Whirlpool WFE2B19 Handleiding

Whirlpool Vaatwasser WFE2B19

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool WFE2B19 (8 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please

www.whirlpool.eu/register

You can download the Safety Instructions and the Use

and Care Guide, by visiting our website

http://docs.whirlpool.eu and following the Instructions

on the back of this booklet.

Before using the appliance carefully read Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack

2. Foldable flaps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

0000 000 00000

Service:

CONTROL PANEL

1. On-Off/Reset button with indicator light

2. Program selection button with indicator light

3. Half Load button with indicator

4. Salt refill indicator light

5. Rinse Aid refill indicator light

6. Program indicator lights

7. Delay indicator light

8. Delay button with indicator light

9. Tablet (Tab) button with indicator light

10. Start/Pause button with indicator light / Drain out

1 2 43 5 6 7

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see

PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL

indicator light in the control panel is lit.

1.Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2.Position the funnel

(see figure)

and fill the salt

reservoir right up to its edge (approximately 1 kg);

it is not unusual for a little water to leak out.

3.Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, we recommend carrying out the

procedure before the washing cycle is started.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for average (3) water hardness.

1. Switch on the appliance by pressing the

ON/OFF

button.

2. Switch off the appliance by pressing the

ON/OFF

button.

3. Hold down button

START/PAUSE

for 5 seconds, until you hear a

beep.

4. Switch on the appliance by pressing the

ON/OFF

button.

5. The program indicator light of the current set level flashes.

6. Press button

to select the desired hardness level

(see Water

Hardness Table).

7. Switch off the appliance by pressing the

ON/OFF

button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches off.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be filled when the RINSE AID REFILL indicator light in the control

panel is lit.

1. Open the dispenser

by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml)

reference notch of the filling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button

START/PAUSE

three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The program indicator light of the current set level flashes.

• Press button P to select the level of rinse aid quantity to be

supplied.

• Switch it off using the ON/OFF button

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 4 levels can be set according to the dishwasher model.

The factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

high number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser

use the opening device A. Introduce

the detergent into the dry dispenser

B only. Place the amount of

detergent for pre-washing directly

inside the tub.

1.When measuring out the detergent

refer to the (see PROGRAMS TABLE) to

add the proper quantity.

Compartment

comprises a level

showing the maximum quantity of liquid or powder detergent that

can be added to each cycle.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the

TABLET

button, because it adjusts the program so that the best washing and

drying results are always achieved.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 17 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 50242.

*) Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Program

Drying

Available options *)

Detergent

container Duration of

wash program

(h:min)**)

Water con-

sumption

(litres/cycle)

Energy con-

sumption

(kWh/cycle)

Tub B

1. Eco 50° 3:10 11 1,04

2. Intensive 65° 2:30 16,5 1,65

3. Normal 55° - 2:00 16 1,35

4. Rapid 30’ 50° - - 0:30 8,5 0,50

5. Pre-Wash - - - - 0:10 4 0,01

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

ECO

Normally soiled crockery. Standard program, the most efficient in terms

of its combined energy and water consumption.

INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

NORMAL

Normally soiled crockery. Everyday cycle, that ensures optimal cleaning

performance in shorter time.

RAPID 30’

Program to be used for lightly-soiled dishes with no dried food

residues. (Ideal for 2 place settings).

PRE-WASH

Crockery to be washed later. No detergent to be used with this

program.

Notes:

Optimum performance levels when using the “Rapid” program can be

achieved by observing the maximum amounts of specified place

settings.

To reduce consumption even further, only run the dishwasher

when it is full.

Product specificaties

Merk:	Whirlpool
Categorie:	Vaatwasser
Model:	WFE2B19
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Knoppen
Ingebouwd display:	Nee
Gewicht:	47000 g
Breedte:	600 mm
Diepte:	600 mm
Hoogte:	850 mm
Netbelasting:	1900 W
Aantal couverts:	13 couverts
Droogsysteem:	Statisch
Deurkleur:	Wit
Snoerlengte:	1.3 m
Uitgestelde start timer:	Ja
Startvertraging:	8 uur
Droogklasse:	A
Duur cyclus:	190 min
Geluidsniveau:	49 dB
Jaarlijks energieverbruik:	295 kWu
Gewicht verpakking:	49000 g
Breedte verpakking:	650 mm
Diepte verpakking:	675 mm
Hoogte verpakking:	910 mm
Energie-efficiëntieklasse (oud):	A+
Installatie compartiment breedte:	600 mm
Installatie compartiment diepte:	570 mm
Waterconsumptie per cyclus:	11 l
Stroom:	10 A
Installatie compartiment hoogte (min):	820 mm
Aantal wasprogramma's:	5
Productafmeting:	Volledige grootte (60 cm)
Kleur bedieningspaneel:	Wit
Bestek compartiment type:	Mand
Kuip materiaal:	Roestvrijstaal
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Multitab optie:	Ja
Bescherming tegen overstromen:	Ja
Half-geladen:	Ja
Afwasprogramma's:	Eco, Intensive, Pre-wash, Quick
Energieverbruik per cyclus:	1.04 kWu
Jaarlijks waterverbruik:	3080 l
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.55 m
Bovenste mand verstelbare hoogte:	Ja
Installatie compartiment hoogte (max):	900 mm
Stroomverbruik (indien uit):	0.5 W
AC-ingangsspanning:	220 - 230 V
AC-ingangsfrequentie:	50 Hz