Tripp Lite Protect It! TLP606SSTELB Handleiding

Tripp Lite Niet gecategoriseerd Protect It! TLP606SSTELB

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite Protect It! TLP606SSTELB (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

www.tripplite.com/support

Installation 2

FCC Part 68 Notice 3

Lifetime Limited Warranty 3

Ultimate Lifetime Insurance Policy 4

Protect It!™

Surge Suppressors

Español 5

™ is a trademark of Tripp Lite.

Warranty Registration 4

WARRANTY

REGISTRATION:

to win a FREE Tripp Lite product—

www.tripplite.com/warranty

Français 9

Important Safety Instructions 2

201010194 93-2666.indd 1 11/12/2010 9:36:52 AM

SAVE THESE INSTRUCTIONS

CAUTION! DO NOT connect to an ungrounded outlet. DO NOT use with 2-wire extension

cords or adapters. This surge suppressor is designed for indoor use only. Install the surge

suppressor away from heat-emitting appliances such as radiators or heat registers. Do not

install where excessive moisture is present. Do not plug extension cords into it. Never install

electrical, telephone, network or coaxial wiring during a lightning storm. Do not drill into any part

of the housing or open the housing for any reason. There are no user-serviceable parts inside.

Important Safety Instructions

• Use of this equipment in life support applications where failure of this equipment can reasonably be

expected to cause the failure of the life support equipment or to significantly affect its safety or

effectiveness is not recommended. Do not use this equipment in the presence of a flammable

anesthetic mixture with air, oxygen or nitrous oxide.

Installation

Mount Your Surge Suppressor (Optional Installation. Available on Select Models Only): If

desired, mount your surge suppressor on a wall or other sturdy, vertical surface. However, you must

mount the surge suppressor prior to connecting your equipment. Place a sheet of paper over the surge

suppressor’s mounting holes and mark their centers with a push pin. Next, place this template over the

desired area and mark with the push pins. Install screws (user supplied) into the marks until ¼ in. (0.6

cm) of the screw heads are exposed. Mount the surge suppressor over the screw heads and slide into

place.

Connect Your Surge Suppressor to the AC Power Line: Plug the surge suppressor’s power cord

into a standard, 3-wire grounded 120V AC outlet.

Turn Your Surge Suppressor ON: Press the surge suppressor’s power switch to “ON” or “RESET”

(depending on model). Select models feature an illuminated switch.

Check Your Surge Suppressor’s Diagnostic Indicator Lights (Available on Select Models Only):

If your surge suppressor features diagnostic LEDs, check them prior to connecting your equipment.

They will indicate various operating conditions when the surge suppressor is plugged into a live 120V

AC outlet and the surge suppressor’s power switch is on.

“PROTECTED” LED: Indicates the surge suppression components are intact and providing

complete protection against surges. If this LED does not illuminate, some of the surge suppression

components are not functioning, and the unit should be replaced. Visit www.tripplite.com/support.

“GROUNDED” LED: Indicates wall outlet is grounded and surge protection can properly

function. If this light DOES NOT illuminate and power is present, consult a qualified electrician to

examine your outlet’s wiring.

“GROUNDED” LED (STIK and SUPER8 only): Indicates wall outlet is grounded and surge

protection can properly function. If this light ILLUMINATES and power is present, consult a

qualified electrician to examine your outlet's wiring.

“LINE OK” LED (select models): Indicates 120V AC power is present with no wiring faults

detected.

Connect Your Equipment to the Surge Suppressor’s AC Outlets: Plug your equipment’s power

cords (including 2-wire devices) into the surge suppressor’s AC outlets. Select models feature

integrated safety covers which cover the outlets when not in use. Other models feature special widely-

spaced outlets to accommodate transformers without covering other outlets. DO NOT plug in

extension cords. DO NOT OVERLOAD the surge suppressor’s outlets. The surge suppressor can

accommodate a total equipment load of up to 15 amps (whether plugged into a single outlet or spread

out over multiple outlets). If the load on the surge suppressor exceeds 15 amps, the circuit breaker*

will trip and the outlets will stop providing power. If the circuit breaker trips, reduce the load by

unplugging some devices. Depress the circuit breaker to reset.

* Circuit breakers are integrated into the power switch on select models and offered as a separate feature on other models.

201010194 93-2666.indd 2 11/12/2010 9:36:52 AM

Connect Your Equipment to the Surge Suppressor’s Phone Jacks (Optional Installation.

Available on Select Models Only): Connect a phone cable from the wall jack directly to the surge

suppressor’s RJ-style phone jack labeled “IN.” Connect a phone cable from the surge suppressor’s

RJ-style phone jack labeled “OUT” directly to the device to be protected. Select models feature two

“OUT” jacks; either one or both of the jacks may be used, but protection is for a device or devices

sharing a single line only. All models with phone line surge protection, except the TLP810NET, protect

devices on a single line only. TLP810NET models feature a single set of RJ-style phone jacks which

protect devices on two lines. The surge suppressor must always be the first item connected in line from

the wall jack. The surge suppressor must be plugged into a 3-wire, grounded AC outlet for phone line

surge protection to work.

Connect Your Equipment to the Surge Suppressor’s Network Jacks* (Optional Installation.

Available on Select Models Only): Connect a data cord from the wall jack or cable/DSL modem

directly to the surge suppressor’s network jack labeled “IN.” Connect a data cord from the surge

suppressor’s network jack labeled “OUT” directly to the device to be protected (typically a computer’s

network interface card).

The surge suppressor must always be the first item connected in line from the Ethernet source

(typically a wall jack). The surge suppressor must be plugged into a 3-wire grounded AC outlet for

network line surge protection to work.

Connect Your Equipment to the Surge Suppressor’s Coaxial Jacks (Optional Installation.

Available on Select Models Only): Connect a coaxial cable from the wall jack directly to the surge

suppressor’s “F” style coaxial jack labeled “IN.” Connect a coaxial cable from the surge suppressor’s

“F” style coaxial jack labeled “OUT” directly to the device to be protected. Select models include a

second set of coaxial jacks for simultaneous connection and protection of devices on two separate lines

(cable, antenna or satellite). The surge suppressor must always be the first item connected in line from

the coaxial wall jack. The surge suppressor must be plugged into a 3-wire grounded AC outlet for

coaxial line surge protection to work.

* 10/100 BaseT/TX, Token Ring. Not compatible with PoE (Power Over Ethernet) applications.

Installation (continued)

FCC Part 68 Notice (United States Only)

If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible,

they will notify you in advance. If advance notice isn't practical, you will be notified as soon as possible. You will be advised of your right to file a

complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the

proper operation of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain uninterrupted service. If you

experience trouble with this equipment's Modem/Fax Protection, please visit www.tripplite.com/support for repair/warranty information. The

telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure the equipment

is not malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This equipment may not be used on

coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission

or corporation commission for information.)

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship

for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its

sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges

prepaid) to: Tripp Lite, 1111 W. 35th St., Chicago, IL 60609. Seller will pay return shipping charges.

The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system. The warranties

of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER

MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY

APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION

TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL

DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights,

and you may have other rights which vary from jurisdiction to jurisdiction.)

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended.

Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of

these devices for any specific application.

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

Lifetime Limited Warranty

201010194 93-2666.indd 3 11/12/2010 9:36:52 AM

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	Protect It! TLP606SSTELB
Kleur van het product:	Zwart
Gewicht:	510 g
Breedte:	50 mm
Diepte:	299 mm
Hoogte:	27.9 mm
Snoerlengte:	1.829 m
Gewicht verpakking:	580 g
Breedte verpakking:	100.1 mm
Diepte verpakking:	38.1 mm
Hoogte verpakking:	329.9 mm
Land van herkomst:	China
Kleur kabel:	Zwart
Draadloos:	Nee
Ophangsysteem voor aan de muur:	Ja
Stekker:	NEMA 5–15P
Piekvermogen:	1800 W
(Buitenste) hoofdverpakking hoogte:	117.5 mm
(Buitenste) hoofdverpakking breedte:	352.4 mm
(Buitenste) hoofdverpakking brutogewicht:	3840 g
(Buitenste) hoofdverpakking lengte:	254 mm
Hoeveelheid per (buitenste) hoofdverpakking:	6 stuk(s)
AC-ingangsfrequentie:	60 Hz
Aantal producten inbegrepen:	1 stuk(s)
GTIN (EAN/UPC)-nummer (buitenste) hoofdverpakking:	10037332190076
Surge energy rating:	1440 J
Aantal AC uitgangen:	6 AC-uitgang(en)
Nominale input voltage:	120 V
Stopcontacttypes:	NEMA 5–15R
Golf protectie functies:	Modem,Telephone
Piekstroom, common mode:	35500 A
Klem voltage:	120 V