Tripp Lite SRCABLETRAY Handleiding

Tripp Lite Niet gecategoriseerd SRCABLETRAY

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SRCABLETRAY (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Owner’s Manual

WARRANTY

REGISTRATION

Visit www.tripplite.com/warranty

today to register the warranty for

your new Tripp Lite product. You’ll be

automatically entered into a drawing for a

chance to win a FREE Tripp Lite product!

SmartRack™ Accessories

Models: SRCABLETRAY, SRCABLETRAYEXP

1 – Introduction

3 – SRCABLETRAY Installation

1-2 Tools Required

4-1 One Expansion Section

5 – Storage and Service

1-1 Parts List

4 – SRCABLETRAYEXP Installation

2 – Important Safety Instructions

4-2 Two Expansion Sections

6 – Warranty and Warranty Registration

1111 W. 35th Street, Chicago, IL 60609 USA

+1.773.869.1234 • www.tripplite.com

1 – Introduction

2 – Important Safety Instructions

SRCABLETRAY provides roof-mounted cable routing and power/data cable segregation for Tripp Lite’s SmartRack Enclosures.

SRCABLETRAYEXP provides vertical expansion for SRCABLETRAY. (SRCABLETRAY also provides secure mounting points for Tripp

Lite’s SRCABLELADDER accessory, sold separately. SRCABLELADDER allows cable bundles to span aisles and/or spaces between

enclosures. See the SRCABLELADDER manual for more information.)

• Install in a controlled indoor environment, away from moisture, temperature extremes, ﬂ ammable liquids and gasses, conductive

contaminants, dust and direct sunlight.

• Provide suitable grounding in accordance with all applicable electrical wiring regulations.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life

support equipment or to signiﬁ cantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a

ﬂ ammable anesthetic mixture with air, oxygen or nitrous oxide.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the products described in this

manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may invalidate the warranty and

cause property damage and/or personal injury.

• Phillips Screwdriver

• 13 mm Open-End Wrench or Crescent Wrench (For SRCABLETRAY installation only.)

If anything is missing, call Tripp Lite for assistance at +1.773.869.1234. Note: SRCABLETRAY and SRCABLETRAYEXP are sold separately.

SRCABLETRAY

Trough Section (1)

Support Sections (2)

#8-32 x 1/4 Phillips Screws (8)

M6 Lock Washers (4)

M6 Hex Nuts (2)

24-inch Ground Cable (1)

SRCABLETRAYEXP

Expansion Sections (2)

#8-32 x 1/4 Phillips Screws (8)

1-1 Parts List

1-2 Tools Required

A1 A2

3 – SRCABLETRAY Installation

Note: You can remove the roof panel to aid installation, but this step is not required.

Assemble the cable tray by attaching the support sections A to

the trough section B with the included screws. Note: The support

sections should be attached inside the ﬂ anges of the trough

section, not outside.

Insert the tabs C at one side of the cable tray into the matching

roof panel slots D. (Several sets of slots are compatible, allowing

you to adjust the cable tray’s position to match your preference.)

Compress the unattached cable tray support section A until you

can insert the remaining tabs E into the matching roof panel

slots F. When you release pressure from the cable tray support

sections, they will expand to provide a secure ﬁ t.

Use the included hex nut G and lock washers H to connect one

end of the included ground cable I to a grounding post J at

the corner of the cable tray. Connect the other end of the ground

cable to the metal frame of the rack enclosure. (Follow the ground

wires connected to the rack enclosure’s doors to locate several

convenient ground connection points on the frame.)

3 4

4 – SRCABLETRAYEXP Installation

Note: You must install SRCABLETRAY before installing SRCABLETRAYEXP. SRCABLETRAYEXP includes two expansion sections; you may

install one or both, depending on your needs.

4-1 One Expansion Section

Attach the expansion section A to the cable tray B with the

included screws.

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SRCABLETRAY
Kleur van het product:	Zwart
Gewicht:	4080 g
Breedte:	312.9 mm
Diepte:	537 mm
Hoogte:	116.8 mm
Gewicht verpakking:	4580 g
Breedte verpakking:	312.4 mm
Diepte verpakking:	553.7 mm
Hoogte verpakking:	121.9 mm
Land van herkomst:	China
Duurzaamheidscertificaten:	RoHS
(Buitenste) hoofdverpakking hoogte:	574 mm
(Buitenste) hoofdverpakking breedte:	327.7 mm
(Buitenste) hoofdverpakking brutogewicht:	19230 g
(Buitenste) hoofdverpakking lengte:	513.1 mm
Hoeveelheid per (buitenste) hoofdverpakking:	4 stuk(s)
Code geharmoniseerd systeem (HS):	7326.90.8688
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332140781