Tripp Lite SMARTINT1500 Handleiding

Tripp Lite Niet gecategoriseerd SMARTINT1500

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite SMARTINT1500 (28 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

Owner’s Manual

SmartPro® INT

450-1500 VA

Intelligent, Line-Interactive

UPS Systems (230V)

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

® is a registered trademark of Tripp Lite.

Safety: 2

Quick Installation 3

Basic Operation 4

Storage & Service 6

Speciﬁcations 6

Español 7

Français 14

Русский 21

18-08-320-932202.indb 1 5/13/2019 2:55:51 PM

Safety

This manual contains important instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, keep the indoor temperature between 0° C and 40° C (between

32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug.

Do not use adapters that eliminate the UPS’s ground line.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must

provide clean, ﬁltered computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or

failure of a Tripp Lite UPS System could cause failure or signiﬁcantly alter the performance

of a life-support device.

• Do not connect surge suppressors to the output of your UPS. This may damage your UPS

and will void both the surge suppressor and UPS warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any reason.

There are no user-serviceable parts inside.

• Battery replacement must be performed by qualiﬁed service personnel. Because the

batteries present a risk of electrical shock and burn from high short-circuit current, qualiﬁed

service personnel should observe proper precautions: Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles and replace the existing

batteries with the same number and type of new batteries (Sealed Lead-Acid). Do not open

the batteries. Do not short or bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements. Do not

dispose of the batteries in a ﬁre.

• Do not attempt to add external batteries.

18-08-320-932202.indb 2 5/13/2019 2:55:51 PM

Quick Installation

1 Connect your computer to the UPS, and

the UPS to an electrical outlet.

1. Unplug your computer’s power cord from both

your AC outlet and your computer’s AC input.

2. Insert the female plug of the power cord that

came with your UPS A into your computer’s AC

input. Insert the UPS cord’s male plug into any of

your UPS’s female output receptacles.

3. Insert the female plug of your computer’s cord

B into your UPS’s AC input. Insert the male plug

of your computer’s cord into your AC outlet.

2 Plug your equipment into your UPS.

Your UPS is designed to support only computer

equipment. You will overload your UPS if you connect

household appliances, laser printers or surge

suppressors.

Cords and receptacle adapters are available

from Tripp Lite to accommodate most outlet

conﬁgurations. If rewiring is necessary, refer to the

Wire Color-Code Chart at the bottom of the page.

–Optional DB9 Connection*–

Using Tripp Lite cable, connect the serial port of

your computer to the serial port of your UPS. Load

software and run installation program appropriate to

your operating system.

*Your UPS will function properly without this connection.

3 Turn your UPS ON.

Set the System Enable Switch (UPS back panel) to

“ON” (or “ENABLE/I”) 3a. This switch activates the

battery charger and microprocessor. The

“ ” light will ﬂash until you engage the ON/Standby

Switch to activate the “ON” mode.

Engage the momentary ON/Standby Switch (UPS

front panel) and release it to activate the “ON” mode

and supply power to the UPS receptacles 3b .

Wire Color Wire 1 Wire 2 Wire 3

American Black White Green

European Brown Blue Green/Yellow

Wire Reference Wire 1 Wire 2 Wire 3

American Line 1 Neutral Ground

European Line 1 Line 2 or Neutral Ground

Black Brown

White Blue

Green Green/

Yellow

AMER EURO

18-08-320-932202.indb 3 5/13/2019 2:55:53 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SMARTINT1500
Kleur van het product:	Blue, White
Gewicht:	17510 g
Breedte:	190.5 mm
Diepte:	235 mm
Hoogte:	323.8 mm
Gewicht verpakking:	18280 g
Breedte verpakking:	284.5 mm
Diepte verpakking:	332.7 mm
Hoogte verpakking:	431.8 mm
Materiaal behuizing:	Polycarbonaat (PC)
LED-indicatoren:	Ja
Vormfactor:	Tower
Land van herkomst:	China
Certificering:	UL1778, CSA, CE, GOST, SASO, IRAM
Interface:	DB9
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS
Uitgangsvermogen:	940 W
Accu/Batterij oplaadtijd:	4 uur
Temperatuur bij opslag:	-15 - 50 °C
Stroomspanning bescherming:	Over voltage, Under voltage
Frequentie:	50/60 Hz
Power factor:	0.6
Seriële poort(en):	2
Stekker:	C14 stekker
Efficientie:	94 procent
(Buitenste) hoofdverpakking hoogte:	431.8 mm
(Buitenste) hoofdverpakking breedte:	284.5 mm
(Buitenste) hoofdverpakking brutogewicht:	18280 g
(Buitenste) hoofdverpakking lengte:	332.7 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Surge energy rating:	480 J
Aantal AC uitgangen:	6 AC-uitgang(en)
Stopcontacttypes:	C13 stekker
Stroom (max.):	10 A
Output power capacity:	1.5 kVA
Ingang operation voltage (min):	- V
Ingang operation voltage (max):	- V
Uitgang operation voltage (min):	220 V
Uitgang operation voltage (max):	240 V
UPS-topologie:	Line-interactive
Aantal input fases:	1
Typische backup tijd op halve lading:	20 min
Typische backup tijd op volledige lading:	7 min
Hot-swap batterij:	Ja
Uitgangsspanningsregeling:	-15, +8 procent
EMI/RFI geluidsfiltering:	Ja
Golfvorm:	Sinus
Koude start:	Ja
Automatic Voltage Regulation (AVR):	Ja