Uni-T UT118B Handleiding

Uni-T Multimeter UT118B

Lees hieronder de 📖 handleiding in het Nederlandse voor Uni-T UT118B (2 pagina's) in de categorie Multimeter. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Measurement Operation

Before measurement, anticlockwise circumgyrate the

red cover and rock the input terminal.

When all themeasurement has been completed,

deasil circumgyrate the red cover then hide the input

terminal. (see gure 3)

Figure 3

1. AC / DC Voltage auto Measurement.

Warning

To avoid harm to the Meter, never input higher than

300V voltage although it is possible to measure

higher voltage.

To measure Voltage, connect the Meter as follows:

● Set the switch to V .

● Auto measuremeng mode is a default. Under this

mode can measure AC voltage and DC voltage.

● Connect the test leads across with the object

being measured. The measured value shows on

the display.

● When voltage measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test, and remove the

testing leads away from the input terminal of the

meter.

Note:

The threshold voltage of AC voltage is around 400mV.

2. DC Voltage Measurement

Warning

To avoid harm to the Meter, never input higher than

300V voltage although it is possible to measure

higher voltage.

● Set the switch to V .

● Press SELECT to select DC voltage measurement

mode.

● Connect the test leads across with the object

being measured. The measured value shows on

the display.

● When voltage measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test, and remove the

testing leads away from the input terminal of the

meter.

International Electrical Symbols

Deciency of Built-In Battery

Grounding

AC (Alternative Current)

DC (Direct Current)

Double Insulated

Continuity Test

AC or DC

Diode

Conforms to Standards of European

Warning. Refer to the Operating Manual

The Meter Structure (see gure 1)

1. Front Housing 2. Functional buttons

3. Switch 4. LCD Display

5. Input Terminals

Display Symbols (see gure 2)

Figure 2

1. Indicates auto scan mode

2. High voltage indicator

3 Data hold is active

4. Indicates negative reading

5. The meter is in the autorange mode

6. Indicator for AC voltage

7. Indicator for DC voltage

8. The battery is low

Warning: To avoid false readings, which could

lead to possible electric shock or personal injury,

replace the battery as soon as the battery indicator

appears.

9. Minimum reading.

10. Maximum reading.

11. The unit of Capacitance

12 Test of diode

13. The continuity buzzer is on.

14. V : Volts. The unit of voltage.

mV : Millivolt. 1x10 or 0.001 volts.

15. Ω: Ohm. The unit of resistance

kΩ : kilohm. 1x10 or 1000 ohms.

MΩ: Megaohm. 1x10 or 1,000,000 ohms

Button function and auto power off

1.SELECT

Press to switch between resistance, AC/DC SELECT

voltage, continuity buzzer and diode measurement

modes. Press and hold more than 2 seconds in or

exit “sleep” mode.

UT118A/B Operating Manual

Pen Type Meters

UT118A/B

Operating Manual

Overview

This Operating Manual covers information on safety

and cautions. Please read the relevant information

carefully and observe all the Warnings and Notes

strictly.

Warning

To avoid electric shock or personal injury, read the

"Safety Information" and "Rules for Safe Operation"

carefully before using the Meter.

The Model UT118A and UT118B (hereafter referred

to as “the Meter”) are 3000 counts pen type digits

millimeters. The Meter uses large scale of integrated

circuit with professional multimeter IC as its core and

has full range overload protection.

The Meter measures or tests the following:

● AC/DC voltage

● EF Function (UT118B only)

● Resistance

● Diode

● Continuity

● Capacitance

Unpacking Inspection

Open the package case and take out the Meter.

Check the following ite ms carefully to see any

missing or damaged part:

Item Description Qty

1 English Operating Manual 1 piece

2 Test Lead 1 pair

In the event you nd any missing or damage, please

contact your dealer immediately.

Safety Information

This Meter complies with standards EN61010: in

pollution degree 2, over voltage category (CATIII

300V) and double insulation.

CATIII: Distribution level, fixed installation, with

smaller transient over voltages than CAT IV.

Use the Meter only as specified in this operating

manual, otherwise the protection provided by the

Meter may be impaired.

In this manual, a Warning ide ntifies con ditions

and actions that pose hazards to the user, or may

damage the Meter or the equipment under test.

A Note identies the information that user should pay

attention on.

Rules For Safe Operation

Warning

To avoid possible electric shock or personal injury,

and to avoid possible damage to the Meter or to the

equipment under test, adhere to the following rules:

● Before using the Meter inspect the case. Do not

use the Meter if it is damaged or the case (or part

of the case) is removed. Look for cracks or missing

plastic. Pay attention to the insulation around the

connectors.

● Inspect the test leads for damaged insulation or

exposed metal. Check the test leads for continuity.

Replace damaged test leads with identical model

number or electrical specifications before using the

Meter.

● When using the test leads, keep your fingers

behind the nger guards.

● Do not apply more than the rated voltage, as

marked on the Meter, between the terminals or

between any terminal and grounding.

● When the Meter working at an effective voltage

over 60V DC or 30V AC, special care should be

taken for there is danger of electric shock.

● Use the proper function, and range for your

measurements.

● Disconnect circuit power and discharge all high

voltage capacitors before testing current, resistance,

diodes or continuity.

● Repl ace the b attery as soon as the battery

indicator appears. With a low battery, the Meter

might produce false readings that can lead to electric

shock and personal injury.

● When ser vicing th e M e te r, u se only th e

same model or identical electrical specifications

replacement parts.

● The internal circuit of the Meter shall not be

altered at will to avoid damage of the Meter and any

accident.

● Soft cloth and mild detergent should be used to

clean the surface of the Meter when servicing. No

abrasive and solvent should be used to prevent the

surface of the Meter from corrosion, damage and

accident.

● Do not use or store the Meter in an environment

of high temperature, humidity, explosive, inammable

and strong magnetic field. The performance of the

Meter may deteriorate after dampened.

Figure 1

2. HOLD

Press HOLD to enter and exit hold mode (except

under auto scan mode).

Press and hold the HOLD button more t han 2

seconds, the meter automatically holds the value

which obtains at 6 seconds later, at this time, is

displayed and ickering.

If enter “sleep” mode under hold mode, the meter still

in the hold mode when it be turned on.

3. MAX/MIN

The MAX /MIN mode stores minimum (MIN) and

maximum (MAX) input values (except under auto scan

mode). Manual ranging comes when you select this

function.

Press button MAX MIN MAX/MIN MAX/MIN

and vice versa.

Under hold mode and max/min mode, should exit hold

mode rst then press and hold MAX/MIN more than 1

second to exit max/min mode.

Display Backlight and test lead light button, Press

once to turn the display backlight and test lead light

on and press again to turn the display backlight and

test lead light off. It will automatically off after around

1 minute.

5. AUTO POWER OFF

To preserve battery life, the Meter automatically goes

into a “sleep” mode if you do not press any button for

around 10 minutes. The Meter can be activated by

pressing any button, then returns to the display for the

function selected previously

6. BUZZER

The buzzer phonate go with every time button be

effectual pressed. When the meter will auto power off

in 20 seconds the buzzer beeps three times. Before

power off there will be a long time buzzer beeps.

-3

E. Continuity Measurement

Range Resolution Remark

Open Circuit Voltage around

-1.2V;Buzzer beeps at resistance

≤10Ω; Buzzer not sound when

resistance > 70Ω;

F. Diodes Measurement

Range Resolution Overload Protection

1mV 300Vrms

Remark: Open Circuit Voltage around 3V, Displays

approximate forward voltage drop.

G. Capacitance

Range Resolution Accuracy Overload Protection

3nF 0.001nF

30nF 0.01nF

300nF 0.1nF

3μF 1nF

30μF 10nF

300μF 100nF ±(5%+5)

3mF reference

Remarks:

1. Under auto scan mode the max range is 300μF.

2. There is a residual reading when the circuit is open.

To measure a small value of capacitance, subtract it

to ensure accuracy.

Maintenance (see gure 4)

This section provides basic maintenance information

and battery replacement instruction.

Figure 4

Warning

Do not attempt to repair or service your Meter unless

you are qualified to do so and have the relevant

calibration, performance test, and service information.

To avoid electrical shock or damage to the Meter, do

not get water inside the case.

A. General Service

● Periodically wipe the case with a damp cloth and

mild detergent. Do not use abrasives or solvents.

● To clean the terminals with cotton bar with

detergent, as dirt or moisture in the terminals can

affect readings.

● Turn the Meter off when it is not use and take out

the battery when not using for a long time.

● Do not store the Meter in a place of humidity,

high temperature, explosive, inammable and

strong magnetic eld.

B. Replacing the Battery

Warning

To avoid false readings, which could lead to possible

electric shock or personal injury, replace the battery

as soon as the battery indicator appears.

To replace the battery:

1. Turn the Meter off. Disconnect the connection

between the testing leads and the circuit under test,

and remove the testing leads away from the input

terminals of the Meter.

2. Remove the screw from battery compartment and

separate the battery compartment from the case

bottom.

3. Remove the battery from the battery compartment.

4. Replace the battery with a new 3V battery

5. Rejoin the case bottom and the battery

compartment, and reinstall the screw.

UT118A/B Operating Manual

Development District,Hu Men Town,Dong Guan City,

Guang Dong Province,China

3. AC Voltage Measurement

Warning

To avoid harm to the Meter, never input higher than

300V voltage although it is possi ble to measure

higher voltage.

● Set the switch to V .

● Press to select AC voltage measurementSELECT

mode

● Connect the test leads across with the object being

measured. The measured value shows on the

display.

● When voltage measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test, and remove the

testing leads away from the input terminal of the

meter.

Note:

The threshold voltage of AC voltage is around 400mV.

4. EF Measurement( UT118B only)

Warning

To avoid harm to the Meter, never input higher than

300V voltage although it is possi ble to measure

higher voltage.

● Set the switch to V EF and remove the test lead

from the input terminal.

● Press to select EF measurement mode.SELECT

● Unconnected measurement. Place the red

terminals towards the object being measured.

5. auto measurement

Warning

To avoid damages to the Meter or to the devices

under test, disconnect circuit power and discharge all

the high-voltage capacitors before measurement.

● Set the switch to .

● Auto measuremeng mode is a default, under this

mode can measure Resistance, Diode, Continuity

and Capacitance automatically.

● For better accuracy, it better separate the object

being measured from the circuit before

measurement.

● When voltage measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test.

Note:

Under auto measurement mode, when input:

Resistance: <15Ω or >10MΩ

Capacitance: <400pF or >1mF

Will get an irresponsible value.

6. Resistance Measurement

Warning

To avoid damages to the Meter or to the devices

under test, disconnect circuit power and discharge

all the high-voltage capacitors before measuring

resistance.

To measure resistance, do the following:

● Set he rotary switch to .

● Press SELECT to select measurement mode.Ω

● Connect the test leads across with the object being

measured.

● When resistance measurement has been

completed, disconnect the connection between the

testing leads and the circuit under test, and remove

the testing leads away from the input terminals of

the Meter.

7. Continuity Test

Warning

To avoid damages to the Meter or to the devices

under test, disconnect circuit power and discharge all

the high-voltage capacitors before continuity test.

To measure resistance, do the following:

● Set he rotary switch to .

● Press SELECT to select measurement mode.

● Connect the test leads across with the object being

measured.

● The buzzer sounds continuously if the resistance

of a circuit under test is≤30Ω, it indicates the circuit

is in good connection.

Note:

When continuity measurement has been completed,

disconnect the connection between the testing leads

and the circuit under test, and remove the testing

leads away from the input terminals of the Meter

8. Diodes Test

Warning

To avoid damages to the Meter or to the devices

under test, disconnect circuit power and discharge all

the high-voltage capacitors before measuring diodes.

To measure diode, do the following:

● Set he rotary switch to .

● Press SELECT to select measurement mode

● For better accuracy, it better separate the object

being measured from the circuit before

measurement.

● When diodes measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test.

9. Capacitance Measurement

Warning

To avoid damage to the Meter or to the equipment

under test, disconnect circuit power and discharge

all hig h- v o lt a ge c a p acit o r s b e fore measurin g

capacitance. Use the DC Voltage function to conrm

that the capacitor is discharged.

To measure capacitance, conn ect the Meter as

follows:

● Set he rotary switch to .

● Press SELECT to select measurement mode

● For better accuracy, it better separate the object

being measured from the circuit before

measurement.

● When diodes measurement has been completed,

disconnect the connection between the testing

leads and the circuit under test.

General Specications

● Maximum voltage between red Terminals and

Grounding: 300Vrms.

● Maximum Display: 3000. Updates 4 times/second

● Temperature:

Operating: 0

℃~40℃ (32℉~104℉);

Storage: -10

℃~50℃( 14℉~122℉).

● Relative Humidity: ≤75% @ 0

℃~30℃;

≤ 50% @ 31

℃~40℃

● Altitude: Operating: 2000m; Storage: 10000m.

● Battery Type: 3V Li-MnO2 Button cell battery

● Battery Deciency: Display “ ”.

● Dimensions (HxWxL): 20.18x26.5x181.5mm

● Weight: Approx.90g (battery included).

Accuracy Specications

Accuracy:±(a% reading+b digits)guarantee for 1 year.

Operating temperature: 18

℃ ~ 28℃.

Relative humidity: <75%.

A . AC Voltage

Range Resolution Accuracy

Overload Protection

3V 0.001V

30V 0.01V ± (1%+4) 300Vrms

300V 0.1V

Remark: Input Impedance: ≥10MΩ

Frequency Response: 40Hz ~ 400Hz

B. DC Voltage

Range Resolution Accuracy

Overload Protection

3V 0.001V

30V 0.01V ± (1%+3) 300Vrms

300V 0.1V

Remark: Input Impedance: ≥10MΩ

C. EF Test (UT18B Only)

Range Remarks

<10mm: buzzer beeps;

220V/50H 10~50mm: may and may not beeps;

>50mm: Buzzer not sound

D. Resistance

Range Resolution Accuracy

Overload Protection

300Ω 0.1Ω

3kΩ 1Ω

30kΩ 10Ω

300kΩ 100Ω 300Vrms

3MΩ 1kΩ

30MΩ 10kΩ

Remark: Under auto scan mode the max range is

3MΩ.

± (1%+3)

± (1.5%+5)

±(3%+5) 300Vrms

0.1 Ω

Product specificaties

Merk:	Uni-T
Categorie:	Multimeter
Model:	UT118B
Gewicht:	90 g
Accu/Batterij voltage:	3 V
DC voltage bereik:	3 - 300 V
Afmetingen (B x D x H):	27 x 20 x 182 mm
AC voltage bereik:	3 - 300 V