Vemer Humi Handleiding

Vemer Luchtbevochtiger Humi

Lees hieronder de 📖 handleiding in het Nederlandse voor Vemer Humi (3 pagina's) in de categorie Luchtbevochtiger. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

1 6

Vemer S.p.A.

I - 32032 Feltre (BL) • Via Camp Lonc, 16

Tel +39 0439 80638 • Fax +39 0439 80619

e-mail: info@vemer.it - web site: www.vemer.it

MKIS00916-010-EN Mod. HUMI

Electronic flush-mounting humidistats for humidity regulation which performs

actions of type 1B and intended for operating in environments with Pollution

Degree 2 and Overvoltage Category III (EN60730-1).

Codel Model Description

VE379400 Humi Electronic flush-mounting humidistat 230V

SAFETY WARNINGS

During product installation and operation it is necessary to observe the

following instructions:

1) The device must be installed by a qualified person, in strict compliance with the

connection diagrams.

2) Do not power or connect the device if any part of it is damaged.

3) After installation, inaccessibility to the connection terminals without appropriate

tools must be guaranteed.

4) The device must be installed and activated in compliance with current electric

systems standards.

5) Before accessing the connection terminals, verify that the leads are not live.

6) In the electrical system of the building where the instrument must be installed,

a protection device from the overcurrents must be present.

TECHNICAL SPECIFICATIONS

• Power supply:

– 230Vac (-15% ÷ +10%) 50/60Hz

– absorption: 4VA (0.5W)

• Installation on 3 modules box (503 type)

• Terminals:

– 3 terminals for 1.5 mm2 cables for bistable output relay 5A / 250 Vac

– 2 terminals for 1.5 mm2 cables for power supply

• Output: bistable relay 5 (3) A / 250Vac

• Minimum time between a switching and the next one: 1 minute

• Regulation type: on/off with fixed differential of ± 2.5% RH

• Regulation range: 30% ÷ 90% RH

• 2-position selector switch: always off, automatic

• Operating humidity: 20÷90% non condensing

• Protection degree: IP40

• Insulation: reinforced among accessible parts (frontal) and all other terminals

• Mechanical locks on the knob to limit the setpoint

The humidistat signals the error probe condition by blinking the led 2 times

per second.

In this case the regulation is inhibited and the relay contact remains

between terminals 2 and 3. Contact the Technical Service.

REFERENCE STANDARDS

Compliance with Community Directives

2014/35/EU (LVD)

2014/30/EU (EMCD)

is declared with reference to the following harmonized standards:

EN 60730-1 • EN 60730-2-13

• Install the humidistat at a height of about 1.5 m above the floor, away from

direct sunlight, away from doors, windows, heat sources, locations with

excess or total lack of ventilation.

• The device is sold already mounted with

anthracite colour. To transform it in the

white version, remove the knob and the

cover, acting on the hooks placed on

the upper and lower side of the device

and mount the cover and the white knob

included in the package.

• Make the connections by respecting the

diagrams described in this manual.

• Use the selector switch to turn on or off the humidistat:

- position 0: humidistat off, no regulation

- position |: humidistat switched on, active regulation for detected

humidity values exceeding the set value

• Use the knob to set the desired

humidity level.

It’s possible to set values between

30% RH and 90% RH.

When the humidity value present

in the room exceeds the

set value, the red led lights up

and the relay switches between

contacts 1-2.

Note: In order to preserve the life of the system, the minimum time between

a relay switching and the next one is 1 minute. However, the led status

updating is immediate. Therefore, after using the regulation knob, it is

possible to find a discrepancy between what is indicated by the led and the

actual status of the relay. This condition lasts for up to 1 minute.

The device has two ring nuts to limit mechanically the range of settable

values if the humidistat is installed in public places or in hotel rooms.

To limit the range, proceed as follows:

- Set the knob in an intermediate value of the desired range

- Remove the knob.

- Under the knob there are two ring nuts marked by the word “min” and

“MAX”, respectively for the lower and upper limit.

- Turn the “min” ring nut clockwise and “MAX” anticlockwise until the

minimum value range (see the humidity values reported on the cover).

- Turn the “MAX” ring nut anticlockwise and until the maximum value

range (see the humidity values reported on the cover).

- Replace the knob, making sure that the indicator of the setpoint on the

knob is in the same position when the knob has been removed.

To remove the limitation to the setpoint and reset the range 30% ÷ 90% RH

turn the two ring nuts up to bring the locks of limitation in a position outside

the range 30% ÷ 90% RH.

• Fix the device inside the 3 modules box in compliance with the assembly diagrams

described on the back of this instruction sheet. The accessories for the installation

included in the package allow the mounting of the plates described in the diagram

“adjustable cover plates” and they are:

- A mount

- B mount (it could be necessary to remove the side cogs)

- AIR mount

- couple of side BM plastic elements (both of white colour and grey colour)

- couple of side VI plastic elements (both of white colour and grey colour)

- covers and knobs of white colour and anthracite grey colour.

The adapters inside the box allow the monitoring of the following cover plates:

For information about the possibility to adapt the humidistat with different

cover plates from those listed, contact the Technical Service.

* through mount that you can buy on request (code VE767500)

• All the above trademarks are the property of their respective owners.

ABB Chiara series

ABB Mylos series

Ave S44 series

Bticino Axolute series

Bticino Axolute Air*

Bticino Light series

Bticino Light tech series

Bticino Living series

Bticino Livinglight series

Bticino Livinglight Air series

Bticino Matix series

Gewiss Chorus series

Vimar Eikon series

Vimar Eikon Evo series

Vimar Idea series

Vimar Plana series

Vimar Arké series

10-2017

User Manual

ELECTRONIC FLUSH-MOUNTING HUMIDISTAT

 Read all instructions carefully

OPERATION

PACKAGE CONTENTS

WIRING DIAGRAMS

ADJUSTABLE COVER PLATES

INSTALLATION

Cover, knob and plastic elements are available in white and anthracite grey colours

humidistat

Covers VI plastic

elements

BM plastic

elements

A mount B mount

Setpoint modification

Error probe signal

AIR mount

COM

NO NC

N L

230V~

1 2 3 4 5

AIR

AXO AIR

VI*

Bticino Matix series

Bticino Living, Light, Light Tech, Livinglight, Axolute series

Vimar Eikon, Eikon Evo, Plana series

Ave S44 series – ABB Mylos series

Remove the cogs Remove the cogs

Bticino Livinglight AIR series

* Note: If the box extension is not present (adapter

which increases the depth of the in-built box)

we recommend using the frame for installation

Livinglight AIR. AXO AIR mount not included in the package.

Bticino Axolute AIR series

* Note: only for installing the Vimar Idea series

cover plate, use the side plastic elements VI.

ABB Chiara series

Vimar Arké series, Idea

Gewiss Chorus series

MOUNTING

Product specificaties

Merk:	Vemer
Categorie:	Luchtbevochtiger
Model:	Humi

Heb je hulp nodig?

Als je hulp nodig hebt met Vemer Humi stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Luchtbevochtiger Vemer

Vemer Akuos 230 Handleiding

29 Mei 2023

Vemer Hygros Handleiding

7 Mei 2023

Vemer Humi Handleiding

26 April 2023

Vemer Akuos Handleiding

6 April 2023

Handleiding Luchtbevochtiger

Nieuwste handleidingen voor Luchtbevochtiger

Ruggard PDC9-BRS Handleiding

13 December 2024

Ruggard EDC-600L Handleiding

13 December 2024

Ruggard PDC10-CYS Handleiding

13 December 2024

Ruggard PDC24-BB Handleiding

13 December 2024

Ruggard EDC-235L Handleiding

13 December 2024

Ruggard PDC24-BBS Handleiding

13 December 2024

Ruggard EDC-FP90L Handleiding

13 December 2024

Ruggard PDC10-CY Handleiding

13 December 2024

Vornado Votiv 7 Handleiding

7 December 2024

Vornado EV3 Handleiding

7 December 2024