Tripp Lite T012-001-K Handleiding

Tripp Lite Niet gecategoriseerd T012-001-K

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite T012-001-K (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Owner’s Manual

Cable Tester with

Wire Tracker

Model: T012-001-K

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

15-11-220-9334E1.indd 1 12/9/2015 3:45:00 PM

Package Includes

Product Features

Wire Tracking

• Main Tester

• Remote Probe Unit

• RJ45 Jumper Cable

• RJ11 Jumper Cable

• Alligator Clip Adapter

• Headphones

• 9V Battery (x2)

• Owner’s Manual

• Multi-Function Kit allows for both cable testing and wire tracking

• Find a single RJ11, RJ45, or BNC cable within a group of cables

• Determine the location of a short or breakage in non-powered wires

• Perform wire mapping on RJ45 cables, detecting shorts and open wires

• LED light on Remote Probe Unit for use in dark areas

Notes:

• The volume button is used to ﬁne tune the tone generator. If you are having trouble with the

probe not honing in on a single cable, adjust the volume setting. When tracking a cable that has

power running through it, it is recommended to set the volume from 1-3. When tracking a non-

powered cable, set the volume from 6-8.

• The included headphones can be used when in a noisy environment to ensure you hear the

tone from the Remote Probe Unit.

• Flip the light switch on the side of the Remote Probe Unit to turn on the light for use in dark

areas.

1. If this is the ﬁrst time you are using the product, insert a 9V battery into the battery

compartment of the Main Tester and the Remote Probe Unit. Flip the switch on the

Main Tester to the position. The LED will ﬂash to indicate the Main Tester Scan Status

is ready for operation.

2. Connect the RJ11, RJ45, or BNC cable to be tracked to the corresponding port on

the Main Tester.

3. Flip the switch on the Remote Probe Unit to the position. The LED will Scan Power

illuminate to indicate the Remote Probe Unit is ready for operation.

4. Run the probe of the Remote Probe Unit along the group of cables until the tone

sounds, indicating you have found the desired cable.

15-11-220-9334E1.indd 2 12/9/2015 3:45:00 PM

Locating a Short or Breakage in a Non-Powered Cable

RJ45 Wire Mapping

Notes:

• Set the volume from 6-8 when locating a short or breakage.

• Locating a short or breakage can only be performed on a non-powered cable.

• The included headphones can be used when in a noisy environment to ensure you are hearing

the tone from the Remote Probe Unit.

• Flip the light switch on the side of the Remote Probe Unit to turn on the light for use in dark

areas.

1. Flip the switch on the Main Tester to the position. The LED will ﬂash to Scan Status

indicate the Main Tester is ready for operation.

2. Connect the included alligator clip adapter to the corresponding port on the Main

Tester.

• When locating a , connect both alligator clips to the bare wires on the cable short

being tested.

• When locating a , connect the red alligator clip to one of the bare wires, breakage

leaving the black alligator clip free.

3. Flip the switch on the Remote Probe Unit to the position. The LED will Scan Power

illuminate to indicate the Remote Probe Unit is ready for operation.

4. Run the probe of the Remote Probe Unit along the cable. The tone will sound,

indicating that the area where the probe is currently located is undamaged. Continue

running the probe along the cable until the tone stops, which will be the location of

the short or breakage.

1. Flip the switch on the Main Tester to the Test Verify position. The LED will ﬂash to

indicate the Main Tester is ready for operation.

2. Flip the switch on the Remote Probe Unit to the position. The LED will Scan Power

illuminate to indicate the Remote Probe Unit is ready for operation.

3. Connect RJ45 cable from the RJ45 port of the Main Tester to the RJ45 port of the

Remote Probe Unit.

4. The Pin LEDs on the Main Tester and Remote Probe Unit will illuminate per below.

When performing a Wire Mapping operation, pressing the button will change the Note: SET

speed at which the LEDs ﬂash.

• – When a UTP cable is properly wired, the LEDs on both units will Good Cable

ﬂash in sequence from 1 through 8. For a good STP cable, the LEDs will ﬂash in

sequence from 1 through 8, including G.

• – In the case of a short, the LED(s) of the pin(s) in which a short is present Short

will not illuminate on the Remote Probe Unit. The LEDs on the Main Tester unit will

all continue to illuminate.

• – In the case of an open pin, the LED(s) of the open pin(s) will remain off on Open

both the Main Tester and Remote Probe Unit.

15-11-220-9334E1.indd 3 12/9/2015 3:45:00 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	T012-001-K
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht verpakking:	550 g
Breedte verpakking:	246.9 mm
Diepte verpakking:	150.1 mm
Hoogte verpakking:	46 mm
Gebruikershandleiding:	Ja
Meegeleverde kabels:	LAN (RJ-45),Phone (RJ-11)
Land van herkomst:	China
Duurzaamheidscertificaten:	RoHS
Opbergetui:	Ja
(Buitenste) hoofdverpakking hoogte:	160 mm
(Buitenste) hoofdverpakking breedte:	480.1 mm
(Buitenste) hoofdverpakking brutogewicht:	6000 g
(Buitenste) hoofdverpakking lengte:	279.9 mm
Hoeveelheid per (buitenste) hoofdverpakking:	10 stuk(s)
Batterijen inbegrepen:	Ja
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332189919
Testtype:	Kortsluitingstesten
Ondersteunde aansluitingen:	BNC,RJ-11,RJ-45