

PlamaWave creates Hydroxyls which can help to

reduce the presence of airborne Bacteria, Viruses*

(*Based on independent laboratory test conducted on

Influenza A Virus H3N2, E. coli, Pseudomonas aeruginosa,

Staphylococcus aureus, Salmonella typhimurium).

INITIAL OPERATION

1. Turn the product upside down.

2. Grab the handle at the bottom of the product, turn

counter-clockwise, and pull out the filter cover.

3. Remove the protective vinyl from the filter

installed inside the product.

4. Install the filter top side down into the bottom of unit

until it is fully inserted. The top of the filter shows the

opening and the bottom of the filter is solid.

5. After installing the filter, turn the handle clockwise

to close the filter cover.

6. Return the product to an upright position and

resume normal operation.

1712-0110-00

FILTER

After replacing a filter,

press the Filter Reset Button

for at least 5 seconds.

REPLACING FILTERS

CLEANING CARE

Cleaning the Filters:

Clean with a vacuum or a soft brush.

•Only clean the Pre-Filter.

•This filter be washed.CAN NOT

•Intervals between filter cleaning may vary

depending on the air quality.

N O T I C E

Do not use benzene, alcohol, or other volatile fluids,

which may cause damage or discoloration.

Cleaning the Exterior & Interior:

Wipe with a soft damp cloth using room temperature

water. Afterwards, wipe it down with a clean dry cloth.

After turning the product upside down, remove the filter

cover and clean the interior with a vacuum cleaner.

•For optimal performance, clean every 14 days.

N O T I C E

•When cleaning the unit, always unplug the power cord

first and then wait until the unit has cooled down.

•Never disassemble, repair, or modify this unit yourself.

•Do not use flammable sprays or liquid detergents.

•Do not allow children to clean or maintain the unit.

•Before cleaning or maintaining, ensure unit is unplugged.

U Man lser ua

• The product warranty is printed on the back of this guide.

• This product is manufactured for use only in USA / CA.

• This product is suitable for 120 V only.

A231 / A230Model

Use & Care

Guide

• Dedicated Call Center: ☎ (877) 699-4649

• Website: www.winixamerica.com

Contact Winix for

product related inquiries

and customer service

AIR PURIFIER

2610-0262-00 Rev.02

To expedite service, please specify the model name and number, the nature of the problem,

your contact information, and your address.

UNIT SPECIFICATIONS

SAFETY INSTRUCTIONS

Thank you for purchasing a Winix air purifier. This product is for household use only.

•Do not repair or modify the unit. All repairs should be

completed by a qualified technician.

•The plug for this unit is polarized with one blade wider

than the other. Do not force the plug into an electrical

outlet. Do not alter the plug in any way. If the plug does

not fit into the outlet, reverse the plug. If it still does

not fit, contact a qualified technician to install a proper

outlet.

•Do not use if the power cord or plug is damaged or the

connection to the wall outlet is loose.

•Use AC 120 V only.

•Do not damage, break, forcefully bend, pull, twist, bundle,

coat, pinch, or place heavy objects on the power cord.

•Periodically remove dust from the power plug.

This will reduce the risk of shock due to humidity build up.

•Remove the power plug from the outlet before cleaning

the unit. When removing the power plug, grasp by

holding the plug itself, never hold by the cord.

•If the power plug is damaged, it must be replaced by

the manufacturer or a qualified technician.

•Remove the power plug from the outlet when not in use.

•Do not handle the power plug with wet hands.

•Do not operate the unit when using indoor smoke-

generating insecticides.

•Do not clean unit with benzene or paint thinner.

Do not spray insecticides on the unit.

•Do not use the unit where it is humid or where the unit

may become wet, such as the bathroom.

•Do not insert fingers or foreign objects into air intake or

outlet.

•Do not use the unit near flammable gases. Do not use

near cigarettes, incense, or other spark-creating items.

•Unit will not remove carbon monoxide emitted from

heating appliances or other sources.

IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER

WARNING: Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire.

Model Nam e A231 / A230

Power Voltage AC 120 V / 60 Hz

Power Rate 55W

Ver ified Room S ize 230sq.ft.

Dimensions 9.5 in(W) x 9.5 in(D) x 14.6 in(H)

Wei ght 6.75lbs

Replacement F i lter FILTER O/SKU: 1712-0110-00

The exterior, design, and product specifications may be changed without prior notice to improve product performance.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or on experienced radio / TV technician for help.

This device contains license-exempt transmitter(s) / receiver(s) that comply with Innovation, Science and Economic

Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

•This device may not cause interference.

•This device must accept any interference, including interference that may cause undesired operation of the device.

"In French: Cet appareil contient des émetteurs/récepteurs exemptés de licence et conformes aux normes Innovation,

Science et Economic. RSS(s) sans licence de Développement Canada. Le fonctionnement est soumis aux deux

conditions suivantes:

•cet appareil ne doit pas causer d’interférences nuisibles, et

•cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un fonctionnement

non souhaité."

Before operating this equipment, carefully read and

follow these safety cautions.

Ensure filters are inserted before running unit

Running the unit without filters may shorten the

lifespan of the unit and cause electric shock or injury.

Be sure foreign objects are NOT inserted into the

vents on the unit

Objects can include pins, rods, and coins.

Do not touch any part of the interior of the unit with

wet hands

The high voltage may cause electric shock.

Ensure unit intake and outlet vents do not become blocked

Blockage may lead to increased internal temperatures,

causing product failure and deformation.

Do not use the unit as a step stool or place heavy

objects on it

Personal injury may occur or product failure and

deformation.

When turning the product upside down, install the

filter with care in the direction that the bottom

(blocked) side of the filter is visible from the top

If the filter direction is not installed properly, it may

cause product damage and user injury.

W A R N I N G

Follow these instructions to reduce the risk of serious

injury or death and to reduce risk of damaging the unit.

•If the power cord is damaged, it must be replaced with a

special cord. Assembly available from the manufacturer

or its service agent.

•This appliance is not intended for use by a person (including

children) with reduced physical sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

•Children should be supervised to ensure that they do not

play with the appliance.

•This unit is not intended to be used to preserve

documents or in art conservation.

Do not pull on the power cord when unplugging the

unit.

Do not tie or knot the power cord when unit is in

operation.

If the unit becomes submerged in water, unplug it

and contact customer service.

Do not unplug or move the unit while in operation.

Do not plug additional appliances into the same

outlet or power supply.

Do not touch the plug with wet hands.

Unplug the unit when not in operation for extended

periods of time.

Do not place around heating elements.

Do not use around mist or fumes from industrial oil

or around large quantities of metallic dust.

The cord can become damaged by forcefully

bending, pulling, twisting, bundling, pinching or

placing heavy objects on it.

Do not install in any sort of motor or transport

vehicle (trucks, boats, ships, etc.).

Do not place in an area with excessive amounts of

noxious gases.

Do not place near any flammable materials

(aerosols, fuel, gases, etc.).

Do not have the unit facing into wind or drafts.

Do not place below any electrical outlet.

Do not place in excessively humid areas where the

unit may become wet.

To reduce the risk of fire or electric shock,

do not use this fan with any solid-state speed

control device.

Do not place unit closer than 12 inches from the

wall during operation. It may cause condensation

on the wall and the surrounding area.

SAFETY AND CAUTIONS

PRODUCT WARRANTY

The terms of the warranty are as follows.

1. This product is manufactured under stringent

quality control and inspections.

2. The warranty will be voided if product failure is a

result of negligence or misuse by the consumer.

3. A proof of purchase must be presented upon

claiming a Product Warranty.

4. Store the proof of purchase in a safe place or

upload your proof of purchase.

5. This warranty is valid only in the USA and Canada.

* for more information visit

https://winixamerica.com/terms-and-conditions/

Product Name Air Purifier

Model Nam e A231 / A230

Purchase D ate

War ranty Per iod Two (2) Years

Place of Pur chas e

tel.

Custom er

Address

Name

Tel.

The unit does not turn on at all

•Is the plug securely attached to the outlet?

-Make sure the outlet has power going to it and ensure

the plug is secured.

•Is there a power outage?

-Check to see if other lights and electrical equipment

are working and try again.

The unit doesn’t work in Auto Mode

•Has Auto Mode been selected?

-Press the Fan Speed button until Auto Mode is

selected.

•Is the sensor blocked or clogged?

-Wipe Odor Sensor with wet cloth, then dry.

It vibrates and makes a lot of noise

•Is it running on a slanted or uneven surface?

-Move the unit to a hard, flat, even area.

The power plug and outlet feel hot

•Is the plug securely plugged in?

-Make sure the plug is properly plugged into the outlet.

There is a strange smell

•Is it being used in a place with a lot of smoke, dust, or

odors?

-Clean the air intakes on either side and clean the

Pre-Filter.

-Replace the 360º All-in-One True HEPA Filter.

The fan strength is weak. The unit is not purifying the air

•Is the Check Filter Indicator light on?

-Change the filters as required.

The display panel is dim

•Is the Light Sensor blocked by debris?

-When Auto Mode is on, Sleep Mode is automatically activated

when the Light Sensor detects that the room is dark.

FREQUENTLY ASKED QUESTIONS

The energy efficiency of this ENERGY STAR

certified model is measured based on a ratio

between the model’s CADR for smoke and the

electrical energy it consumes, or CADR/Watt.

IMPORTANT PRECAUTIONS FOR USING YOUR AIR PURIFIER

•Do not block the intake or outlet vents.

•Do not use near hot objects, such as a stove.

•Do not use where the unit may come into contact with

steam.

•Do not use the unit on its side.

•Keep away from products that generate oily residue,

such as a deep fryer.

•Do not use detergent to clean the unit.

•Do not operate without a filter.

•Do not wash and reuse the True HEPA Filter.

•Hold the handle on the back of the unit to transport.

•Do not hold by the front panel.

•Do not stick any small objects in the air outlet vents

or fan.

Product specificaties

Merk:	Winix
Categorie:	Luchtreiniger
Model:	A230

Heb je hulp nodig?

Als je hulp nodig hebt met Winix A230 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Luchtreiniger Winix

Winix AUS-0850AAPU Handleiding

16 November 2024

Winix U300EU Handleiding

31 Maart 2023

Winix P300UK Handleiding

31 Maart 2023

Winix ZERO+ AUS-1050AZBU Handleiding

18 Juli 2023

Winix P450EU Handleiding

31 Maart 2023

Winix NK305 - Tower Q Handleiding

31 Maart 2023

Winix Zero Pro Handleiding

5 Mei 2023

Winix AZPU373-HWE - Zero plus Wifi Handleiding

31 Maart 2023

Winix Zero Handleiding

23 April 2023

Winix HR900 Handleiding

22 April 2023

Handleiding Luchtreiniger

Nieuwste handleidingen voor Luchtreiniger

Meaco 12L - Low Energy Handleiding

14 September 2024

Mitsubishi MA-83H-W Handleiding

14 December 2024

Vicks EasyCare+ Top Fill Handleiding

10 December 2024

Sôlt GGSPA360W Handleiding

8 December 2024

Sôlt GGSPA500W Handleiding

8 December 2024

Sôlt GGSPA600W Handleiding

8 December 2024

Sôlt GGSPA200W Handleiding

8 December 2024

Rikon 61-200 Handleiding

4 December 2024

Shark NeverChange5 HP150 Handleiding

1 December 2024

Sharp FU-888SV Handleiding

1 December 2024