Whirlpool WIP 4O32 PT Handleiding

Whirlpool Vaatwasser WIP 4O32 PT

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool WIP 4O32 PT (12 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTRUCTION FOR USE

THANK YOU FOR PURCHASING A WHIRLPOOL PRODUCT.

To receive more comprehensive help and support, please register your product at:

www.whirlpool.eu/register

Before using the appliance carefully read Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1.Upper rack

2.Foldable flaps

3.Upper rack height adjuster

4.Upper spray arm

5.PowerClean Supports

6.Lower rack

7.Cutlery basket

8.Lower spray arm

9.Filter Assembly

10.Salt reservoir

11.Detergent and Rinse Aid dispensers

12.Rating plate

13.Control panel

0000 000 00000

Service:

CONTROL PANEL

1. ON/OFF button

2. PREVIOUS button

3. NEXT button

4. Multizone button

5. Display

6. Multizone indicator ligh

7. Eco program indicator light

8. Start Delay indicator light

9. Program number and remaining time indicator

10. Closed water tap indicator light

11. Rinse Aid refill indicator light

12. Salt refill indicator light

13. Tablet Detergent (All-in-one) indicator light

14. Tablet Detergent (All-in-one) button with indicator light

15. Turbo button with indicator light

16. Power Clean button with indicator light

17. Start Delay button with indicator light

18. START button with indicator light

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

FIRST TIME USE

SETTING MENU AND SALT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

SETTING MENU

1. Switch on the appliance by pressing the ON/OFF button.

2. Switch off the appliance by pressing the ON/OFF button.

3. Hold down START button for 5 seconds, until you hear a beep.

4. The display shows the first available setting (letter "A"), followed by

its value (for example: 3).

5. Press PREVIOUS/NEXT to scroll the list of the available settings

and to see their value (see the below table), then press START if

you want to change the value of the displayed setting: its value will

start blinking.

6. Use PREVIOUS/NEXT buttons to change the blinking value of the

selected settings, then press START to save the new value: it will

stop blinking.

7. To change another settings repeat steps 5-6.

8. To exit settings menu - press ON/OFF button.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see

PRODUCT DESCRIPTION) and should be filled when the SALT REFILL

indicator light in the control panel is lit.

1.Remove the lower rack and unscrew

the reservoir cap (anticlockwise).

2.Only the first time you do this: fill the

salt reservoir with water.

3.Position the funnel

(see figure)

and fill

the salt reservoir right up to its edge

(approximately 1 kg); it is not unusual

for a little water to leak out.

4.Remove the funnel and wipe any salt

residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

As soon as this procedure is complete, run a program without loading.

The “Pre-Wash” program alone is not sufficient.

Residual saline solution or grains of salt can lead to corrosion,

irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such

circumstances.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches off.

Only use salt that has been specifically designed for dishwashers.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result.

Whenever you need to add salt, we recommend carrying out the

procedure just before the washing cycle is started.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is “3” for average water hardness.

To change, follow instructions in section “SETTING MENU”.

LETTER SETTING VALUES

(Default - in bold)

Water Hardness Level

(see “Setting the Water Hardness”

and “Water Hardness Table”)

1 | 2 | 3 | 4 | 5

Rinse Aid Level

(see “Adjusting the dosage of Rinse Aid”) 1 | 2 | 3 | 4 | 5

Start Program

To set the cycle to show at switch on of the

appliance.

“E”= Eco, “L”= Last cycle run

E | L

Brightness Level

To adjust the brightness

level of the display.

“Lo”=Low, “Hi”= High

Lo | Hi

Sound Level

To adjust the volume of the sounds.

“OF” = sounds off, “Lo” = low volume,

“Hi” = high volume.

OF | Lo | Hi

Internal Lights

(see “Options and Functions”)

“On” = On, “OF” = Off

On | OF

Factory Settings

To restore to the factory default all the

values of the settings included in the

settings menu. After the activation of this

setting (ON), the machine switches OFF and

restores the factory settings.

“On” = On, “OF” = Off

On | OF

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 17 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

FIRST TIME USE

RINSE AID AND DETERGENT

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be filled when the RINSE AID REFILL indicator light in the control

panel is lit.

1. Open the dispenser

by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml)

reference notch of the filling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

To change, follow instructions in section “SETTING MENU”.

If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW

RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is “4”.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set a

high number (4-5).

FILLING THE DETERGENT DISPENSER

Only use detergent which has been specifically designed for

dishwashers.

To achieve the best washing and drying results, the combined use

of detergent, rinse aid liquid and refined salt is required.

We recommend using detergents that do not contain phosphates

or chlorine, as these products are harmful to the environment.

Good washing results also depend on the correct amount

of detergent being used.

Exceeding the stated amount does not result in a more effective

wash and increases environmental pollution.

The amount can be adjusted to the soil level. In the case of normal-

ly soiled items, use approximately either 35g (powder detergent)

or 35ml (liquid detergent) and additional tea spoon of detergent

directly inside the tub. If tablets are used, one tablet will be enough.

If the crockery is only lightly soiled or if it has been rinsed with

water before being placed in the dishwasher, reduce the amount

of detergent used accordingly (minimum 25 g/ml) e.g. skip the

powder/gel putted inside the tub.

To open the detergent dispenser

press button A. Introduce the

detergent into the dry dispenser B

only. Place the amount of detergent

for pre-washing directly inside the

tub.

1. When measuring out the detergent

refer to the mentioned earlier

information to add the proper

quantity.

Inside the dispenser

there are indications to help the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the

TABLET

DETERGENT

button, because it adjusts the program so that the best

washing and drying results are always achieved.

If you are using a all-in-one detergents, we recommend that you

add salt in any case, especially if the water is hard or very hard

(follow the instructions given on the packaging).

Product specificaties

Merk:	Whirlpool
Categorie:	Vaatwasser
Model:	WIP 4O32 PT
Apparaatplaatsing:	Volledig ingebouwd
Ingebouwd display:	Ja
Gewicht:	35500 g
Breedte:	595 mm
Diepte:	555 mm
Hoogte:	820 mm
Netbelasting:	1900 W
Aantal couverts:	14 couverts
Deurkleur:	Niet van toepassing
Snoerlengte:	1.3 m
Uitgestelde start timer:	Ja
Startvertraging:	24 uur
Resterende tijd indicatie:	Ja
Droogklasse:	A
Duur cyclus:	215 min
Geluidsniveau:	42 dB
Jaarlijks energieverbruik:	238 kWu
Gewicht verpakking:	37500 g
Energie-efficiëntieklasse (oud):	A+++
Installatie compartiment breedte:	600 mm
Installatie compartiment diepte:	570 mm
Waterconsumptie per cyclus:	- l
Stroom:	10 A
Installatie compartiment hoogte (min):	820 mm
Verstelbare voeten:	Ja
Productafmeting:	Volledige grootte (60 cm)
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Energieverbruik per cyclus:	0.833 kWu
Jaarlijks waterverbruik:	2660 l
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.55 m
Bovenste mand verstelbare hoogte:	Ja
Installatie compartiment hoogte (max):	900 mm
Temperatuur (max):	60 °C
Stroomverbruik (indien uit):	0.5 W
AC-ingangsspanning:	220 - 240 V
AC-ingangsfrequentie:	50 Hz