Tripp Lite SmartRack SRW12UDP Handleiding

Tripp Lite Niet gecategoriseerd SmartRack SRW12UDP

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SmartRack SRW12UDP (36 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 74 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/36
Table of Contents
1. Important Safety Instructions 2
2. Overview 2
3. Feature Identification 3
4. Enclosure Installation 4
4.1 Preparation 4
4.2 Unpacking 4
4.3 Ground Connection 4
5. Enclosure Configuration 5
5.1 Door Locks 5
5.2 Cable Access & Management 5
5.3 Reversing the Enclosure 5
5.4 Mounting Rails 6
5.5 Adjusting Mounting Rail Depth 6
6. Wall Mounting the Enclosure 6
7. Equipment Installation 7
7.1 Installing or Removing Cage Nuts 7
7.2 Alternate Mounting: 8
Tapped Hole Mounting Rail
8. Storage and Service 9
9. Warranty and Product Registration 9
Español 10
Français 19
 28
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $50 value!
www.tripplite.com/warranty
Non-Swinging Wall-Mounted
SmartRack® Enclosures
Applies to Model Series: SRWxxU
(Agency Series Number: AG-00E9)
Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All trademarks are the sole property of their respective owners.
2
1. Important Safety Instructions
2. Overview
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual.
Failure to comply may invalidate the warranty and cause property damage or personal injury.
• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive
contaminants, dust and direct sunlight.
• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation
openings of the enclosure.
• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a
mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container.
• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.
• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.
• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible.
• Install the enclosure in a structurally sound area capable of handling the load, or on a level floor that is able to bear the weight of the enclosure, all
equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be installed nearby.
• For permanent wall mounting, be sure to securely fasten the enclosure to the building structure before operation.
• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.
• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product damage
that will void the warranty.
• Do not reship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet (“SP1” models only). The
combined weight of the enclosure and installed equipment must not exceed the load capacity of the pallet. Tripp Lite is not responsible for any
damage that occurs during reshipment.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support
equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Non-swinging wall-mounted SmartRack enclosures accommodate all standard 19-inch rackmount equipment, regardless of vendor, and ship fully
assembled for quick and easy deployment. They feature adaptable, heavy-duty cabinets in various heights.
Non-swinging wall-mounted SmartRack enclosures have variable mounting depths, ideal for servers. The cabinets include quick-release doors and side
panels for convenient maintenance. Front access doors are reversible for installation flexibility. Front door and side panels are lockable. An optional
rolling caster kit (SRCASTER) is available for easy maneuvering of enclosures.
3
3. Feature Identification
1 Front Door
2 Horizontal Rails
3 Vertical Mounting Rails
4 Removable Cable Access Hole Cover
5 Vents
6 Locking/Removable Side Panels
7 Mounting Notches (found on the enclosure’s back panel)
8 Mounting Plate (separate piece)
9 Mounting Plate Hooks
Model SRW6U is shown. The other models have similar features, with the only differences being rack height and depth.
12
2
3
3
4
455
6
7
8
9
4
4.2 Unpacking
4.3 Ground Connection
All parts of the enclosure are grounded to the frame of the enclosure. Use the enclosure’s front or
rear threaded grounding point A and an M6 screw (included) to connect the frame of the enclosure
directly to your facility’s earth ground connection with an 8 AWG (3.264 mm) wire. Route the
ground wire under the enclosure’s frame to ensure unhindered door operation. Warning: Attach
each enclosure to earth ground separately. Do not use the enclosure without an earth
ground connection.
Use at least two people to unpack the enclosure.
Never extend more than one component from the enclosure at a time.
Warning: Never attempt to lift or install without adequate help.
Do not try lifting the enclosure alone.
1 Move shipping pallet to a firm, level surface.
2 Open box and remove the four foam protectors. Save all packing materials for later use unless you are certain they will not be required. corner
Packing materials are recyclable.
3 With one person on each side, carefully lift the enclosure out of the box and place on a firm, level surface.
4 Examine the enclosure for any damage or loose parts. Confirm all parts are present. If anything is missing or damaged, contact Tripp Lite for
assistance. Do not attempt to use the enclosure if it has been damaged.
4. Enclosure Installation
Caution! Read All Instructions and Warnings Before Installation!
Warning: Rack enclosures can be extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance.
Use extreme caution when handling the enclosure and be sure to follow all handling and installation instructions. Do not
attempt to install equipment without first stabilizing the enclosure.
4.1 Preparation
The enclosure must be installed in a structually sound area that is able to bear the weight of the enclosure, all the equipment that will be installed in
the enclosure and any other enclosures and/or equipment that will be installed nearby. Before unpacking the enclosure, you should transport the
shipping container closer to the final installation location to minimize the distance you will need to move the unit after the protective packaging has
been removed. If you plan to store the enclosure for an extended period before installation, follow the instructions in the Storage and Service
section.
You need several tools:
• Level
• Phillips-head screwdriver
• Appropriate tools for wall mounting
You also need the following hardware:
• Appropriate hardware for wall mounting (not included)
EARTH
GROUND
A
6
5. Enclosure Configuration continued
6. Wall Mounting the Enclosure
5.4 Mounting Rails
5.5 Adjusting Mounting Rail Depth
The enclosure comes with mounting rails that have both square and tapped holes for mounting rack
equipment. To install equipment, use the included cage nuts and other hardware. (section 7.1 for
installation of cage nuts.) Warning: Be sure to have the enclosure securely mounted to
the wall, or in its final position on the floor, before mounting any equipment inside.
Also be sure to have all the right adjustments on your rails before mounting
equipment. (See below for Adjusting Mounting Rail Depth.)
Warning: Do not attempt to adjust rails while equipment is installed in the enclosure.
Do not attempt to use rails without screws installed. (2 per rail.)
The 2 mounting rails are pre-installed to accommodate different mounting depths, depending on
the model. Do not adjust the mounting rails unless your equipment requires a different mounting
depth. The front and rear sets of rails can be adjusted independently in 1/4-inch (6mm)
increments.
1 Each rail is connected to the enclosure with 2 screws and 2 cage nuts: 1 set in the upper
corner and another in the lower corner. Using a Phillips-head screwdriver, remove the screws
that fasten the rails to the enclosure.
2 Move cage nuts to the desired depth and reinstall.
3 Slide the mounting rails to the desired depth and reattach them using the screws you removed in
Step 1.
Warning: Do not attempt to mount the enclosure to the wall with equipment in the enclosure.
Note: Enclosure must be installed by a qualified technician. Before mounting, use a level and tape
measure to position your mounting area precisely. Use appropriate fasteners (not included) to secure the
enclosure to the wall. Use suitable mounting means when installing to cinder block, concrete, drywall or
wood studs. Warning: The supporting surface must be able to safely support the combined load of
the equipment and all attached hardware and components. For the actual weight, size and load
capacity of the enclosure, view the product specifications and other support resources at
www.tripplite.com/support.
1 Using user-supplied hardware, attach the mounting plate to a wall or other suitable mounting
surface. Each mounting hole can accommodate an M8 or 5/16” bolt and the holes are spaced
16" apart to accommodate standard stud placement as reflected in the diagram. Note: When
mounting the mounting plate to the wall, be sure the three mounting hooks are facing outwards
and away from the wall.
2 After the mounting plate has been securely attached to the mounting surface, hang the
enclosure’s three mounting notches onto the three mounting hooks on the plate attached to the
wall. The notches will fit over the hooks and the enclosure should slide down onto the hooks
until secure. Note: Mounting notches exist on both the upper and lower rails of the back panel.
This allows for mounting in the standard or reversed positions.
3 After the mounting plate has been secured and the enclosure hung properly, secure the
enclosure to the mounting plate by installing the three supplied screws in the holes on the
mounting hooks as shown.
16”
2.75”
2.75”
16”
AA
BB
C
C
1
2
3
1
2
3
7
7. Equipment Installation
7.1 Installing or Removing Cage Nuts
Warning: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first towards the bottom of
the enclosure. Install equipment starting from the bottom of the enclosure and proceed toward the top of the enclosure - never
the reverse. If using sliding equipment rails, be careful when extending the rails. Do not extend more than one set of sliding
equipment rails at one time. Avoid extending sliding equipment rails near the top of the enclosure.
Note: The unit comes with two different kinds of screws for equipment installation, black and silver. Use the black mounting screws if you are securing your
equipment to the square hole side of the mounting rail. Use the silver screws if you are securing your equipment to the tapped hole side of the mounting rail.
Note: The square holes in the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit includes the space
occupied by the numbered hole and the holes directly above and below.
To Remove Cage Nuts, Reverse Steps 1-3
Note: You may wish to use a cage nut tool (user-supplied) to aid cage nut installation and removal.
WARNING: The flanges of the cage nuts should engage the sides of the square opening in the rail, not the top and bottom. Follow
the instructions in your equipment documentation to ensure proper installation of your equipment.
1 Locate the numbered square openings in the mounting rails where you plan to install your
equipment. You will install cage nuts (included) into the square openings in order to provide an
attachment point for the mounting screws (included). Note: Consult your equipment
documentation to determine how many cage nuts will be required and where they will need to
be installed.
2 From the inside of the mounting rail, insert one of the flanges of the cage nut through the
square opening. Press it against the side of the square opening. Each flange should engage one
side of the square opening, not the top or bottom.
3 Compress the cage nut at the sides slightly to allow the remaining flange to fit through the
square opening. When the cage nut is properly installed, both flanges will protrude through the
square opening and will be visible on the outer surface of the mounting rail. Repeat steps 1-3
until all required cage nuts are installed.
4 After installing the required cage nuts, use the included black mounting screws and cup washers
to secure your equipment to the rack rail. Place the cup washers between the screws and the
equipment mounting brackets.
Note: Your equipment may also include mounting hardware. Read the mounting instructions that came
with your equipment before installing your equipment.
2
3
2
2
2
1
23 23
24
24
1 Rack Unit
1
2
3
4
8
7. Equipment Installation continued
7.2 Alternate Mounting: Tapped Hole Mounting Rail
Warning: Do not attempt to adjust rails while equipment is installed in the enclosure. Do not attempt to use rails without screws
installed. (2 per rail.)
The 2 mounting rails are pre-installed for securing equipment using the square hole side of the mounting rail. To switch to the tapped hole side of the
mounting rail, follow the steps below:
1 Each rail is connected to the enclosure with 2 screws: 1 in the upper corner and another in the
lower corner. Using a Phillips-head screwdriver, remove the screws that fasten the rails to the
enclosure.
2 Switch the rail locations. Ensure the tapped hole side of each rail is facing the front door.
3 Reattach the mounting rails.
4 Use the included silver mounting screws to secure your equipment to the rack rail. Place the
cup washers between the screws and the equipment mounting brackets.
Note: Your equipment may also include mounting hardware. Read the mounting instructions that
came with your equipment before installing.
1
3
Upper Rail
Upper Rail
Lower Rail
Lower Rail
2
2
4
9
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a
period of 5 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair
or replace the product, at its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES
NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD
SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow
limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since
individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these
devices for any specific application.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE
Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
8. Storage and Service
9. Warranty and Product Registration
Storage
The enclosure should be stored in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses,
conductive contaminants, dust and direct sunlight. Store the enclosure in its original shipping container if possible.
Service
Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service Programs are also
available from Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service, follow these steps:
1. Review the installation and operation procedures in this manual to insure that the service problem does not originate from a misreading of the
instructions.
2. If the problem continues, do not contact or return the product to the dealer. Instead, visit www.tripplite.com/support.
3. If the problem requires service, visit www.tripplite.com/support and click the “Request Return (RMA)” link. From here you can request a Returned
Material Authorization (RMA) number, which is required for service. This simple on-line form will ask for your unit’s model and serial numbers, along
with other general purchaser information. The RMA number, along with shipping instructions will be emailed to you. Any damages (direct, indirect,
special or consequential) to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center are not covered under
warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA number
on the outside of the package. If the product is within its warranty period, enclose a copy of your sales receipt. Return the product for service using
an insured carrier to the address given to you when you request the RMA.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
11
1. Instrucciones de Seguridad Importantes
2. Vista General
CONSERVE ESTAS INSTRUCCIONES
Este manual contiene instrucciones y advertencias que deben observarse durante la instalación y operación del producto descrito en este manual. El no
hacerlo puede invalidar la garantía y causar daños a la propiedad o lesiones personales.
• Mantenga el gabinete en un entorno interior controlado lejos de humedad excesiva, temperaturas extremas, líquidos y gases inflamables,
contaminantes conductores, polvo o luz solar directa.
• Deje un espacio adecuado al frente y detrás del gabinete para una ventilación adecuada. No bloquee, cubra o inserte objetos en las aberturas de
ventilación externa del gabinete.
• El gabinete es extremadamente pesado. Tenga cuidado al manejar el gabinete. No intente desempacarlo, moverlo o instalarlo sin ayuda. Use un
dispositivo mecánico como un montacargas o gato para tarimas para mover el gabinete en el contenedor de embarque.
• No coloque objeto alguno sobre el gabinete, especialmente recipientes de líquidos y no intente apilar los gabinetes.
• Inspeccione el contenedor de embarque y el gabinete para detectar daños en el embarque. No use el gabinete si está dañado.
• Deje el gabinete en el contenedor de embarque hasta que haya sido movido tan cerca a su ubicación final como sea posible.
• Instale el gabinete en un área estructuralmente firme, capaz de manejar la carga o sobre una piso nivelado que sea capaz de soportar el peso del
gabinete, todo el equipo que se instale en el gabinete y otros gabinetes y/o equipo que se instalen cerca.
• Para instalación permanente en la pared, asegúrese de fijar firmemente el gabinete a la estructura del edificio antes de la operación.
• Tenga cuidado al cortar los materiales de empaque. El gabinete podría ser arañado, causando daños no cubiertos por la garantía.
• Guarde todo el material de empaque para uso posterior. El reempacar y embarcar el gabinete sin los materiales de empaque originales puede
causar daños al producto que anulen la garantía.
• No reembarque el gabinete con equipo adicional a menos que el gabinete haya sido embarcado con una tarima especial anti-impacto (solo
modelos “SP1”). El peso combinado del gabinete y el equipo instalado no debe exceder la capacidad de la tarima. Tripp Lite no es responsable por
daño alguno que ocurra durante el reembarque.
• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo pueda consecuentemente causar la
falla del equipo de soporte de vida o afectar significativamente su seguridad o efectividad. No use este equipo en presencia de una mezcla
inflamable de anestésicos con aire, oxígeno u óxido nitroso.
Los gabinetes SmartRack no giratorios para Instalación en la pared acomodan todo el equipo para instalación en rack estándar de 19", sin importar el
proveedor y se embarcan completamente ensamblados para una instalación rápida y fácil. Cuentan con gabinetes adaptables de servicio pesado en
diversas alturas.
Los gabinetes SmartRack no giratorios para instalación en la pared tienen profundidades de instalación variables, ideales para servidores. Para
comodidad en el mantenimiento, los gabinetes incluyen puertas y paneles laterales de liberación rápida. Para flexibilidad de instalación, las puertas de
acceso frontal son reversibles. La puerta frontal y los paneles laterales pueden cerrarse con cerradura. Para fácil movilidad de los gabinetes está
disponible un juego opcional de ruedas (SRCASTER).
13
4.2 Desempacado
4.3 Conexión a Tierra
Todas las partes del gabinete se conectan a tierra con el marco del gabinete. Use el punto roscado
de conexión a tierra frontal o posterior A y un tornillo M6 (incluido) para conectar el marco del
gabinete directamente a la conexión de tierra de su instalación con un cable calibre 8 AWG
|(3.264 mm). Conduzca el cable de tierra bajo el marco del gabinete para asegurar la operación
sin obstáculos de la puerta. Advertencia: Conecte cada gabinete por separado a la conexión
a tierra física. No use el gabinete sin una conexión a tierra física.
Utilice al menos dos personas para desempacar el gabinete.
Nunca extienda más de un componente del gabinete a la vez.
Advertencia: Nunca intente levantar o instalar sin la ayuda adecuada.
No trate de levantar el gabinete solo.
1 Mueva la tarima de embarque a una superficie firme y nivelada.
2 Abra la caja y retire los cuatro protectores de las esquinas. Guarde todos los materiales de empaque para uso posterior a menos que esté seguro
de no necesitarlos. Los materiales de empaque son reciclables.
3 Con una persona en cada lado, levante cuidadosamente el gabinete fuera de la caja y colóquelo sobre una superficie firme y nivelada.
4 Examine el gabinete para detectar cualquier daño o parte suelta. Confirme que estén todas las partes. Si falta algo o está dañado, póngase en
contacto con Tripp Lite para solicitar apoyo. No intente usar el gabinete si p13-ha sido dañado.
4. Instalación del Gabinete
¡Precaución!
¡Lea todas las instrucciones y advertencias antes de la instalación!
Advertencia: Los gabinetes de rack son extremadamente pesados. No intente desempacar, mover o instalar el gabinete si
ayuda. Tenga extremo cuidado al manejar el gabinete y cerciórese de seguir todas las instrucciones de instalación. No intente
instalar el equipo sin estabilizar primero el gabinete.
4.1 Preparación
El gabinete debe instalarse en un área estructuralmente firme que sea capaz de soportar el peso del gabinete, todo el equipo que se instale en el
gabinete y otros gabinetes y/o equipo que se instalen cerca. Antes de desempacar el gabinete, debe transportar el contenedor de embarque lo más
cerca posible a la posición de instalación final para minimizar la distancia que necesite mover la unidad después de haber retirado el empacado
protector. Si planea almacenar el gabinete por un período prolongado antes de la instalación, siga las instrucciones en la sección Almacenamiento y
Servicio.
Necesita varias herramientas:
• Nivel
• Desarmador con punta Phillips
• Herramientas apropiadas para instalación en pared:
Necesita además los siguientes accesorios:
• Accesorios apropiados para instalación en pared
(no incluidos)
A
TIERRA
FÍSICA

Product specificaties

Merk: Tripp Lite
Categorie: Niet gecategoriseerd
Model: SmartRack SRW12UDP

Heb je hulp nodig?

Als je hulp nodig hebt met Tripp Lite SmartRack SRW12UDP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Tripp Lite

Tripp Lite

Tripp Lite U452-003 Handleiding

31 Maart 2025
Tripp Lite

Tripp Lite B064-032-02-IPH Handleiding

4 Maart 2025
Tripp Lite

Tripp Lite NetDirector B064-032-01-IPH Handleiding

4 Maart 2025
Tripp Lite

Tripp Lite U352-000-MD-AL Handleiding

4 Maart 2025
Tripp Lite

Tripp Lite U352-06N-SD Handleiding

4 Maart 2025
Tripp Lite

Tripp Lite U452-000-SD-A Handleiding

4 Maart 2025
Tripp Lite

Tripp Lite SmartRack SRIN4101010 Handleiding

14 Januari 2025
Tripp Lite

Tripp Lite SmartRack SRH42UWDP54WD8 Handleiding

14 Januari 2025
Tripp Lite

Tripp Lite SmartRack SRH48UWDP54WD8 Handleiding

14 Januari 2025
Tripp Lite

Tripp Lite SmartRack SRH48UWDPWD8 Handleiding

14 Januari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic Lumix DMW-AC11 Handleiding

9 April 2025
Soundstream

Soundstream VRN-64HBL Handleiding

9 April 2025
MOZA

MOZA SR-P Handleiding

9 April 2025
Creality3D

Creality3D Ender-3 S1 Pro Handleiding

9 April 2025
Act

Act AC6020 Handleiding

9 April 2025
BlueBuilt

BlueBuilt BBMA2M Handleiding

9 April 2025
Act

Act AC6015 Handleiding

9 April 2025
Diamond Audio

Diamond Audio MSHD9813SG Handleiding

9 April 2025
Daikin

Daikin ETVZ12S18EJ6V Handleiding

9 April 2025
Daikin

Daikin FXFQ80AVEB Handleiding

9 April 2025