Whirlpool WIS 9040 PEL Handleiding

Whirlpool Vaatwasser WIS 9040 PEL

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool WIS 9040 PEL (33 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/33

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

PRODUCT DESCRIPTION

1. ON/OFF button

2. PREVIOUS button

3. NEXT button

4. Multizone button

5. Display

6. Multizone indicator lights

7. Eco program indicator light

8. Start Delay indicator light

9. Program number and remaining time indicator

10. Closed water tap indicator light

11. Rinse Aid rell indicator light

12. Salt rell indicator light

13. Tablet Detergent (All-in-one) indicator light

14. Tablet Detergent (All-in-one) button with indicator light

15. Turbo button with indicator light

16. Power Clean® button with indicator light

17. Start Delay button with indicator light

18. START button with indicator light

CONTROL PANEL

0000 000 00000

Service:

1. Upper rack

2. Cutlery rack

3. Foldable aps

4. Upper rack height adjuster

5. Upper spray arm

6. Power Clean support

7. Lower rack

8. Lower spray arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 1811

INSTRUCTION FOR USE

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please register your appliance on:

www.whirlpool.eu/register

FIRST TIME USE

SETTING MENU AND SALT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

SETTING MENU

1. Switch on the appliance by pressing the button.ON/OFF

2. Switch o the appliance by pressing the button.ON/OFF

3. Hold down START button for 5 seconds, until you hear a beep.

4. The display shows the rst available setting (letter „A”), followed by

its value (for example: 3).

5. Press PREVIOUS/NEXT button to scroll the list of the available settin-

gs and to see their value (see the below table), then press START if you

want to change the value of the displayed setting: its value will start

blinking.

6. Use PREVIOUS/NEXT button to change the blinking value of the se-

lected settings, then press START to save the new value: it will stop

blinking.

7. To change another settings repeat steps 5-6.

8. To exit settings menu - press button. ON/OFF

LETTER SETTING VALUES

(Default - in bold)

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”)

1 | 2 | | 4 | 53

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF

RINSE AID”)

1 | 2 | 3 | 4 | 5

Start Program

To set the cycle to show at switch on

of the appliance.

“E”= Eco, “L”= Last cycle run

E | L

Brightness Level

To adjust the brightness

level of the display.

“Lo”=Low, “Hi”= High

Lo | Hi

Sound Level

To adjust the volume of the sounds.

“OF” = sounds o, “Lo” = low volume,

“Hi” = high volume.

OF | Lo | Hi

Light on the Floor

(see OPTIONS AND FUNCTIONS)

“On” = On, “OF” = O

On | OF

Factory Settings

To restore to the factory default all

the values of the settings includ-

ed in the settings menu. After the

activation of this setting (ON), the

machine switches OFF and restores

the factory settings.

“On” = On, “OF” = O

On | OF

NaturalDry

(see “OPTIONS AND FUNCTIONS”)

“On” = On, “OF” = O

On | OF

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL

indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

As soon as this procedure is complete, run a program without loading.

The “Pre-Wash” program alone is not sucient.

Residual saline solution or grains of salt can lead to corrosion, irreparably

damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

Whenever you need to add salt, it is mandatory to complete the pro-

cedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is “3” for average water hardness.

To change, follow instructions in section “SETTING MENU”.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

FIRST TIME USE

RINSE AID AND DETERGENT

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently

preventing scale buildup on heater, contributing also to better cleaning

eciency.

This system regenerates itself with salt, therefore it is required to

rell salt container when empty.

Frequency of regeneration depends on water hardness level setting -

regeneration takes place once per Eco cycles with water hardness 6

level set to . 3

Regeneration process starts in nal rinse and nishes in drying phase,

before cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A

lled when the in the control RINSE AID REFILL indicator light

panel is lit.

1. Open the dispenser by pressing and pulling up the tab on the lid.B

2. Carefully introduce the rinse aid as far as the maximum (110 ml) ref-

erence notch of the lling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth .

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satised with the drying results, you can ad-

just the quantity of rinse aid used.

To change, follow instructions in section “SETTING MENU”.

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is “5”.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set

a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER

Usage of detergent not designed for dishwashers may cause mal-

function or damage to the appliance.

To achieve the best washing and drying results, the combined use

of detergent, rinse aid liquid and rened salt is required.

We recommend using detergents that do not contain phosphates

or chlorine, as these products are harmful to the environment.

Good washing results also depend on the correct amount of detergent

being used.

Exceeding the stated amount does not result in a more eective

wash and increases environmental pollution.

The amount can be adjusted to the soil level. In the case of normally

soiled items, use approximately either 35g (powder detergent)

or 35ml (liquid detergent) and additional tea spoon of detergent

directly inside the tub. If tablets are used, one tablet will be enough.

If the crockery is only lightly soiled or if it has been rinsed with

water before being placed in the dishwasher, reduce the amount

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

powder/gel putted inside the tub.

To open the detergent dispenser press button C. Introduce the

detergent into the dry dispenser D only. Place the amount of

detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity..

Inside the dispenser there are indiD-

cations to help the detergent dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the TABLET

DETERGENT button, because it adjusts the program so that the best

washing and drying results are always achieved.

If you are using a all-in-one detergents, we recommend that you

add salt in any case, especially if the water is hard or very hard

(follow the instructions given on the packaging).

Product specificaties

Merk:	Whirlpool
Categorie:	Vaatwasser
Model:	WIS 9040 PEL
Apparaatplaatsing:	Volledig ingebouwd
Soort bediening:	Touch
Ingebouwd display:	Ja
Gewicht:	35500 g
Breedte:	598 mm
Diepte:	555 mm
Hoogte:	820 mm
Netbelasting:	1900 W
Aantal couverts:	14 couverts
Deurkleur:	Roestvrijstaal
Snoerlengte:	1.3 m
Uitgestelde start timer:	Ja
Startvertraging:	24 uur
Resterende tijd indicatie:	Ja
Duur cyclus:	190 min
Geluidsniveau:	41 dB
Energie-efficiëntieklasse:	C
Gewicht verpakking:	37500 g
Installatie compartiment breedte:	600 mm
Installatie compartiment diepte:	560 mm
Installatie compartiment hoogte:	900 mm
Waterconsumptie per cyclus:	9.5 l
Stroom:	10 A
Installatie compartiment hoogte (min):	820 mm
Geluidsemissieklasse:	B
Aantal wasprogramma's:	10
Energieverbruik per 100 cycli:	75 kWu
Verstelbare voeten:	Ja
Productafmeting:	Volledige grootte (60 cm)
Kleur bedieningspaneel:	Black, Stainless steel
Gebruiksklaar-indicatielampje:	Ja
Waarschuwingssignaal:	Ja
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Glasbescherming:	Ja
Afwasprogramma's:	Eco 45°C, Glass/delicate, Hygiene, Intensive 65°C, Pre-wash, Quick, Self-Clean 65°C
Energieverbruik per cyclus:	0.748 kWu
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.55 m
Bovenste mand verstelbare hoogte:	Ja
Maximale warmwatertoevoertemperatuur:	60 °C
Temperatuur (max):	65 °C
Stroomverbruik (indien uit):	0.5 W
AC-ingangsspanning:	220 - 240 V
Energie-efficiëntieschaal:	A tot G