Ultimate Speed IAN 281376 Handleiding

Ultimate Speed Niet gecategoriseerd IAN 281376

Lees hieronder de 📖 handleiding in het Nederlandse voor Ultimate Speed IAN 281376 (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 255 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

IAN 285690IAN 285690

Walser GmbH

Radetzkystraße 114

A-6845 Hohenems

Email: oﬃce@walsergroup.com

www.walsergroup.com

Last Information Update · Version des informations

Stand van de informatie · Stand der Informationen: 01 / 2017

Ident.-No.: 285690012017-1

GB IE NI

AT CH

GB/IE/NI Assembly and safety advice Page 5

DK Monterings- og sikkerhedshenvisninger Side 6

FR/BE Instructions de montage et consignes de sécurité Page 7

NL/BE Montage- en veiligheidsinstructies Pagina 9

DE/AT/CH Montage- und Sicherheitshinweise Seite 10

Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the

product.

Klap begge sider med illustrationerne ud, inden du læser, og sæt dig ind i alle produktets funktioner.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Produkts vertraut.

Avant de lire le mode d‘emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous ensuite

avec toutes les fonctions du produit.

Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies

van het product.

BE NL

IE NI

NL BE FR BE

GB IE NI

AT CH

CAR SEAT COVER SET

Assembly and safety advice

BILSÆDEBETRÆK-SÆT

Monterings- og sikkerhedshenvisninger

SET AUTOSTOELBEKLEDINGEN

Montage- en veiligheidsinstructies

HOUSSES DE SIEGES AUTO

Instructions de montage et consignes de sécurité

AUTOSITZBEZUG-SET

Montage- und Sicherheitshinweise

CAR SEAT COVER SET

Omvang van de levering

2 x omtrek voorzitting (in 1 of 2 delen, afhankelijk per artikeluitvoering)

2–5 x omtrekken hoofdsteunen (afhankelijk per artikeluitvoering)

1 x omtrek achterbankleuning (in 1 tot 5 delen, afhankelijk per artikeluitvoering)

1 x omtrek achterbank zitvlak (niet deelbaar)

Metalen haken (bevinden zich in de hoofdsteunomtrekken)

Soortenlijst

Leverede dele

2 x betræk til forsæder (med 1 eller 2 dele afhængigt af modellen)

2-5 x betræk til hovedstøtter (afhængigt af modellen)

1 x betræk til ryglæn til bagsædet (med 1 til 5 dele, afhængigt af modellen)

1 x betræk til bagsædet (kan ikke deles)

Metalkroge (sidder i hovedstøttebetrækkene)

Typeliste

Lieferumfang

2 x Bezüge Vordersitze (in 1 oder 2 Teilen, je nach Artikelausführung)

2–5 x Bezüge Kopfstützen (je nach Artikelausführung)

1 x Bezug Rücksitz-Lehne (in 1 bis 5 Teilen, je nach Artikelausführung)

1 x Bezug Rücksitz- Sitzﬂäche (nicht teilbar)

Metallhaken (Beﬁnden sich in den Kopfstützenbezügen)

Typenliste

Contenu de la livraison

2 x housses sièges avant (en 1 ou 2 éléments, selon la référence de l’article)

2-5 x housses appui-têtes (selon la référence de l’article)

1 x housse dossier banquette arrière (en 1 à 5 éléments, selon la référence de l’article)

1 x housse banquette arrière (non fractionnable)

Crochets métalliques (dans les housses des appui-têtes)

Liste de modèle

GB IE NI

Scope of delivery

2 x covers for front seats (in 1 or 2 parts according to design)

2 - 5 x covers for headrests (according to design)

1 x cover for rear backrest (in 1 to 5 parts according to design)

1 x cover for back seat (not separable)

Metal hooks (located in the headrest covers)

List of types

2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

17 18 19 20

21 23 24

25 26 27

28 29 30

31 32 33 34

35 36 37

38 39 40

43 44 45

GB/IE/NI 5

Car seat cover set

• Introduction

We congratulate you on your purchase. You have chosen a high quality product.

The instructions for use are to be considered as part of this product. Before using the

product, please familiarise yourself with all the safety information and instructions

for use. Only use the product as instructed and only for the stated areas of use. If you pass the

product on to anyone else, please ensure that you also pass on all the documentation with it.

• Intended use

Set of car seat covers for the driver‘s seat, passenger‘s seat and the back seats of cars

(according to the enclosed type list).

• Safety instructions

Correct installation res. fastening of the seat covers to the vehicle is essential to guarantee the sa-

fety of the user. Please pay attention to the following information when installing the seat covers:

•

WARNING! DANGER OF SUFFOCATION! Keep the pa-

ckaging out of reach of small children.

• Installation is permissible only in cars that are indicated in the list of types on the pa-

ckaging or in the enclosed, detailed list of types.

• Correct assignment of the seat (driver and front passenger seat). The covers are assig-

ned by the marking „airbag“ attached to the seat cover. This marking must be attached

to the outer side of the backrest (see ﬁg. 1.0).

• Headrest inserts, adjustment levers / wheels for release of backrests or armrests may

not be covered with the seat cover. Allowances must be made for appropriate inserts.

Please observe the instructions given in section “Installation”.

• Displaced seat covers must be repositioned. If this is no longer possible due to a advan-

ced state of wear and tear, the cover must be removed or replaced.

• Manipulation of the opening of the seat covers is not permissible (no covering, sewing

up or repairs by yourself).

This protective cover has been tested by TÜV Rhineland Group.

CAUTION! If the seat covers are installed incorrectly, the proper extension and inﬂa-

tion of the seat air bag cannot be guaranteed in the case of a collision.

• Installation of seat covers

You need a pair of pointed scissors.

Important: Please read the information below before installing the seat covers!

Fig. 1: Remove headrests (in some car models the headrests must be dismantled in

a garage).

Fig. 2: Cover the backrest by pulling the cover downwards.

Fig. 3: Pay attention to the correct assignment of the side airbag label (right / left

seat)! The side airbag label must be located at the outside (door side) of the

respective seat.

Fig. 4: Pull the strap through between the seat and the backrest.

Fig. 5: Then close the fastener.

Fig. 6: Cover the seat from the front to the back.

Fig. 7: Fasten the metal hooks to the rubber loops.

Fig. 8+9: Pull the rear rubber loops between the seat and backrest (as you did with the

strap of the backrest cover). Fasten the metal hooks under the seat according

to the car model (e.g. to the existing metal rods - ATTENTION Do not fasten

to airbag cables!)

Fig. 10: Or fasten all rubber loops together.

ATTENTION!

Openings for backrest releases, adjustment levers, side levers etc. (as described under ﬁg.

11–21) must be cut out.

If your seat is equipped with armrests, proceed as described under ﬁg.

11. Otherwise go to ﬁg. 15.

Fig. 11: Pull the cover down as far as the armrest. The cover must be tightly ﬁtting on top.

Fig 12: Cut the cover in the position of the armrest. The cut-out may not be too large.

Fig. 13: Push up the armrest and pull it through the cut-out opening of the cover.

Fig. 14: Pull the strap through between the seat and the backrest and close with the fastener.

If your seat is equipped with side levers, proceed as described under ﬁg.

15. Otherwise go to ﬁg. 19.

Fig. 15: Cover the seat as described under section 2. The cover must be tightly

ﬁtting on top.

Fig. 16: Cut the cover in the position of the side lever. The cut-out may

not be too large.

Fig. 17+18: With the aid of scissors, push the cover under the guide ﬁtting.

If your seat is equipped with seat frame cladding, proceed as described

under ﬁg. 19. Otherwise go to ﬁg. 22.

Fig. 19: (for Renault) Open the seat frame cladding under the seat.

Fig. 20: (for Mercedes) Open the seat frame cladding under the seat.

Fig. 21: Fold the seat frame cladding under the seat cover. Pull the strap through

between the seat and the backrest. Then close the fastener at the back.

Fig. 22: Cover the headrests.

Fig. 23+24: Position the mounting strip directly above the holes for insertion of the headrest.

Cut open the mounting strip in the exact positions of the headrest holes. With

the aid of the integrated mounting strip, it is not possible for the material to tear.

Fig. 25+26: Push the cover beneath the plastic of the headrest guide covering. In a

few isolated car models, it could be the case that these models have no

headrest guide covering.

Fig. 27+28: Pull the cover for the back seat towards the back of the seat. If necessary,

tilt the back seat forward and fasten the rubber loops at the back to the

metal hooks (according to the car model).

Fig. 29: Position the cover exactly in the location of the seat belt.

Fig. 30: Carefully cut the cover in the position of the seat belt.

Fig. 31: Push the cover under the seat belt holder.

Fig. 32: Pull the cover under the backrest. The cover must be under the seat belt!

Fig. 33: Cut the cover in the position of the belt guide.

Fig. 34+35: Push the cover beneath the plastic of the belt guide.

Fig. 36: The backrest cover is universally suitable for all back seats due to the triple zip faste-

ner division. The zip-in part can be used according to the width of the rear backrest.

Fig. 37: Fasten the rubber loops at the back to the metal hooks.

If your your back seat is equipped with armrests, proceed as described

under ﬁg. 38. Otherwise go to ﬁg. 40.

Fig. 38: Open the zip fasteners. Fold out the armrest. Close the zip fastener up to

the armrest.

Fig. 39: Complete covered armrest.

Fig. 40: In case of divided back seats, open the variable zip fasteners with the

slider facing upwards if necessary.

Fig. 41: Remove the rear headrests.

Fig. 42: Cover the rear headrests.

Fig. 43: Cut the backrest cover in the position of the headrest in an x-shaped form.

Fig. 44+45: Push the cover under the plastic.

• Instructions for care and disposal

Wash the covers by hand Do not iron

Do not use bleach Do not dry clean

Do not dry in a tumbler

The seat covers can be disposed of in the household waste.

Please dispose of the packaging in accordance with the local regulations.

• Service & guarantee

This product has been produced with great care and under continuous quality control. The

product comes with a three year guarantee from date of purchase. Please keep your receipt

safe. The guarantee applies only to material and manufacturing defects and does not ap-

ply to misuse or improper treatment. Your statutory rights, especially the rights of warranty,

are not restricted by this guarantee.

Extent of validity: Please use the service hotline which has been provided for you or contact

the service centre in the European Economic Area.

Costs: Repair or replacement free of charge or a refund of the purchase cost. Shipping

costs will not be charged.

Advisory notice: Before returning your product, contact our hotline by telephone, so

that we can help you with any operating errors.

Service address: Return address:

Walser Industrie- und Handels GmbH Walser Customer Service Germany

oﬃce@walsergroup.com Walser GmbH

www.walsergroup.com Bleicheweg 15, Postfach 3325

Service Hotline: 00800 00300030 DE-88131 Lindau

GERMANY

IAN 285690

Fig. 1.0

Product specificaties

Merk:	Ultimate Speed
Categorie:	Niet gecategoriseerd
Model:	IAN 281376

Heb je hulp nodig?

Als je hulp nodig hebt met Ultimate Speed IAN 281376 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Ultimate Speed

Ultimate Speed IAN 436023 Handleiding

13 April 2024

Ultimate Speed ULGD 3.8 B1 Handleiding

18 Juni 2023

Ultimate Speed IAN 311834 Handleiding

14 Juni 2023

Ultimate Speed IAN 275330 Handleiding

7 Juni 2023

Ultimate Speed DIS-162 Handleiding

11 Mei 2023

Ultimate Speed IAN 21696 Handleiding

10 Mei 2023

Ultimate Speed IAN 113155 Handleiding

7 Mei 2023

Ultimate Speed USLK 22 A1 Handleiding

4 Mei 2023

Ultimate Speed IAN 286000 Handleiding

2 Mei 2023

Ultimate Speed IAN 103292 Handleiding

2 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Smeg KIT6PX Handleiding

21 November 2024

Senal SCI-3212MP Handleiding

21 November 2024

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024

Senal OLM-2S-P Handleiding

21 November 2024

Senal ME-220-CL Handleiding

21 November 2024

Senal ASM-4 Handleiding

21 November 2024

Senal CS-88 Handleiding

21 November 2024

Senal CSP-162 Handleiding

21 November 2024

Senal ASM-3 Handleiding

21 November 2024

Senal ASM-5 Handleiding

21 November 2024