Uniden GMR3050-2C Handleiding

Uniden Radio GMR3050-2C

Lees hieronder de 📖 handleiding in het Nederlandse voor Uniden GMR3050-2C (4 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 69 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

GMR3050-2C

Congratulations on your purchase of a Uniden GMRS/FRS

radio. This lightweight, palm-sized radio is a state-of-the-art

device, equipped with many valuable features. Use it at

sporting events, to stay in contact with family and friends,

hiking, skiing, outdoors, or in a neighborhood watch for vital

communication.

• 15 GMRS/7 FRS

Channels

• Battery Charger

• •121 Privacy Codes Silent Mode

• •Up to 30-Mile Range* microUSB charging jack

• •Channel Scan 10 Selectable Call Tone

Alerts

• •VOX Headset Jack Auto Squelch

• Roger Beep

* Range may vary depending on environmental and/or

topographical conditions.

GMR3050-2C HARDWARE

1 Antenna 7 Speaker

2 USB Charge Port/

Headphone Jack

8 Channel and Volume

3 Push to Talk 9 Backlight

4 Microphone 10 CH/LOCK

5 MENU/Power Screen11

6 CALL/MON

WHAT'S IN THE BOX

Your package contains 2 radios, 6 AA

rechargeable NiMH batteries, one AC adapter/

Y-Split microUSB charge cable, 2 belt clips, and

this reference guide.

Visit our web site at www.uniden.com to order

accessories.

Use only Uniden accessories.

The radio operates on the General Mobile

Radio Service (GMRS) frequencies which

require a Federal Communications Commission

license to operate. For licensing information

and application forms, visit the FCC on-line at:

www.fcc.gov/wtb/uls or call the FCC hotline at

1-800-418-3676. If you have any questions you

can contact the FCC direct at 1-888-225-5322.

Each radio uses 3 AA rechargeable NiMH

batteries (included).

To install the batteries:

1. If installed, remove the belt clip.

2. Remove the battery compartment door by

pressing on the latch and releasing the

cover. Remove it.

3. Install the supplied 3 AA NiMH batteries

into the battery compartment. Be certain

to follow the + and – symbols in the

compartment. Installing the batteries

incorrectly will prevent the unit from

operating.

4. Replace the battery compartment door.

5. Replace the belt clip if necessary.

6. Repeat for each radio.

Note: You may also use 3 AA non-rechargeable

alkaline batteries in each radio.

However, do not mix NiMH and alkaline

batteries in the same radio.

CHARGING THE RADIO

Review the following tips before charging your

radios:

CAUTION: Do not attempt to recharge

alkaline batteries. Doing so can

create a safety hazard or damage the

radio.

• Install the batteries before connecting the AC

adapter to the radio and power source.

• The battery icon flashes while the radio

charges, whether the radio is turned on or

not. The charge stops after 14 hours of

continuous charging. If there is a power

interruption, the charging timer resets to 14

hours. If the radio is off and charging stops,

the battery icon stops flashing.

• Charge time may vary depending on the

battery life remaining. For fastest charging,

turn off the radio before charging.

• If battery power is low, you cannot operate

the radio even using external power. If you

try to transmit while power is low, the radio

FCC GMRS LICENSE

INSTALL THE BATTERIES

will automatically turn off. Recharge the

batteries.

GMR3050-2C charges through a microUSB

Y-branch cable (provided) with an AC adapter

end that plugs into an AC power source.

1. Plug one branch of the microUSB Y-Cable

into each radio's microUSB charge port.

2. Insert the AC adapter end into an AC power

source (wall plug).

3. The radio is fully charged when the battery

charging icon stops flashing.

USING THE RADIO

Turning the Radio On and Adjusting the

Volume

1. Press and hold the MENU/ key to turn

the radio ON.

2. To change the volume level, press the

▲ ▼ or key to increase or decrease the

volume level. There are 8 volume levels (L1

- )L8) plus volume off (L0

3. Press and hold the MENU/ key to turn

the radio OFF.

Using Headphones

Your radio has a headphone jack to support

earphones/earbuds (not included). Using the

earbuds lets you have more private

communications. To use headphones/earbuds,

lift the rubber cover from the headset jack, then

plug in the headphones/earbuds.

Important: Your radio is not weather resistant

when using the headset jack. When you remove

the headphones/earbuds, be sure to fully press

the cover into place to restore the radio's

weather resistant capability.

Using the Menu

Press MENU/ to access the three menu

options:

• Privacy Code (121 codes). The privacy codes

display underneath the channel number on

the screen.

• Call Tone (10 call tone options plus Off)

• VOX (5 levels plus Off)

Each menu option is discussed later in the

manual with the feature that uses it.

Choosing a Channel

Your radio has 22 channels you can use to talk

to others. In order to speak to someone, each of

you must be set to the same channel and privacy

code.

Each of the channels 1-22 may have any one of

the privacy codes, 0 (OFF), or 1-121 selected.

Code oF (OFF) indicates no privacy code

selected and your radio can receive a signal

regardless of the code settings of the transmitting

radio.

To choose a privacy code:

1. Press MENU/ until the privacy code

number flashes below the channel number.

2. Press ▲ or ▼ to cycle through the privacy

codes.

3. The radio returns to its normal state after

about 5 seconds.

To choose a channel:

1. Press the CH/LOCK key to access the

channel function; the channel number

flashes.

2. Press▲or▼tomanuallycyclethrough

the channels.

You can only manually cycle through channels

when the channel numbers are flashing.

3. Press CH/LOCK to set the channel.

VOX Feature

CAUTION: Insert headphones into the radio

BEFORE turning on the radio.

Your radio is equipped with a user selectable

Voice Operated Transmitter (VOX) that can be

used for automatic voice transmissions. The

VOX feature is designed to be used with or

without a headset with a microphone.

Transmission is initiated by speaking into the

microphone instead of pressing PTT.

To select a VOX level:

1. Press MENU/ repeatedly until the vox

icon and the VOX sensitivity level (OFF,

1-5) blink.

2. Press ▲ or ▼ to change the VOX

sensitivity levels. Use level 5 for increased

sensitivity to voice in normally quiet

environments, and use a higher level to

reduce undesired activation in very noisy

environments.

Channel Scan Feature

Your radio has a channel scan feature that allows

you to easily scan all 22 channels. When an

active channel is detected, the unit pauses on

that channel until the channel is clear. Then, after

a 2 second delay, the radio continues scanning.

Press CH/LOCK to resume scanning while the

radio is stopped on an active channel.

When it stops on an active channel, press the

PTT button to transmit on that channel.

Using channel scan

Press CH/LOCK then hold ▼or▲for3

seconds. The radio will repeatedly cycle

through all 22 channels. To reverse scan

direction, press the other directional icon.

Press or MENU/ CALL/MON to stop

scanning.

Silent Mode

Silent mode turns off all key beeps when it is

turned on. It does NOT mute call or voice signals

received.

Change Silent mode status (OFF or ON) by first

turning OFF the radio.

• Turn Silent mode off by pressing the MENU/

key to turn the radio ON. Silent mode is off and

key beeps sound. (Default)

• Turn Silent mode on by pressing the and CALL/MON

MENU/ keys to turn the radio back ON. Silent

mode turns on and no key beeps sound.

Talking on Your Radio

When the radio stops on a channel that is transmitting,

you can talk to others on that channel:

Transmitting

1. Press and hold the PTT button and speak in a

clear, normal voice about 2-3 inches away from

the microphone on the earbud cord. (The icon tx

displays while you are transmitting. Pause slightly

after pressing the button before you start PTT

talking to prevent cutting off your transmission.)

2. When you are finished speaking, release the PTT

button. You can now receive incoming calls. While

receiving, the icon displays.rx

Transmitting a Call Alert Tone

Your radio is equipped with a call tone that will be

transmitted when the key is pressed. You CALL/MON

can select from 10 call tones.

1. Press until MENU/ call displays on the screen

and the call tone number displays.

2. Press ▲ or ▼ to cycle through the call tones. A

sample of the tone sounds as you move through

them

3. The radio returns to its normal state after about 5

seconds.

To transmit the call tone, press the CALL/MON key.

Auto Squelch Feature

The radio is equipped with an automatic squelch

system which shuts off weak transmissions and

unwanted noise due to terrain conditions or range

limitations.

Monitor Mode Feature

Your radio allows you to listen for weak signals on the

current channel at the press of a key.

To turn ON Monitor Mode:

Press and hold for 2 seconds. On a CALL/MON

channel that does not have activity, you will hear only

an open-squelch hissing noise and displays.rx

To turn OFF Monitor Mode:

Press the key for 2 seconds again.CALL/MON rx

does not display.

Backlight

Press and hold to turn on the LCD backlight. The

screen stays illuminated for 10 seconds before the

backlight turns off.

Key Lock

1. ; Press and hold CH/LOCK displays. The

following functions are not affected by Key Lock:

• Volume adjust

• Enter monitor mode

• PTT transmission

• Backlight

• Power off

2. Press and hold CH/LOCK again; disappears.

Channels 15 GMRS/7 FRS

Privacy Codes 38 Sub-Codes

83 DCS Codes

Operating

Frequency

UHF 462.5500 - 467.7125 MHz

Power Source 3 AA NiMH Batteries per radio

FREQUENCY CHART

CH Freq.[MHz] -

Cross Ref.

CH Freq.[MHz] -

Cross Ref.

1 462.5625 - FRS &

GMRS 1

12 467.6625 - FRS 12

2 462.5875 - FRS &

GMRS 2

13 467.6875 - FRS 13

3 462.6125 - FRS &

GMRS 3

14 467.7125 - FRS 14

4 462.6375 - FRS &

GMRS 4

15 462.5500 - GMRS

5 462.6625 - FRS &

GMRS 5

16 462.5750 - GMRS

6 462.6875- FRS &

GMRS 6

17 462.6000 - GMRS

7 462.7125 - FRS &

GMRS 7

18 462.6250 - GMRS

8 467.5625 - FRS 8 19 462.6500 - GMRS

9 467.5875 - FRS 9 20 462.6750 - GMRS

10 467.6125 - FRS 10 21 462.7000 - GMRS

11 467.6375 - FRS 11 22 462.7250 - GMRS

RBRC INFORMATION

As part of our commitment to protect the

environment and conserve natural

resources, Uniden voluntarily participates

in an RBRC® industry program to collect

and recycle used Ni-MH batteries within

the US.

Please call 1-800-8-BATTERY for information on Ni-MH

battery recycling in your area. (RBRC

® is a registered

trademark of the Rechargeable Battery Recycling

Corporation.)

SPECIFICATIONS

Fonctionnement de l’appareil, lorsque porté sur le

corps. Cet appareil a été testé et s’est avéré conforme

aux normes d’Industrie Canada et approuvé pour le

port sur le corps à l’aide des accessoires Uniden

inclus et conçus pour cet appareil. L’utilisation

d'accessoires ne respectant pas les exigences

d'exposition RF d’Industrie Canada doit être évitée.

FCC Compliance

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by

the party responsible for compliance could void your

authority to operate the equipment.

Avis de conformité à la FCC : Ce dispositif a été testé

et s’avère conforme à l’article 15 des règlements de la

Commission fédérale des communications (FCC). Ce

dispositif est soumis aux conditions suivantes: 1) Ce

dispositif ne doit pas causer d’interférences nuisibles

et; 2) Il doit pouvoir supporter les parasites qu’il reçoit,

incluant les parasites pouvant nuire à son

fonctionnement.

Tout changement ou modification non approuvé

expressément par la partie responsable pourrait

annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

IC Compliance

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept

any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressley approved by

the party responsible for compliance could void your

authority to operate the equipment.

L’appareil est conforme aux normes d’Industrie

Canada. Son fonctionnement est soumis aux deux

conditions suivantes : (1) Ce dispositif ne doit pas

causer d’interférences et (2), il doit pouvoir accepter

les interférences, incluant celles pouvant nuire à son

fonctionnement normal.

Tout changement ou modification non approuvé

expressément par la partie responsable pourrait

annuler le droit à l’utilisateur de faire fonctionner cet

équipement.

FCC RF EXPOSURE INFORMATION

WARNING! Read this information before using the

radio.

In August 1996 the Federal Communications

Commission (FCC) of the United States with its action

in Report and Order FCC 96-326 adopted an updated

safety standard for human exposure to radio

frequency electromagnetic energy emitted by FCC

regulated transmitters. Those guidelines are

consistent with the safety standard previously set by

both U.S. and international standards bodies. The

design of the radio complies with the FCC guidelines and

these international standards. Never allow children to operate

the radio without adult supervision and the knowledge of the

following guidelines.

WARNING! It is up to the user to properly operate this radio

transmitter to insure safe operation. Please adhere to the

following: Use only the supplied or an approved antenna.

Unauthorized antennas, modifications, or attachments could

impair call quality, damage the radio, or result in violation of

FCC regulations.

Do not use the radio with a damaged antenna. If a damaged

antenna comes into contact with the skin, a minor burn may

result. Please contact your local dealer for a replacement

antenna.

ONE YEAR LIMITED WARRANTY

IMPORTANT! SAVE YOUR RECEIPT! Evidence of original

purchase is required for warranty service.

WARRANTOR: UNIDEN AMERICA CORPORATION

("Uniden")

ELEMENTS OF WARRANTY: Uniden warrants, for one year,

to the original retail owner, this Uniden Product to be free from

defects in materials and craftsmanship with only the limitations

or exclusions set out below.

WARRANTY DURATION: This warranty to the original user

shall terminate and be of no further effect 12 months after the

date of original retail sale. The warranty is invalid if the

Product is: (A) damaged or not maintained as reasonable or

necessary, (B) modified, altered, or used as part of any

conversion kits, sub-assemblies, or any configurations not

sold by Uniden, (C) improperly installed, (D) serviced or

repaired by someone other than an authorized Uniden service

center for a defect or malfunction covered by this warranty, (E)

used in any conjunction with equipment or parts or as part of

any system not manufactured by Uniden, or (F) installed or

programmed by anyone other than as detailed by the owner’s

manual for this product.

STATEMENT OF REMEDY: In the event that the product

does not conform to this warranty at any time while this

warranty is in effect, warrantor will either, at its option, repair

or replace the defective unit and return it to you without

charge for parts, service, or any other cost (except shipping

and handling) incurred by warrantor or its representatives in

connection with the performance of this warranty. Warrantor,

at its option, may replace the unit with a new or refurbished

unit.

THE LIMITED WARRANTY SET FORTH ABOVE IS THE

SOLE AND ENTIRE WARRANTY PERTAINING TO THE

PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL

OTHER WARRANTIES OF ANY NATURE WHATSOEVER,

WHETHER EXPRESS, IMPLIED OR ARISING BY

OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.THIS

WARRANTY DOES NOT COVER OR PROVIDE FOR THE

REIMBURSEMENT OVERPAYMENT OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES. Some states do not allow this

exclusion or limitation of incidental or consequential damages

so the above limitation or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you specific legal

rights, and you may also have other rights which vary from

state to state. This warranty is void outside the United States

of America and Canada.

MAINTENANCE

Never change or replace anything in your radio except

the batteries.

Care and Safety

To clean the radio, use a soft cloth dampened with

water. Do not use cleaners or solvents because they

can harm the body of the unit and leak inside, causing

permanent damage. Use a dry, lint-free cloth to clean

the battery contacts. Do not submerge the unit in

water. If the unit gets wet, turn it off and remove the

batteries immediately.

Dry the battery compartment with a soft cloth to

minimize potential water damage. Leave the battery

compartment cover off overnight to ensure complete

drying. Do not use the radio until the unit is completely

dry.

Your radio might cause TV or radio interference even

when it is operating properly. To determine whether

your radio is causing the interference, turn it off. If the

interference goes away, your radio is causing it. Try to

eliminate the interference by moving your radio away

from the receiver. If you cannot eliminate the

interference, the FCC requires that you stop using the

radio.

Hazardous Environments

Do not operate the radio in hazardous environments.

Explosion or fire may result. Do not operate the radio

near unshielded electrical blasting caps.

Under certain conditions, radios can interfere with

blasting operations and may cause an explosion. Turn

your radio OFF to prevent accidental transmission

when in a blasting area or in areas posted: "Turn off

two-way radio." Construction crews often use remote

control RF devices to set off explosives.

REGULATORY INFORMATION

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-

to-face) operations with a 1 inch spacing from the

front of the radio. For hand-held operation, the radio

should be held 1 inch from the user's face in order to

comply with FCC RF exposure requirements.

Body-Worn Operation

This device was evaluated for body-worn operations

with the supplied belt-clip accessory. (All necessary

accessories are included in the package; any

additional or optional accessories are not required for

compliance with the guidelines.) Third party

accessories (unless approved by the manufacturer)

should be avoided as these might not comply with

FCC RF exposure guidelines.

For body-worn operation, this device has been tested

and meets the Industry Canada RF exposure

guidelines when used with Uniden accessories

supplied or designated for this product. Use of other

accessories may not ensure compliance with Industry

Canada RF exposure guidelines.

PROCEDURE FOR OBTAINING PERFORMANCE OF

WARRANTY: If, after following the instructions in the owner’s

manual you are certain that the Product is defective, pack the

Product carefully (preferably in its original packaging). The

Product should include all parts and accessories originally

packaged with the Product. Include evidence of original

purchase and a note describing the defect that has caused you

to return it.The Product should be shipped freight prepaid, by

traceable means, to warrantor:

Uniden America Corporation

C/O Saddle Creek

743 Henrietta Creek Road, Suite 100

Roanoke, TX 76262

Product specificaties

Merk:	Uniden
Categorie:	Radio
Model:	GMR3050-2C
Kleur van het product:	Black,Grey
Ondersteund aantal accu's/batterijen:	3
Hoeveelheid tonen:	10
Maximumbereik:	48280 m
Frequentie:	462.5500 - 467.7125 MHz
Oplaadbaar:	Ja
Riemclip:	Ja
Batterijtechnologie:	Nikkel-Metaalhydride (NiMH)
Type batterij:	AA
Aantal kanalen (totaal):	22 kanalen