Ultimaker 2+ Connect Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Ultimaker 2+ Connect (39 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 81 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/39
Ultimaker 2+ Connect
Installation and user manual
EN 10/2020 v1.0 Original instructions
Ultimaker 2+ Connect user manual 1
Table of contents
1. Safety and compliance
1.1 Safety messages 4
1.2 General safety information 4
1.3 Hazards 5
1.4 Regulatory information 6
2. Introduction
2.1 Main components 9
2.2 Specications 11
3. Installation
3.1 Unboxing 13
3.2 What's in the box? 14
3.3 Hardware installation 15
3.4 First setup 16
3.5 Firmware update 17
3.6 Install Ultimaker Cura 18
4. Operation
4.1 Touchscreen 20
4.2 Materials 21
4.3 Preparing a print with Ultimaker Cura 22
4.4 Printing with the Air Manager 24
4.5 Remove the print 25
4.6 Change the printer conguration 26
5. Maintenance
5.1 Update the rmware 28
5.2 Material handling and storage 28
5.3 Maintenance schedule 29
5.4 Replace the Air Manager lter 30
6. Troubleshooting
6.1 Error messages 32
6.2 Extrusion problems 32
6.3 Adhesion issues 33
6.4 Air Manager troubleshooting 34
7. Warranty
7.1 General 36
7.2 Conditions 36
7.3 Notication 37
7.4 Exclusions 37
7.5 Applicable law and competent court 37
Ultimaker 2+ Connect user manual 2
Disclaimer
This manual sets out the instructions on how to install and operate the Ultimaker 2+ Connect. Please read and
understand the contents of this installation and user manual carefully. Failure to read the manual may lead to
personal injury, inferior print results or damage to the Ultimaker printer or its peripherals. Always make sure that
anyone who uses this 3D printer knows and understands the contents of the manual to make the most out of
the Ultimaker printer.
Upon delivery of the product, installation shall be done in accordance with the instructions in this user manual. The
handling, storage, use, or disposal of the device are beyond our control and are for your sole responsibility. We do
not assume responsibility and expressly disclaim liability for loss, injuries, damage, or expense arising out of or in
any way connected with the handling, storage, use, or disposal of the product.
The information within this document has been collected and represented with great care and is considered
accurate. In case inconsistencies or inaccuracies are observed those are unintentional and Ultimaker welcomes to
be made aware of those. Submit your feedback to Ultimaker via ‘Submit a request’ at support.ultimaker.com.
Intended use
Ultimaker 3D printers are designed and built for fused lament fabrication with Ultimaker materials mainly within
a commercial, professional, or educational environment. The mixture of precision and speed makes Ultimaker 3D
printers very suitable for concept models, functional prototypes, and small series production.
The Ultimaker 2+ Connect, with its networking capabilities and new touchscreen, delivers single extrusion for
simple applications.
Although we achieved a very high standard in the reproduction of 3D models with the usage of Ultimaker Cura,
the user remains responsible to qualify and validate the application of the printed object for its intended use. This
is especially critical for applications in strictly regulated areas like medical devices and aeronautics. While being
an open material platform, the best results will be achieved with Ultimaker materials, as eort has been made to
match material properties with machine settings.
Product specificaties
| Merk: | Ultimaker |
| Categorie: | Printer |
| Model: | 2+ Connect |
Heb je hulp nodig?
Als je hulp nodig hebt met Ultimaker 2+ Connect stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Printer Ultimaker
31 Mei 2023
25 Mei 2023
22 April 2023
19 Februari 2023
17 Januari 2023
11 Januari 2023
12 November 2022
Handleiding Printer
- Printer HP
- Printer Sony
- Printer Samsung
- Printer Xiaomi
- Printer Panasonic
- Printer Epson
- Printer LG
- Printer Huawei
- Printer Canon
- Printer Honeywell
- Printer Olympus
- Printer Toshiba
- Printer Xerox
- Printer Brother
- Printer Builder
- Printer D-Link
- Printer Dell
- Printer Digitus
- Printer Dymo
- Printer Epson 7620
- Printer Frama
- Printer Fujifilm
- Printer Fujitsu
- Printer Ibm
- Printer Intermec
- Printer Kodak
- Printer Kogan
- Printer Konica Minolta
- Printer Kyocera
- Printer Lenovo
- Printer Lexmark
- Printer Minolta
- Printer Mitsubishi
- Printer MSI
- Printer Nec
- Printer Paxar
- Printer Polaroid
- Printer Primera
- Printer Renkforce
- Printer Ricoh
- Printer Roland
- Printer Royal Sovereign
- Printer Sagem
- Printer Seiko
- Printer Sharp
- Printer Star
- Printer Thomson
- Printer Tomy
- Printer Toshiba TEC
- Printer Triumph-Adler
- Printer Velleman
- Printer Zebra
- Printer Oce
- Printer Oki
- Printer Olivetti
- Printer Olympia
- Printer CSL
- Printer Argox
- Printer DTRONIC
- Printer Metapace
- Printer Citizen
- Printer Nilox
- Printer Approx
- Printer Custom
- Printer Bixolon
- Printer Brady
- Printer GoDEX
- Printer Testo
- Printer EC Line
- Printer Sawgrass
- Printer Pantum
- Printer DNP
- Printer TSC
- Printer Equip
- Printer StarTech.com
- Printer Fichero
- Printer GG Image
- Printer Posiflex
- Printer ZKTeco
- Printer Star Micronics
- Printer Datamax-O'neil
- Printer Panduit
- Printer Dascom
- Printer HiTi
- Printer Vupoint Solutions
- Printer Elite Screens
- Printer Phoenix Contact
- Printer Colop
- Printer Raspberry Pi
- Printer Evolis
- Printer Middle Atlantic
- Printer IDP
- Printer Fargo
- Printer Microboards
- Printer Tally Dascom
- Printer Nisca
Nieuwste handleidingen voor Printer
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024
2 December 2024