Velleman WS1070 Handleiding

Velleman Weerstation WS1070

Lees hieronder de 📖 handleiding in het Nederlandse voor Velleman WS1070 (32 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 772 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

S1070

WIRELESS WEATHER STATION + DCF CLOCK AND OUTDOOR SENSOR

DRAADLOOS WEERSTATION + DCF-KLOK EN BUITENSENSOR

STATION MÉTÉO SANS FIL + HORLOGE DCF ET CAPTEUR EXTÉRIEUR

ESTACIÓN METEOROLÓGICA INALÁMBRICA CON RELOJ DCF Y SENSOR EXTERIOR

DRAHTLOSE WETTERSTATION MIT DCF-UHR UND AUßENSENSOR

USER MANUAL

GEBRUIKERSHANDLEIDING

NOTICE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

WS1070_v4 VELLEMAN 2

WS1070 – WIRELESS WEATHER STATION + DCF CLOCK AND OUTDOOR SENSOR

1. Introduction & Features

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the WS1070! This is a wireless weather station with DCF clock and outdoor sensor. Please read

the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it

and contact your dealer. Note that damage caused by disregard of certain guidelines in this manual is not covered by

the warranty and the dealer will not accept responsibility for any ensuing defects or problems. Contents: 1 x base

station, 1 x remote outdoor sensor (including a thermo-hygro, rain and wind sensor), 2 x adjustable hoops, 2 plastic

arms and this manual.

2. Setting up Your Weather Station

• Open the housing of the remote sensor to reveal the two sockets (wind and rain sensor).

• Connect the cables of the wind and the rain sensor to the corresponding sockets.

• Open the battery compartment of the outdoor sensor and insert 2 x AA alkaline batteries. Mind the polarity.

• Open the battery compartment of the weather station and insert 3 x AA alkaline batteries. Mind the polarity.

Every time the outdoor sensor is powered up (after e.g. a battery replacement), the LED indicator will light for 4

seconds (if no LED lights, make sure the batteries are correctly inserted). The sensor will transmit data every 24

seconds after which it will start radio-controlled time reception. After the RCC time reception (± 5 minutes) no

data will be transmitted. The LED will blink 5x once the RCC signal is synchronized. Regular RF link will be

established once the RCC reception routine is finished.

When the weather station is powered up, a short beep will sound and all LCD segments will light for 3 seconds

before the station enters into the learning mode.

Do not press any key during the learning period (± 10 minutes). After both indoor and outdoor data is

displayed you can install the remote outdoor sensor and set the time (if no RCC reception is available). If there is

no temperature reading on the outdoor station make sure both units are within transmission range or check the

batteries. If you press a key before the weather station receives the temperature signal, take out the batteries and

reinstall them after ± 10 seconds.

Time and date are provided by a highly accurate atomic clock. Note that, whenever reception is possible, the

weather station will scan for the DCF radio signal and overwrite a manually set time and date.

3. Mounting the Units

a. The Base Station

Place the base station onto a flat surf the back of the unit. The unit can ace by deploying the foldable legs at

also be wall-mounted. It is important to check that the radio signal can be received before permanently

mounting both units.

WS1070_v4 VELLEMAN 3

b. The Outdoor Station

To achieve accurate results, the mast must be securely mounted onto a horizontal surface and in an open

area away from trees or other shelters. Check that the anemometer can rotate freely and that the wind can

reach the meter from all sides. Mount the sensors according to the pictures.

• The Wind Sensor (fig. 1)

• The Rain Sensor (fig. 2)

• The Thermo-Hygro Sensor (fig. 3)

Product specificaties

Merk:	Velleman
Categorie:	Weerstation
Model:	WS1070
Kleur van het product:	Grijs
Ingebouwd display:	Ja
Breedte:	150 mm
Diepte:	28 mm
Hoogte:	161 mm
Meeteenheid temperatuur:	°C
Accu/Batterij voltage:	1.5 V
Alarm functie:	Ja
Batterij bijna leeg-indicatie:	Ja
Barometer meetbereik:	91.9 - 108 kPa
Klok functie:	Ja
Ophangsysteem voor aan de muur:	Ja
Meetfuncties:	Indoor barometer, Indoor hygrometer, Indoor thermometer, Outdoor hygrometer, Outdoor thermometer, Rain sensor, Anemometer (wind speed)
Meetfuncties trend display:	Barometer, Hygrometer, Thermometer
weerstation extremum data:	Thermometer
Weersvoorspelling:	Ja
Type batterij:	AA
Vochtigheid meetbereik (buiten) (H-H):	1 - 99 procent
Temperature measurement range (outside) (T-T):	-40 - 65 °C
Temperature measurement range (inside) (T-T):	0 - 60 °C
DCF radio klok:	Ja
Windsnelheid meting bereik:	0 - 50 m/s
Windsnelheid meting eenheid:	km/u