Whirlpool XHPC155XW Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool XHPC155XW (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 75 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
15.5" PEDESTAL INSTALLATION INSTRUCTIONS
For use only with front load washers and dryers
INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL DE 15,5"
Pour utilisation avec les produits suivants seulement
laveuses et sécheuses à chargement par l’avant
W10347252B
W10348602B - SP
Table of Contents Table des matières
PEDESTAL SAFETY ......................................................1
INSTALLATION REQUIREMENTS ................................2
Location Requirements .........................................2
Tools and Parts .......................................................2
UNPACKING THE PEDESTAL ......................................3
BEFORE INSTALLING THE PEDESTAL .......................3
INSTALLING THE PEDESTAL .......................................4
COMPLETE THE INSTALLATION .................................7
SÉCURITÉ DU PIÉDESTAL ..........................................9
EXIGENCES D’INSTALLATION ....................................9
xigences d’emplacement ....................................9E
Outillage et pièces .................................................9
INSTRUCTIONS D’INSTALLATION ............................10
AVANT L’INSTALLATION DU PIÉDESTAL .................11
INSTALLATION DU PIÉDESTAL .................................12
ACHEVER LINSTALLATION .......................................15
INSTALLATION NOTES
Date of purchase: _________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
NOTES CONCERNANT L’INSTALLATION
Date d’achat : _____________________________________
Date d’installation : ________________________________
Installateur : ______________________________________
Numéro de modèle : ________________________________
Numéro de série : __________________________________
PEDESTAL SAFETY
Para una versión de estas instrucciones en español, visite www.whirlpool.com
2
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools Needed:
Utility knife 1/4" hex-head ratchet
or open-end wrench
Level 9/16" open-end wrench
Pliers or slip-joint pliers Bucket
INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
NOTE: If the washer/dryer and pedestal assembly are located in
a garage, 3 (76 mm) must be added under the pedestal so that "
the washer/dryer is 18" (458 mm) above the garage oor.
Towel Sponge
Parts Supplied:
Four #12 x 3/4" hex-head Drawer divider
sheet metal screws
Additional Items Needed:
1/4" nut driver 5/16 hex-head ratchet "
or nut driver
3
NOTE: If the washer is to be transported, call your local service
center. To avoid suspension and structural damage, your
washer must be properly set up for relocation by a certied
technician.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord.
3. Slowly loosen the ll hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove the “HOT” and “COLD” ll hoses from the back of
the washer. Drain the water from the hoses into a bucket.
5. Remove the drain hose from the standpipe or laundry tub and
drain any water remaining in the hose into a bucket.
6. Pull the washer away from the wall so that you will have
enough space for the installation.
1. Empty pedestal drawer
UNPACKING THE PEDESTAL
Preparing the pedestal for installation
Open the pedestal drawer as far as possible and remove the
contents. The package contains four #12 x 3/4" hex-head
sheet metal screws and a drawer divider.
IMPORTANT: Set the pedestal box aside for use during
installation.
Hex-head screw
Drawer slide
3. Remove pedestal drawer
Using a 1/4" nut driver, remove the hex-head screws from both
drawer slides and save screws. Remove the drawer from the
slides and set aside. Push the slides back into the pedestal.
BEFORE INSTALLING PEDESTAL
IMPORTANT: If your washer and dryer are already installed,
they must be uninstalled.
Uninstalling your washer
To avoid possible damage to the washer, the transport bolts on
the back of the washer must be in place before installing the
pedestal. For more information on transport bolts see, “Remove
Transport System” in washer Use and Care Guide.
The four spacer pads are installed on the top of the pedestal.
These pads reduce vibration between the pedestal and the
washer/dryer.
NOTE: If your washer/dryer has feet installed, remove them.
Spacer pads
2. Locate spacer pads


Product specificaties

Merk: Whirlpool
Categorie: Niet gecategoriseerd
Model: XHPC155XW

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool XHPC155XW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Whirlpool

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd