Tripp Lite SRFILTER Handleiding

Tripp Lite Niet gecategoriseerd SRFILTER

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SRFILTER (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 96 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Introduction

Important Safety Instructions

Owner’s Manual

SmartRack® Enclosure Filter Kit

Model: SRFILTER

Español 3 • Français 5

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product

described in this manual. Failure to comply may invalidate the warranty.

• The instructions in this manual are for common rack and rack enclosure types and may not be appropriate for all mounting applications. You

must determine the ﬁtness of hardware and procedures before mounting. If hardware or procedures are not suitable for your application,

contact the manufacturer of your rack or rack enclosure for a solution.

• Before applying adhesive strips, measure carefully to assure proper alignment. SRFILTER kit comes ready to install in 48U rack enclosures.

Vertical hook-and-loop strips must be trimmed accordingly to accommodate 42U and 25U enclosures.

PROTECT YOUR INVESTMENT!

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SRFILTER Kit Beneﬁts:

• Prevents dust and particle buildup on equipment installed in a standard SmartRack Enclosure

• Facilitates hot-aisle / cold-aisle data center conﬁgurations

• Fully compatible with 25U, 42U and 48U SmartRack Enclosures

Parts List

A 20” L x 1.5” W horizontal hook-and-loop

strips (3 pieces)

B 40” L x 1.5” W vertical hook-and-loop

strips (4 pieces)

C 7/8” diameter circular hook-and-loop

pieces (12 pieces)

D Filter (1 piece)

Installation Procedure

1 Remove self-adhesive backing strips and

install the 3 horizontal hook-and-loop

strips to the top, middle and bottom non-

perforated sections inside the SmartRack

door frame.

2 Following the same procedure, install the

4 vertical hook-and-loop strips to the non-

perforated inside frame of the SmartRack

door.

The SRFILTER kit is prefabricated for the Note:

vertical strips to ﬁt a 48U enclosure. For 42U

and 25U enclosures, measure ﬁrst and cut

accordingly before removing the self-adhesive

backing.

3 Remove the self-adhesive backing and

install the 12 circular hook-and-loop pieces

in a staggered pattern on the perforated

portion of the door.

Be sure to space the pieces appropriately Note:

to ensure complete coverage of the door to

enable a snug ﬁt.

4 Install the ﬁlter on the inside of the door

along all the hook-and-loop pieces.

The ﬁlter is also prefabricated to ﬁt 48U Note:

enclosures. For 42U and 25U enclosures, be

sure to measure and cut accordingly before

installation.

Standard Installation

Warranty Registration

When a ﬁlter becomes dirty or worn from use, be sure to replace it. Hook-and-loop pieces can remain attached to door, with no need for

replacement.

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite

product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment

or to signiﬁcantly affect its safety or effectiveness is not recommended.

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice.

Introducción

Instrucciones de Seguridad Importantes

Manual del Propietario

Juego de Filtros para Gabinetes

SmartRack®

Modelo: SRFILTER

English 1 • Français 5

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante la instalación y operación del producto descrito

en este manual. Su inobservancia puede invalidar la garantía.

• Las instrucciones de este manual son para los tipos comunes de racks y gabinetes de racks y pueden no ser apropiados para todas las

aplicaciones de montaje. El usuario debe determinar si los herrajes y los procedimientos son adecuados antes de efectuar la instalación.

Si los herrajes o los procedimientos no son adecuados para su aplicación, contacte el fabricante de su rack o gabinete para hallar una

solución.

• Haga mediciones cuidadosas antes de aplicar las cintas adhesivas para asegurar la correcta alineación. El juego SRFILTER viene listo para

instalarse en gabinetes de 48U. Las tiras verticales de “gancho y bucle” necesitaran recortarse y ajustarse para colocarlas en los gabinetes

de 42U y 25U.

1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support

Beneﬁcios del juego SRFILTER:

• Previene la acumulación de polvo y partículas en los equipos instalados en un gabinete SmartRack estándar

• Facilita las conﬁguraciones de centros de datos con pasillos calientes / pasillos fríos

• Plenamente compatible con los Gabinetes SmartRack de 25U, 42U y 48U

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SRFILTER
Kleur van het product:	Wit
Gewicht:	910 g
Breedte:	508 mm
Diepte:	165.1 mm
Hoogte:	165.1 mm
Gewicht verpakking:	820 g
Breedte verpakking:	276.9 mm
Diepte verpakking:	391.2 mm
Hoogte verpakking:	101.6 mm
Land van herkomst:	China
Compatibiliteit:	25U, 42U, 45U, 48U
(Buitenste) hoofdverpakking hoogte:	327.7 mm
(Buitenste) hoofdverpakking breedte:	543.6 mm
(Buitenste) hoofdverpakking brutogewicht:	4310 g
(Buitenste) hoofdverpakking lengte:	635 mm
Hoeveelheid per (buitenste) hoofdverpakking:	6 stuk(s)
Code geharmoniseerd systeem (HS):	5911.90.0080
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332148879