Tripp Lite APSX6048VRNET Handleiding

Tripp Lite Niet gecategoriseerd APSX6048VRNET

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite APSX6048VRNET (48 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/48

Owner’s Manual

APSX Pure Sine Wave

DC-to-AC Inverter/Chargers

Models: APSX3024SW, APSX6048VRNET

Introduction 2

Important Safety Instructions 2

Feature Identification 3

Operation 4

Configuration 5

Battery Selection 8

Battery Connection 9

AC Input/Output Connection 10

AC Generator Input 10

Service/Maintenance 11

Troubleshooting 11

Warranty 12

Español 13

Français 25

 37

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

® is a registered trademark of Tripp Lite.

Important Safety Instructions

Introduction

SAVE THESE INSTRUCTIONS!

This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all

Tripp Lite Inverter/Chargers.

Location Warnings

• Install your Inverter/Charger in a location or compartment that minimizes exposure to heat, dust, direct sunlight and moisture.

• Although your Inverter/Charger is moisture resistant, it is NOT waterproof. Flooding the unit with water will cause it to short circuit and

could cause personal injury due to electric shock. Never immerse the unit, and avoid any area where standing water might accumulate.

Mounting should be in the driest location available.

• Leave a minimum of 50 mm clearance at front and back of the Inverter/Charger for proper ventilation. The heavier the load of connected

equipment, the more heat will be generated by the unit.

• Do not install the Inverter/Charger directly near magnetic storage media, as this may result in data corruption.

• Do not install near ﬂammable materials, fuel or chemicals.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the

unit’s internal cooling, eventually causing product damage not covered under warranty.

• Mount your Inverter/Charger BEFORE DC battery and AC power connection. Failure to follow these instructions may lead to personal injury

and/or damage to the Inverter/Charger and connected systems.

Battery Connection Warnings

• The battery should be connected before operating the Inverter/Charger.

• Multiple battery systems must be comprised of batteries of identical voltage, age, amp-hour capacity and type.

• Because explosive hydrogen gas can accumulate near batteries if they are not kept well ventilated, your batteries should not be installed

in a “dead air” compartment. Ideally, any compartment would have some ventilation to outside air.

• Sparks may result during ﬁnal battery connection. Always observe proper polarity as batteries are connected.

• Do not allow objects to contact the two DC input terminals. Do not short or bridge these terminals together. Serious personal injury or

property damage could result.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of

the life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

• Connect your Inverter/Charger only to a properly grounded AC power source. Do not connect the unit to itself; this will damage the device

and void your warranty.

• The main grounding lug should be connected to earth ground with a minimum 3.15 mm diameter 8 AWG wire.

Operation Warnings

• Your Inverter/Charger does not require routine maintenance. Do not open the device for any reason. There are no user serviceable parts

inside.

• Potentially lethal voltages exist within the Inverter/Charger as long as the battery supply and/or AC input are connected. During any

service work, the battery supply and AC input connection should therefore be disconnected.

• Do not connect or disconnect batteries while the Inverter/Charger is operating in either inverting or charging mode. Operating Mode

Switch should be in the OFF position. Dangerous arcing may result.

Congratulations! You’ve purchased the most advanced, feature-rich Inverter/Charger designed as an alternative energy source during

utility power failures. Tripp Lite APS Inverter/Chargers keep your equipment constantly up and productive through all utility power problems

(blackouts, brownouts and high voltages) by automatically inverting DC power from user-supplied batteries into AC power. Built-in Isobar®

surge suppression provides an additional level of equipment protection. When utility power is present, APS Inverter/Chargers automatically

pass through power to your equipment while simultaneously recharging your connected battery bank. APS Inverter/Chargers are the quiet

alternative to gas generators during emergency backup applications—with no fumes, fuel or noise to deal with! You get AC electricity

anywhere and anytime you need it.

Feature Identiﬁcation

1 Conﬁguration DIP Switches: Optimize Inverter/Charger

operation depending on your application. See Conﬁguration

section for setting instructions.

2 Operating Mode Rocker Switch: Controls Inverter/Charger

operation. The “AUTO/REMOTE” setting ensures your equipment

receives constant, uninterrupted AC power. It also enables the

Inverter/Charger to be remotely monitored and controlled with

an optional remote module (Tripp Lite model APSRM4, sold

separately). The “CHARGE ONLY” setting allows your batteries

to return to full charge faster by turning the inverter off, which

halts battery discharging. The “OFF” position de-energizes the

unit (including its AC output). See section for setting Operation

instructions.

3 Operation Indicator Lights: Intuitive “trafﬁc light” signals

show whether the Inverter/Charger is operating from AC line

power or DC battery power. It also warns you if the connected

equipment load is too high. See section for Operation

instructions on reading indicator lights.

4 Battery Indicator Lights: Intuitive “trafﬁc light” signals show

approximate charge level of your battery. See Operation

section for instructions on reading indicator lights.

5 DC Power Terminals: Connect to your battery terminals. See

Battery Connection section for connection instructions.

6 Hardwire AC Input/Output Terminal Strip (Access Panel):

Securely connects the Inverter/Charger to facility electrical

system. See section for connection Input/Output Connection

instructions.

7 Knockouts for AC Input/Output Conduits

8 Remote Control Module Connector: Allows remote

monitoring and control with an optional module (Tripp Lite

model APSRM4, sold separately). See remote module

owner’s manual for connection instructions.

9 Battery Charge Conserver (Load Sense) Control:

Conserves battery power by setting the low-load level at which

the Inverter/Charger’s inverter automatically shuts off. See

Conﬁguration section for setting instructions.

10 Main Ground Lug: Properly grounds the Inverter/Charger to

earth ground. See section for connection Battery Connection

instructions.

11 Thermostatically Controlled Cooling Fans: Quiet, efﬁcient

fans regulate internal temperature and prolong equipment

service life. Fans run at variable speed, depending on

temperature and load.

12 Remote Generator Start Connector: Automatically cycles

generator based on battery voltage. Use with user-supplied

cable. See section for more information.Conﬁguration

13 Remote Battery Temperature Sensing Connector: Prolongs

battery life by adjusting charge based on battery temperature.

Contact Tripp Lite for optional temperature sensing cable

accessory. See section for more information.Conﬁguration

14 RS-232 Serial Communication Connector

(APSX6048VRNET only): Can be used to attach an

external SNMP/Web management module (Tripp Lite model

SNMPWEBSOLOHV) to remotely monitor your inverter/charger.

15 12V DC Power Connector (APSX6048VRNET only):

Independently powers SNMP/Web management module

(Tripp Lite model SNMPWEBSOLOHV) without the use of an

AC outlet.

11213

7 11

4 8 3

On Side,

Not Shown.

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	APSX6048VRNET
Kleur van het product:	Zwart
Gewicht:	48310 g
Breedte:	227.6 mm
Diepte:	494 mm
Hoogte:	256 mm
Gewicht verpakking:	59420 g
Breedte verpakking:	368.3 mm
Diepte verpakking:	590.6 mm
Hoogte verpakking:	406.4 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Land van herkomst:	China
Certificering:	RoHS
Bedoeld voor:	Universeel
Ingangsspanning:	208-230 V
Uitgangsvermogen:	6000 W
Soort voeding:	Binnen
Stroomspanning bescherming:	Overspanning
Frequentie:	50/60 Hz
Spanning:	230 V
Piekvermogen:	12000 W
(Buitenste) hoofdverpakking hoogte:	406.4 mm
(Buitenste) hoofdverpakking breedte:	368.3 mm
(Buitenste) hoofdverpakking brutogewicht:	59420 g
(Buitenste) hoofdverpakking lengte:	590.6 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Code geharmoniseerd systeem (HS):	85044090
Output frequentie:	50/60 Hz
Instelbare uitgangsspanning:	Ja