US Blaster USB 7329 Handleiding
US Blaster
DJ Party Music
USB 7329
Lees hieronder de 📖 handleiding in het Nederlandse voor US Blaster USB 7329 (23 pagina's) in de categorie DJ Party Music. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/23
1
DESCRIPTION OF THE FUNCTIONS
Top View:
1. L.C.D.
These liquid crystal displays (L.C.D.) indicate the track numbers, time (minutes, seconds, frames), pitch range, and relative playback information.
2. Seamless Loop
There is A, B/LOOP/ EXIT, RELOOP buttons.
i. . A BUTTON---“start point” (A point. Also, Cue 1 could be A point) After setting up the A point, the green Led light up
ii. . B / LOOP EXIT BUTTON: ---“ End point”(B point). Press the B /LOOP button to set up the B point and start the loop playback automatically. Loop
lights on the display and the 3 LEDs flash. Press this button again to exit the LOOP playback.
iii. . Return to the loop playback by pressing the RELOOP while in performance.
iv. . Change “ START POINT” and” END POINT” by pressing the A& B/ LOOP EXIT button again
v. The interval between A and B point must be more than 20 frames; otherwise, the B point will be canceled, then LOOP function disappears and LOOP fades
on the display
3. Instant Reverse
i. When Instant Reverse mode ON, the Brake sound cause by motor reverse will not be heard.
Under this mode, If the track reverses back from 00:50, and switch back to forward play as 00:45. The track will start to play from 00:55
Please note that there is a 10 seconds buffer for this mode, which means the track can reverse 10 seconds backwards from the point you selected.
ii. Hold the Instant Reverse button for 3 seconds and the LED flashing.
Under this mode, the track starts reverse and forward play instantly from the switch point
If the track reverses back from 00:50, and switch back to forward play as 00:45. The track will start to play from 00:45
2
4. Forward/Reverse
Control the direction of the Platter
5. TIME / STOP BUTTON
This button switches the time display between total remaining time, remaining time of the current song, elapsed playing time. The unit will be in the
“stop” mode if you continue pressing the button for 3 seconds.
6. 3 HOT-CUE
This unit will allow you to play from 3 cue points instantly.
a.Set CUE memory: Press the MEMO button first, and then press the CUE button to complete the CUE setting, then this CUE button will light up.
b.Play” CUE” memory: Upon pressing specific CUE button, it will flash about 5 seconds.
Note: This function is not available during perform REVERSE sound effect.
7. Motor ON/OFF
Switch of the Platter Motor
8. BOP BUTTON
The playback will automatically play from the CUE point upon the button is pressed.
9. CONTINUE/SINGLE Button
To press this button it can switch between auto cue single and continue. The selected mode is indicated on the display.
*AUTO CUE SINGLE - After each track, the unit pauses at the beginning of next track. The playback starts from audible point.
*CONTINUE -To play all tracks continually.
*OUTRO - The unit will play the last 30 seconds of each track. Press the button for 3 seconds to switch OUTRO function.
10. CUE BUTTON
The cue function allows the CD returning to the memorized point. In PAUSE mode, pressing the CUE button to set the cue point, and the CUE button
blinks; in PLAY mode, press this button to pause the unit at the memorized point.
11. PLAY/ PAUSE BUTTON
Each press of this button causes the operation to change between PLAY and PAUSE modes.
12. TRACK/FX PARAMETER KNOB
The Knob select the track to be played and FX Parameter adjust
13. SEARCH BUTTON
Pressed the button to switch the function of Jog Dial between SEARCH and PITCH BEND.
When the indicator LED is light, dial the jog for quick search forward and backward.
When the indicator LED is off, dial the jog for pitch bend function.
If the jog is unmoved for 8 seconds, the indicator light will go off.
14. PROGRAM BUTTON
You can program the track you want. While the unit is stopped, press the PROG button first to enter memorized mode, by pressing the skip buttons
to select the tracks you want to order and then press the PROG button again to compete set up per track. The max tracks you can program are 16
tracks per disc. While playing programmed tracks, the LED of PROG lights up. While the unit is stopped, open the tray disc or turn off the power,
the program will be exit.
This button can be used for DISC IDENTIFICATION, please note the point 22
15. PITCH BEND + / - BUTTON
When each of the two CD players is playing, the pitch bend function allows the position of the bass beat to be matched after the pitch has been adjusted. The
pitch will automatically rise up to + 16% from the current setting while pressing the “ + “button. While pressing the “ – “ button, the pitch will automatically drop
to - 16 % from current setting. By the way of changing the pitch the position of the beats can be matched
16. PITCH CONTROL SLIDER
To match the choices of playback speed (8%, 16%, 50%), you can choose what range you want between minimum (up side) and maximum (bottom
side) by moving the pitch control slider.
.
17. KEY ON/OFF SWITCH
Press the button to switch KEY mode on or off.
KEY OFF: The display shows the “KEY” in blinking, and the key changed according to the pitch change. The key parameter adjustment is not in
effect
KEY ON: The “KEY” lights on the display, turning the SCOPE knob to adjust the key. Slide the pitch slider will also change the key.
18. PITCH ON/OFF BUTTON
Press the button to be PITCH ON mode, press it again on the PITCH ON mode, and blinks with unit on the PITCH OFF mode.
19. PITCH % SELECT BUTTON
Select the pitch change range from ±8%, ±16%, ±50%. The playback speed will change when you move the pitch control slider.
20. TONE ARM SECTION
Type: Universal S-Shape tubular arm
3
21. EFFECT SELECT KNOB
a. Flanger:
b. Filter
c. Echo
Please check page.9 for the basic operation and adjustment.
22. Disc Identification (CDDA ONLY)
i. Disc Identification function is workable in Pause Mode only
ii. Press MEMO Key for 2 sec, LCD Display shows “SAVE” and MAIN CUE time.
That means the Main Cue point is saving into EEPROM.
As “SAVE” and “MAIN CUE Time” disappear from LCD after 3 seconds, the Main Cue point save procedure is completed.
iii. When EEPROM recognize that there is the MEMO record, LCD Display shows “CUE“
iv. When EEPROM recognize that there is saved CUE Point in EEPROM. LCD Display shows “LOAD” and “MAIN CUE time”
v. Press MEMO + MAIN CUE to Load the Saved CUE TIME to MICON MAIN CUE
vi. Press TIME Button and Switch the Power ON , Press MEMO for 3 sec in “No disc mode” to clear the Memory from EEPROM
As LCD shows “ RESET ” for 3 seconds, the data is cleared.
23. SLEEP:
Leave the unit unused for 30 minutes; the machine will shut off automatically.
DESCRIPTION OF THE FUNCTIONS
Front View
1. CD/Mix/TT
Switch of CD/Mix/TT mode
2. RPM selector
Selector of 33/45/78 rpm, holds the button for 3 seconds to switch to 78 rpm
3. EJECT BUTTON
Press to eject the disc.
Note: Disc can’t be ejected unless the stop or pause button has been pushed first
4. Drive in use light
Light will blink when the disc drive is in use.
5. DISC SLOT
Insert and remove the CDDA disc.
Product specificaties
Merk: | US Blaster |
Categorie: | DJ Party Music |
Model: | USB 7329 |
Heb je hulp nodig?
Als je hulp nodig hebt met US Blaster USB 7329 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding DJ Party Music US Blaster
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
22 Maart 2023
Handleiding DJ Party Music
- DJ Party Music Pioneer
- DJ Party Music Atomix
- DJ Party Music Envivo
- DJ Party Music Gemini
- DJ Party Music Hercules
- DJ Party Music Ion
- DJ Party Music Koden
- DJ Party Music Native
- DJ Party Music Numark
- DJ Party Music Serato
- DJ Party Music Skytec
- DJ Party Music Vonyx
Nieuwste handleidingen voor DJ Party Music
24 September 2023
25 Augustus 2023
25 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
15 Augustus 2023
14 November 2022
15 Augustus 2023