Whirlpool WP 76/1 LD Handleiding

Whirlpool Vaatwasser WP 76/1 LD

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool WP 76/1 LD (8 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Whirlpool is a registered trademark of Whirlpool USA 5019 396 01119
1
GB WP 76 LD
Before using the dishwasher, read the
installation and maintenance instructions carefully!
1) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different
loads, options, different sensor settings (only with sensor programmes), different water supply temperatures, as well as water
hardness and power supply voltage.
2) Reference programme for energy label in compliance with EN 50242. - Important information for Test Laboratories: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
1. OVERVIEW
On button
Off button
Delayed start button
Press the button repeatedly to delay the
start of the programme by 3, 6 or 9 hours.
Then press the START button. The
dishwasher will start at the set time.
Detergent setting upon initial use and when using a different type of
detergent
1. Select the third programme in the relative table.
2. Press the START button for approx. 7 sec. to change the display.
3. Using the START button, select the desired detergent:
“3h” = 2in1,6h” = 3in1, “9h= other combined action detergents
(in this way, the rinse aid and/or salt indicator is deactivated). All 3
LEDs light up = Powder detergent (factory setting).
4. Switch the appliance off and then switch it on again. The selected
detergent type will be indicated on the display by the
corresponding LEDs for approx. 3 seconds.
Programme selection button
Press the button repeatedly until the desired programme
indicator lights up.
Start button
Switches “on” when the dishwasher is operating.
Flashes when a fault occurs. Switches off at the end of
the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected
programme and options are cancelled. Main failure
displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions
are given in chapter 5 “What to do if...”.
Rinse aid level indicator and salt level indicator
These indicator lamps light up when rinse aid or salt
need to be added. Add just before starting a wash
programme.
Table 1.1.
Programme chart Detergent
dispenser Consumption 1)
PProgrammes Available
options Loading instructions large small Litres kWh Minutes
1 Sensor Intensive 60-70°C
Automatic programme
recommended for heavily
soiled crockery with dried-on
or burnt food, for example
pans and saucepans.
X X 13-20 1.10-2.00 100-150 ±1)
2 Quickwash 40°C Lightly soiled crockery, with
no dried-on food. X 10.0 0.65 30 ± 1)
3Eco 2) 50°C Normally soiled crockery. X X 12.0 1.05 165 ± 1)
4 Intensive 70°C
Recommended programme
for heavily soiled crockery,
especially suitable for pans and
saucepans.
X X 14.0 1.55 155 ± 1)
5 Power Clean 70°C
Recommended programme for
heavily soiled crockery, especially
suitable for pans and saucepans.
Intensive wash with additional
water jets.
X X 16.0 1.80 220 ± 1)
2
2. QUICK REFERENCE GUIDE
Detailed instructions are given in the following pages, see also chapter “5. What to do if...”
1. Switch on the
appliance
Open the dishwasher door.
Press the ON button.
2. Select a programme Press the button or to bring up the desired programme on the display.
Select options, if available.
3. Select the type of
detergent
The detergent selection procedure varies depending on the dishwasher model.
Chapter “1. Overview provides instructions for selecting detergent type.
4. Fill in the detergent 4a. Powder/gel/tabs
Fill the detergent dispenser compartments in
accordance with the wash programme selected.
Large compartment A for every wash cycle, additional
small compartment B for programmes with pre-wash
(see table 1.1.).
4b. Combined action detergents (2 in 1/3 in 1/... etc.)
Place the detergent in compartment A or in the cutlery
basket, as per the manufacturer's recommendations.
5. Check the rinse aid
level
6. Check the salt level Depending on the model:
7. Load the racks
Make sure that the spray arms can turn freely and are not impeded by crockery
or cutlery in the racks.
Detailed instructions on loading the racks are given in chapter “3. How to use
the appliance”, under “How to load the racks”.
8. Start the appliance Press the START button.
9. Turn on the water
tap and close the
dishwasher door
When the door is closed the dishwasher
starts automatically.
Wash cycle
If the appliance is switched off during a
wash cycle, when switched on again it will
resume the cycle from where it was
interrupted. Care must be taken when
opening the door, as steam will escape!
10.End of programme At the end of the programme an acoustic signal will sound.
The START indicator lamp switches off.
11.Open the door,
switch off the
appliance
Press the OFF button. All the indicator lamps switch off.
12. Turn off the water
tap, unload the racks
Unload the appliance, starting from the lower rack in order to avoid any
residual drips of water falling onto crockery below.
AC
B
Visual indicator in dispenser C
dark sufficient rinse aid present,
clear add rinse aid (approx. 100 ml).
The indicator lamp on the control panel lights up when rinse aid
needs to be added. Not all models are equipped with such an
indicator.
window in salt reservoir cap on bottom of appliance inside
orange when sufficient salt is present,
clear when salt needs to be added.
The indicator lamp on the control panel lights up when salt needs
to be added. Even once salt has been added, the indicator lamp
only switches off after several wash cycles!
Change the programme in progress:
- Press the START button for
about 2 sec., until the START
indicator lamp switches off.
- Close the door.
- (Water drains for up to 60 seconds).
- Open the door.
- Select a new programme.
- Press the START button.
3
3. HOW TO USE THE APPLIANCE
PROGRAMME SELECTION
Press the button or to bring up the desired programme on the display. The appliance must be switched
on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate
programmes and relative available options are detailed in table 1.1 on page 1.
Programme times stated in the table were obtained under normal conditions and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes
as a result of the appliance's automatic calibration system.
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme. Only use detergents
specially recommended for dishwashers, observing the manufacturer's recommended dosage.
Observe the manufacturer's safety warnings!
Open the detergent dispenser compartments by pushing the left lever (lever 1) of the dispenser.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
pour the entire recommended dosage into compartment A.
Programmes with pre-wash:
pour 2/3 of the recommended dosage into the large compartment
A and 1/3 into the small compartment B.
Dishwasher tabs should be placed, according to the
manufacturer's recommendations, in compartment A or in the
cutlery basket.
If the “Half load” option is selected, detergent dosage should be
reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Combined action detergents should be placed, according to the
manufacturer's recommendations, in compartment A or in the
cutlery basket.
Firmly press the detergent compartment lid shut after filling.
Detergents with rinse aid incorporated may be effective only with longer programmes. In the
case of shorter programmes, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
The guarantee is not applicable if faults are caused by the use of these products.
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level
Check the visual indicator C on the rinse aid dispenser: dark = su ear = add rinse aid.fficient rinse aid, cl
In the case of appliances with an electric indicator on the
control panel, the rinse aid indicator lamp lights up red
when rinse aid needs to be added.
b. How to fill the rinse aid dispenser
Open the rinse aid dispenser by pressing the right lever
(lever 2) of the dispenser.
Fill the dispenser with rinse aid up to the “max” line
(approx. 100 ml).
Shut the lid again.
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away
any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault
function of the appliance.
Lever 1
Large
compartment A
Small
compartment B
Lever 2Indicator C
max


Product specificaties

Merk: Whirlpool
Categorie: Vaatwasser
Model: WP 76/1 LD

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool WP 76/1 LD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwasser Whirlpool

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser