Tripp Lite SRSWITCH Handleiding

Tripp Lite Niet gecategoriseerd SRSWITCH

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SRSWITCH (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Owner’s Manual

SmartRack™ Accessories

Model: SRSWITCH

1111 W. 35th Street, Chicago, IL 60609 USA

(773) 869-1234 • www.tripplite.com

WARRANTY

REGISTRATION:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

1 – Introduction 0 2

1-1 Parts List 2

1-2 Tools Required 2

2 – Important Safety Instructions 2

3 – SRSWITCH Installation 3

3-1 Mounting the Switch and Magnet to the Rack Enclosure 3

3-2 Wiring the Switch 3

4 – Connection to SNMPWEBCARD and ENVIROSENSE 4

5 – Warranty and Warranty Registration 4

2 – Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the products

described in this manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may

invalidate the warranty and cause property damage and/or personal injury.

1 – Introduction

1-1 Parts List

1-2 Tools Required

The SRSWITCH is designed to monitor rackmount enclosure door access and notify users when a door has been opened. The SRSWITCH must be used

together with the following Tripp Lite accessories: SNMPWEBCARD and ENVIROSENSE (both available separately).

A1 Switch (1)

A2 Magnet (1)

A3 #22 AWG cable - 6 ft. (1.8 m) (1)

A4 Cable ties (6)

A5 Adhesive cable tie holders (3)

Install in a controlled indoor environment, away from moisture, temperature extremes, ammable liquids and gasses, conductive contaminants, dust and •

direct sunlight.

Provide suitable grounding in accordance with all applicable electrical wiring regulations.•

Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support •

equipment or to signicantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a ammable anesthetic

mixture with air, oxygen or nitrous oxide.

Wire Cutters Wire Strippers Screwdriver

3 – SRSWITCH Installation

The switch and magnet are designed to be mounted at the top of a SmartRack Premium Rack Enclosure. Magnet should be mounted ush against the inside

edge of the Rack Enclosure door. Attach the switch to the outside of the Rack Enclosure cabinet and make sure both switch and magnet are in alignment.

The switch and magnet should be mounted on the side of the enclosure opposite the hinges.

Note: the switch and magnet do not need to make physical contact but should be no more than ¼ inch (6.35 mm) apart.

3-1 Mounting the Switch and Magnet to the Rack Enclosure

3-2 Wiring the Switch

The double-sided tape on both the switch and magnet allow you to mount

them to a rack enclosure without any drilling.

Mark the intended location of both the switch and the magnet.1.

Peel the paper backing off the adhesive strip attached to the back 2.

of the switch.

Place the switch in the desired location. Press rmly.3.

Repeat steps 2 and 3 to mount the magnet.4.

Before attaching the wire to the switch, use wire cutters to clip to 1.

desired length (if necessary).

Use wire strippers to cut back the covering of the two wires and remove 2.

a small amount of insulation from the end of each wire. (Do not cut

through the insulation into the wire itself.)

Twist the bare ends of the wire, place them under the head of each 3.

screw on the switch and then wrap the wire clockwise around the screw.

Tighten the screw by turning it clockwise.

Use the cable ties and adhesive cable tie holders (included) to secure 4.

the entire length of the wire.

Route the wire away from the switch and magnet and attach to one of 5.

the security inputs on the ENVIROSENSE (see Section 4-1).

Note: Make sure the wire is not pinched by any part of the rack

enclosure or its door.

Approximately 1 in. (25.4 mm)

Approximately 0.38 in. ( )9.7 mm

SmartRack Enclosure

(Front Door Open)

Magnet: Attaches to Door

SmartRack Enclosure

(Back Door Open)

MagnetSwitch

Right Wrong

Switch: Attaches to Cabinet

Magnet: Attaches to Door

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SRSWITCH
Kleur van het product:	Black, White
Breedte:	100 mm
Diepte:	24 mm
Hoogte:	33.5 mm
Gewicht verpakking:	230 g
Breedte verpakking:	100.1 mm
Diepte verpakking:	143 mm
Hoogte verpakking:	55.1 mm
Land van herkomst:	China
(Buitenste) hoofdverpakking hoogte:	303 mm
(Buitenste) hoofdverpakking breedte:	307.1 mm
(Buitenste) hoofdverpakking brutogewicht:	12250 g
(Buitenste) hoofdverpakking lengte:	522 mm
Hoeveelheid per (buitenste) hoofdverpakking:	50 stuk(s)
Code geharmoniseerd systeem (HS):	8536.50.9065
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332144772