Vitek VT-8P125 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Vitek VT-8P125 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
VITEK
VITEK
FEATURES
• Provides 8 - 10/100Base-TX PoE ports & 2 10/100Base-
TX Ethernet Ports
• 125 Watt PoE Power Budget
• Conforms to IEEE802.3, IEEE 802.3u, IEEE802.3af,
IEEE802.3at
• High back-plane bandwidth 1.8Gbps
• IEEE802.3x Flow control
• Surge protection for power port and data ports
• EMI standards complies with FCC, CE class B
VT-8P125
8 Port 125 Watt Compact
PoE Switch
2
Product Layout
Installation
Package Contents:
Extend Function:
Enables 200 meter transmission at 10mbps. Power input port
ON F/ OF DC48V
POE Ethernet Port Up-link Ethernet Port
PWR
Link Active/
Function
Function E thernet Po E Switch
10
Notice
Please restart device after enabling/disabling the Extend function.
1) Please turn off the PoE Switch & all ethernet devices power before installation to avoid damage,
2) Use network cable to connect PoE IP cameras to ports 1~ 8 respectively
3) Use a network cable to connect equipment via up link port and NVR or computer
4) Connect power adapter
5) Check if the installation is correct and equipment is in good condition and the connection is stable
6) Ensure the Ethernet equipment with power is working properly.
Installation Steps:
8 Ports PoE Et hernet Swit ch
Cat5 5e 6
Cable
Monitor
NVR
PoE PTZ Camera
PoE IP Camera
PoE Dome C amera
PoE IP Camera
power
Application
10 ports PoE Ethernet Switch 1pcs
Power adaptor 1pcs
Ac power cable 1pcs
Accessory 1pcs
User manual 1pcs
3
- Please follow these steps if the equipment has trouble
- Make sure the equipment is installed according to the installation guide
- Configure RJ45 cable order meets EIA TIA568A or 568B standard
- Every PoE port can provide maximum power of uo to 30W
- Please contact your vendor if trouble still exists
Troubleshooting
Specifications
Instruments to be used wire crimper network tester Wire sequence of RJ45 plug should
conform with EIA TIA568A or 568B
1 Please remove 2cm long the insulating layer and bare 8 pairs UTP cable
2 Separate the 8 pairs UTP cable and straighten them
3 Line up the 8 pieces of cables per EIA TIA 568A or 568B
4 Cut off the cables to leave 1 5cm bare wire
5 Plug 8 cables into RJ45 plug make sure each cable is in each pin
6 Use the wire crimper to crimp it
7 Repeat above 9 steps to make the another end
8 Use network tester to test the cable if t works
Pin Color
White reenG
Green
Blue
White Orange
White lueB
White Brown
Orange
Brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
White Green
Green
Blue
White Orange
White Blue
White Brown
Orange
Brown
EIA TIA 568A EIA TIA 568B
1818
Wiring
Detailed Specifications
Ports
PoE Standa rd
PoE Pin assi gnme nt
LED Indi cato rs
Switc hi ng ca pac ity
MAC addre ss table
Tra ffic c ontrol
Therm al metho ds
Input v oltage
Powe r consumptio n
Ope rating te mpera ture
8 - 10/100B ase -TX PoE Po rts / 2 - 10/100Ba se- TX ports
IEE802.3a f, IEEE 802.3a t, pe r port 30W(MA X) / Total 130W
V+ (RJ45 Pin 4, 5), V- (R J45 Pi n 7, 8).
PWR, Po E, Link/Act LED
2.0G
4K
IEEE 802. 3x ful l-dupl ex flo w co ntro l
Fanles s
100V240V AC90/60H z ( fo r power ada pter) / 48VDC (for Po E s wi tc h)
130W (125W fo r P oE)
32º~ 104ºF (0º~40ºC ) / 20~ 85% RH


Product specificaties

Merk: Vitek
Categorie: Niet gecategoriseerd
Model: VT-8P125

Heb je hulp nodig?

Als je hulp nodig hebt met Vitek VT-8P125 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Vitek

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024